- 14
- 70 710
Robyn Racing
Belgium
Приєднався 2 кві 2012
VESPA ACMA GL Pinasco Vespone 190
Wideframe on steroids 🔥 🛵
ACMA GL
-Pinasco Superslave
-Pinasco Vespone 190 cc
-Pinasco gearbox 4 speed
-Pinasco Flytech -22 degrees at 2500 rpm
-Adjusted Polini PX ! reedblock😎
-Polini PWK 30 mm
-Malossi MHR largeframe exhaust
-26.8 Bhp at 7268 rpm
-27.1 Nm at 6708 rpm
ACMA GL
-Pinasco Superslave
-Pinasco Vespone 190 cc
-Pinasco gearbox 4 speed
-Pinasco Flytech -22 degrees at 2500 rpm
-Adjusted Polini PX ! reedblock😎
-Polini PWK 30 mm
-Malossi MHR largeframe exhaust
-26.8 Bhp at 7268 rpm
-27.1 Nm at 6708 rpm
Переглядів: 619
Відео
How to win power without spending money
Переглядів 6614 роки тому
Bearing replacement of the sprocket carrier. www.robynracing.com
Dynorun Aprilia RS 140
Переглядів 11 тис.4 роки тому
36 HP Aprilia RS 125 Setup: - Italkit 140cc 1-ring kit Italkit dome - Dellorto 34mm carb - Std airbox
Dynorun Aprilia SX 125: Original setup
Переглядів 11 тис.4 роки тому
27 HP Not the highest number but a bike with a nice daily-driver capability and smooth powerband. Original is all that matters right here 💯🏍💨 Setup: - Original 125 - Original VHST 28mm (electronic E3 carb) - Giannelli exhaust - Original air filter Don’t forget to visit our shop at www.robynracing.be
Moriwaki MD250H on circuit de Croix-En-Ternois (FR)
Переглядів 4514 роки тому
Moriwaki MD250H on circuit de Croix-En-Ternois (FR)
Moriwaki MD250H on Carole Circuit (FR)
Переглядів 1,5 тис.5 років тому
Moriwaki MD250H on Carole Circuit (FR)
Aprilia RS 125 dynorun
Переглядів 6 тис.5 років тому
Setup: - italkit race conrod - italkit 140cc 1-ring - VHM cylinderhead - dellorto 34mm vhsb - italkit inlet manifold with carbon reeds - italkit pneumatic powervalve - EBC raceclutch - jollymoto corsa exhaust Soon more videos of testruns!
Rotax 122 clutch adjustment
Переглядів 12 тис.5 років тому
Clutch tool used in this video, available on our webshop: www.robynracing.be/shop/aprilia/sx-125/clutch-sx-125/clutch-tool-for-rotax-122-aprilia-rs-125-92-12/ If you have any other request about a how-to video, let us know in the comments! 😃
Rotax 122 clutch cable remove/install Aprilia RS 125
Переглядів 19 тис.5 років тому
If you have any other request about a how-to video, let us know in the comments! 😃
Aprilia RS 125 trackday Croix-en-Ternois august 2018
Переглядів 4295 років тому
Aprilia RS 125 trackday Croix-en-Ternois august 2018
Timelapse Rotax 122 engine bottom assembly
Переглядів 1,8 тис.6 років тому
Aprilia RS 125 engine Camera: GoPro Hero 4 Silver
Aprilia rs 125/140 GoPro Hero 4 Silver
Переглядів 1,8 тис.7 років тому
Circuit: Croix-En-Ternois Setup: Italkit 140 cc kit with Vertex with 1 ring VHM custom made cylinder head Light Conrod Reinforced EBC clutch Italkit Carbon reed valve Dellorto 34 mm Jolly moto corsa exhaust Original powervalve Original airbox with twinair filter Wilbers front fork springs WP rear shock Gilles tooling footpegs Pirelli supercorsa tyres
bro thx from germany
bro ur aprilia is strong but my is stronger prolly goes like 300kmh but dont ride it so hard because i have so big back its not aerodynamic!!!
i can't see the stopper😢
rave?
