Відео

That was zero help. Thanks for nothing.

I have a Rainsoft softener (from 2019) that was not registering water use in the house. I removed the meter to find that the fan blades were not moving at all! I proceeded to remove the cap securing the turbine (fan blades) and cleaned the mini-turbine. It needed to be soaked in warm water and vinegar to loosen the years of calcium and rust. LOTS of crud came out with a light scrubbing with a soft finger nail brush!!! After reassembling the meter, a light blowing into the fan caused it to move. I put all pieces back together and now it works again! Success!!! Thank you!!!!

kind of useful but still need to see how it is actually done

How full should mybsalt tank be with water ? I keep my salt pretty topped off most of the time ao i dont see water unless looking down float

I have an issue with the cold water smelling. Found out the plumber connected the backwash drain to the 4" sanitary line at the top of the pipe. I also am using crystals, was told to go back to pellets. There cleaner. The Rheem rep said you may have gotten a couple of crappy bags of salt. So l am letting it run down low enough so l can take out the remaining salt and clean out the salt tank because it's dirty. I may wipe the sides down with some diluted bleach. I also have to move that connection to a P trap set up with an air gap. When l add the new salt should l add some water to the bottom of the tank because it's going to be dry after l clean it. Also when the salt is low the light flashes. Will this keep the water softener from doing a regeneration rinse??? This is a Rheem RHS32 unit.

Great video, very helpful. Thank you

My brine cycle is programmed at 19minutes and refill is set to 3minutes, the brine tank is empty for 1/2 of the brine cycle, i.e. the water has been taken out of the tank by around 9minutes then a further 9minutes run without sucking brine. Is it correct? Another strange thing is that even though it appears the tank is no longer emptying, water is still coming out of the drain tube.

Does the Genesis use a Clack valve?

Thank you.

!

Question I'm staying with friends A man put 4 bags of salt into the tank Owner Says the system is messed up now How can you tell if it is? Etc

Where can I find these?

Ok

Thank you so much I have been trying to find one straight forward article adressing this issue. I'm glad I found it in this video ❤

I do not have an ozone generator, what do I do with the white check valve it is an iron filter so there is no brine line correct?

Hello, I ran out of salt and also water. I'm a new home owner so I went out and bought salt and refilled but realized there is no water. Will the water regenerate once I hit that button in about 6 hours? Or do I need to manually put water in..?

Hello. I have a Fleck 5600 SXT Upflow water softener with 3/4-Inch Plastic Paddle Meter Assembly. What type of grease can I use for the O-ring (Item No 11, Part No 13305) of the Paddle Meter Assembly per the manual?

Does this apply for the genesis 2 tannin filtration system?

Is it normal to see the water is a bit brownish? I don’t know if it’s the container making it look that colour or what.

Much appreciated

Thank you so much just got mine fixed ! It was exactly that!!

Thanks for the video! One question - the replacement meters that I see online come with a cone-shaped plastic filter. My Fleck 5600SE doesn't have this part, and it isn't present in the service manuals for either the 5600SE or the 5600SXT. Do you know where this part is supposed to be installed?

Can I use this water softener on well water that has a TDS of 1687?

I assume he recommends the brand that's sitting in from of him on the table as a high quality option?

Smart ass and refill time is how long than

Our water softener stopped softening maybe 6-7mos ago. Should i be fine to just go ahead and add salt then regen after the 6hrs?

So I bought a home and I want to know the capacity of the softener that's in the home. That's what your title seems to indicate I can find here. Nope.

Thank you for recording and posting this valuable educational video.

Which Fleck is a whole house water filter and water softener?

How long I need to change the resin ? 3 day ? 3 weeks ? 3 months 3 years ?

What Is E2 warning? Saying system maintenance….and beeping …

I was told when you can see visible water in tank to add more salt. Is this true ?

How many grains of hardness can it take out per regen, and how much salt per regen?

I found if I fill the tank up more then a few 20kg bags at a time I will get salt bridging issues...

thanks

My readout cycles between the time of day and four dashes - - - - . It doesn't give me gallons until recycle. How do I fix that? All the other settings are correct.

Good morning, i just needed yo know what type of resin and carbon i need for my softener. It is a westinghouse 3WDC4432L. Please advise when you get a chance.

Thanks for nothing

Thanks for the video! I was looking for some more information. Do you know the reason for beeping sound from the water softner? Is it because of low salt levels? Is there any way to reset it once it refills? Thanks in advance

Not sure it is simply time as there is a float as well that works much like a toilet bowl float…

Great video, u got a new buyer

Thanks Biden! Lol

I have a Entek water softner system. It has more than half of the tank salt but still says check salt level. And the brian tank has water above the salt.

Much appreciated

What would be the problem if my tank continually fills up 3/4 of the way with water way over the rest of the salt?

Hello. I have an STX 5000 and is showing on the display P390 and în right corner down says x1000. Did someone knows what means?

Where is the drain tube?

Can I add a second salt tank (ie garbage can) and connect the two via siphon tube? That is, no additional holes in either the real tank nor the backup tank (except maybe in the lids). I am away from my beach house for many months at a time and would like to keep running the softener unattended for that time I am away.

What kind of salt is best to use for these tanks?

So I have a quick connector 3/4 x 1” x24” does this mean the water line is 1 inch and the adapter is 3/4?