Відео

Lets address the chocolate milk thing first, sugar in chocolate milk will coat the charging port and short it, it likely also got into the board area and corroded that as well. Send them to us and we can repair them, information in the more section above.

Either way you need to take it apart and clean the chocolate milk out of them, be very thorough!

Hard plastic, do not use super glue of any kind it just makes a mess, you are better off using a hot iron or even a soldering iron and remelt the plastic, practice on something else first and use a filter box fan or very good ventilation as you dont want to breath the fumes, once you get it figured out you will be able to plastic weld with the best of them, after doing this you can use fingernail file or sand paper to smooth it out, paint also if you like.

I have honestly never ran into one that the bluetooth did not work on, are you using the sony application? I would verify your phone does not have issues like maybe clean all the old stuff you connected via bluetooth in your bluetooth devices, try cleaning that first, the main board carries the bluetooth so you might want to look it over after purging old devices, try it on another phone also.

@@darkwarrior478 i’ve did all of that it still connects but disconnects after about a minute. i have to turn it on and on again to connect for it to turn off after a minute again

@@JoseRamirez-kd7qy Next to impossible to diagnose that type of issue without having them in front of me, something might be getting warm or shorting, try plugging it in to charge and pushing the power and options button at the same time to reset them, hold that down for about fifteen seconds and it will reset to factory settings.

Are you sure??? I bet there are literally tons of service members on the ship that drink coffee and they would argue that point!

That is why I repair it the way I do, removing the pins from the connector is very tedious, not to say it can not be done but in my opinion is just as likely to break a catch on the socket for the wire as anything, I have done this myself, you usually can find a company that sells the parts to get one from, I have a bunch so send me an email and I can send you one.

@@darkwarrior478 Hi DarkWarrior478, Is it possible to get one sent as well?

You can not just pull or go slowly with it, reach in with a spudger or similar tool and pry out in a smooth motion but feel what you are doing, i usually insert it by the top left of the pad and i have broken a couple in the hundreds and hundreds I have removed but they will go right back in place, hope this helps.

No, the U.S.

Watch the video, answered there.

There is a small piece of fabric that likely came out of it.

@@darkwarrior478 do you have a picture of that fabric or I can insert some fabric in there ?

@@AyushKumar-rg6jw Watch the videos and you will see it, i show that specific piece and likely comment on it.

If its not broken I would leave it alone, you might return them if you really are bothered by it.

@darkwarrior478 I thought that there are different compartments in each ear that might make them slightly different

Replace the right mic as well, make sure you have the polarity correct, positive to positive and negative to negative or it will negatively affect the sound.

amtech 559

Yes because it is used for noise cancellation.

Yes it is, truly!

We do this for much less than that, you just need the hanger repaired right? I replace the slider shaft part that breaks and really do not charge that much, 67.00 currently, see under more our email addy, send them to us and I have them repaired and back to you in no time.

The design looks to be deliberate so it would eventually crap out. I mean who in their right mind would use such cheap plastic material knowing the amount of stress put on it during regular use. Also, the fact that they made it so hard to repair basically tells you to buy a new one instead 😅

Go on ebay and they have parts on there or send them to us, 67.00 total and that includes shipping.

That one was a name brand and I am a bit rough on tools so it did not last more than a year, bought some that looked just like it but much less expensive, work just as well, will show them in next video.

I might make another video, I have changed the location of the repair to the middle of the slider shaft, it fits nicely and is out of sight, not sure if it is easier or not but it seems better overall!

Have been successfully repairing these like this for over a year now and it is reliable, problem I ran into with pin removal was they dont always stay in the socket after reinstalling and that is not good, also found I broke the tiny locks quite often, this works very well in my experience!

@@darkwarrior478 I got the 1mm shrink tube but its shrink rate is only 2:1. I've measured the existing wires -- and even accounting for a little squish -- are around .37mm each. So I've ordered some .5mm shrink (1.7:1 shrink rate) I dont have much room to stagger the solder joints.

@@tspike7 You wont need to stagger them, as long as you keep away from connector by at least quarter inch you will be fine, they fold over nicely, not sure what my shrink rate is on shrink tube I purchased, bought a bulk lot of it in orange and white.

@@darkwarrior478 can you tell what gauge wire is being used? I may have messed up a bit. If I can extend the wires just a bit, I should be able to make it work (also give a bit more maneuverability) I have some small shielded wire but it’s prob 24 gauge and I don’t want impedance mismatching

@@tspike7 Have not had any issues with the 1mm shrink and in fact am very impressed with the shrink tube I purchased, it is very high quality heat shrink, you wont change the impedance enough to notice without measuring it, you get the wires mismatched and that is obvious though, much noise in one speaker.

Likely the speaker has failed, have had to replace quite a few of those, you can replace them but you will need to both solder and hot glue the speaker in place, email us if you need further assistance.

@darkwarrior478 I see, thanks for the quick reply!

Nice job, if you take your time and be careful you can do this and save yourself the money, if you run into an issue let us know and we can help, have a great day!!!

Did the sound quality took any hit

You are welcome!

Good plan, they will likely be coming out with new ones between spring and summer possibly.

We have the information to contact us in the details above under more, have a great day!

how did you solve the problem? i have an xm5 and i can hear hissing in my right ear(((.

If you break them on the right side then you do that side, if left then do the left side, it is the same either way, we have repaired so many of these it is just common place now, send me an email if you run into trouble.

i have same problem. did you fixed that?

I have had to replace the whole speaker before when you get wierd bass noise so that is a possibility, look for damage on them, in that case you could buy another pair from online someplace to test with.

You can find used ones on ebay and other sites, little searching brings results, search for sony wh-1000xm5 hanger, pivot or swivel, Happy New Year!

i bought mine on ali express its coming in about two weeks

It was not made very well in my opinion, thin plastic and a short piece of brass hold the swivel, not a good design!

Thanks for this story. I won't be buying them now. Suck it Sony.

They will likely be coming out with xm6 series in couple months, might even have the test ones on for testing but do agree, Happy New Year!

Go on ebay or some other place that has sony headphones for sale, it wont hurt to try other mics that size, I have used other ones from different locations on the headphones and they work properly.

Avoid abuse with these, do not throw them around, do not sit on them, do not run over them with your car or child, they seem to be a bit on the weak side in that joint, that is my best advice!

Bro there is nothing you can do. I am a middle aged woman who takes super good care of her stuff, my Amazon $30 headphones last me 3-5 years, these stupid things lasted 7 months!! see my comment above to see what Sony told me about it, after waiting on hold to speak to someone at corporate. to make them last put them in the case and don't use them often I am so mad bc they're expensive, I could've got B&W or sennheiser or whatever if I knew, I always thought of Sony as av good company. I am so disappointed.

@@MsNeuroSpicEE Another detail I do notice is that people tend to twist them past the stops on the swivels, that is not a good idea either as it will wear on the joint over time and something will break.

Yes I can and just send me a message at the email located under the video part that says "More".