Відео

Thank you sir

Just so you know. Unless your 100% cotton jeans are FR treated, THEY WILL BURN. AWS current recommendation in Z49.1:2021 is " E4.3 Heavier materials such as leather or Flame Resistant Clothing (FRC) which has been chemically treated to reduce its combustibility or is inherently flame-resistant are preferable to lighter materials because they are more difficult to ignite.

Good video but you have an error. On the intermitting weld symbol you state it is on center to center but show the spacing. In the video you have a 1 - 3 (L - P). The weld would be welded as 1" and have a 2" space between weld. the easy way to do this is take the Pitch minus the length. 3-1=2. Thank you everyone.

If we point the arrow from bottom side, then how we decide arrow side and other side?

Legenda,top.

Heavy are you still around? did you finish the build? Also, thanks for making the videos, really helpful.

Brother you are awesome!!!! Journeyman welder of 30 years. Refresher course starting shop job next week. A ton of fabrication prints. Your videos are perfect, videos are perfect.

great mateeeeeeeeeeeeeeee thank uuuuuuuuuuuuuuu

great mate useful thank u do filler wire and types of tungsten

ggreat viedo sir useful viedio love from indiaaaaaaaaaaaaa mumbai

great sirrrrrrrrrrrrrrrrrrr useful video from indiaaaaaa

sir do austrlia vetassess tra drawing blue prints

great job sirrrrrrrrrrrrrr

Nice 💪🏾🔥🔥🔥💨

Great video

Thank you so much for your videos! I been reviewing the chapters in the textbook and it’s a good refresher.

2023 👍

Hello, very nice videos you're making, many thanks. How can I get the whole guiide ? Thanks again

Thank you boss..

Мне надо такую зажигалку 👍🙂

I hate 6010 😂

I need all of your videos bad &I went to school...

Thanks 🤘

I need this 1 more then ever 😩 man thanks......🫡🫡🫡🫡

Grate video. I'm glad I found u...

Man I'm fresh out of school and really needed this thanks.. 🙌

If you flip the concave it will turn into convex, I got a bit confuse about it.

Great content Mr. heavy 👍👍👍

right side view is 1 3/4 and front view is 3 11/16

yes! I made perfect notes for my shop and I will be ready to cut like a pro and teach new hires! THANK YOU!!!!

Thanks! Catching up and getting on with it! Great concise video thank you for that!

The answers are the length and width...

Good job! Buddy

You a bubblehead? I as on a "target" AS31 and AS11 MANY YEARS ago.

heres a comment so yall dont have to watch the whole video, the guy talks about wearing proper ppe such as steel toe boots, cotton socks, welding cap, welding hood, proper welding gloves, cotton welding jacket and saftey glasses.

sir is am correcrt.......the symbol of slot welding an plug welding is same but only difference between is in that square if diameter is given then it is slot welding an if it is diameter symbol not given it is simply plug welding......

Great starter video! Exam tomorrow…this is helpful

Ya the video quality is not good enough for me to see the writing lol, should have atleast zoomed in close to the board

At what point or when should I remove the lock and clean up the crude/smootz/rust (pretty much surface) off of it and the parts behind the face of the lock. thanks. AWESOME video

so nice good job

Great video

Thank you !!

Top view doesn't match the front and right view.... unless I'm trippin

@2:30 time frame, the 1-3 I was told is one inch weld and the 3 was space from center to center between welds. Honestly, this makes more sense

Thank you sir

Hey Gary the plans link is not working now any updates?

Well done , easy to under stand you ,thank you.

I wish you would have repeated the answers when pointing out the lines but thank you it was a good video

You are the best. Thank you so much

thanks brotha!!!!!!