What main jet did you use on this run 160?
Please tell me what exhaust you have
It's written Arrow on the muffler...
Did you use the ktm lc4 wiring loom?
Which Main jet?
Dautre videos.du projet?
Thank you exactly what I needed after rebilled 😉
27 at the wheel or at the clutch?
Wheel
Geeeuw 😴
Bere
is this possible without this tool?, with some Screwdrivers or something???
where can we buy parts for aprilia mx 125 c 2005?
Robyn racing website
the older aprilia models dont have these bearings, do they?
Did you drill a hole in the ecu? Whats Top speed and in which gear did you tested the bike?
Jak się sprawuje aprilia?
Very cool bro. Thx
The chain is a bit to tight😲 but nice Power👍
It’s a 2t or a 4t ?
Bro ....
Tell me a 4stroke 27 Hp 125ccm Bike
Can't you hear the difference u goon and what shape is tye exhaust ya frikin newb
when is the best time to rebuild the engine? i bought my aprilia with 39k km on it. but i dont know if the seller already reassembled the engine. Is there like any signs a bad rotax engines give to you like vibrations or klacking sounds?
Rexona
O
Hahs
Do U recommend arrow exhaust or genielle
They are the same
Arrow ofc
Where can I find a replacement for that plastic bolt. The previous owner used a screwdriver and it's all messed up like you showed in the video aswell
Hi, we sell these of High Quality billet aluminium. Available in multiple colors. www.robynracing.com/shop/aprilia/sx-125/engine-sx-125/aprilia-rs-125-cnc-oil-filler-plug-set/
@@RobynRacing hartelijk dank. Zojuist besteld
hp?
35,6 BHP DIN
Hi! I need some help. I have adjusted the clutch as the video explains, but clutch is not disengaging fully. So when i put it in 1st gear with out giving any revs engine stalls. If i rev to 2-3000rpm i can keep the bike running but it will still want to move forward a small amount.
First try to turn back less than 180 degrees (in the video we said 180 as reference), if that doesn’t work you have other issues (ex. Cable worn, clutch arm, clutch basket, etc) be sure to check inside if this doesn’t work.
Cool, what mainjets and pilot jets do it use for this specific engine?
Hi, don't know exactly. Has been a while since we worked on this bike...
straights for show corner speed for dough 💰 👍
Any other way if i dont have the clutch tool?
If you have a hollow 11mm socket, you can use this as well. Good luck!
@@RobynRacing thank you very much!!
@@MRryuhayabusa No problem!
What jets did you use in the 34mm and what notch was the needle at? Thanks!
Hey, will adjusting it help me solve the clutch not releasing at all, when I pull in the clutch it doesn't release and if the bike's in gear it wont move forward freely unless I'm forcing it. Then it makes a "clunk" sound and wants to start !
Inner hub probably worn, if adjustment fails this is 90% the reason if clutch plates are still okay. Pressure plate and adjustment bolt will be the next thing to fail when running too long with the worn inner hub. Keep us informed! 😯
@@RobynRacing Sorry for the long reply time. The main problem was in the clutch disks, they were completely toasted. I swapped them out but it didn't solve the problem instantly, they were still stuck. So I noticed that the clutch releases on 2nd gear, I went outside and gave it a go on 2nd gear, rode a bit around my driveway tried switching gears and everything seemed fine. Then I stopped in first gear with clutch pressed in and Voylaaa, it's working perfectly right now. I checked the inner basket and the inner hub, sent some pics to a friend of mine who has a lot of two strokes, he said that they're in tip-top shape :))
@@RobynRacing good video I always share your page on Instagram
Need 39mm carb or a powerjet one to get the best of a corsa exhaust
True, Corsa on std engine and carb doesn't perform well. We get very good results with 34 VHSB on Corsa exhaust. 36 BHP DIN at the wheel. 39 could be possible even better, at the moment we're playing with a Keihin PWK Airstriker 38mm. Fingers crossed! 😅😜
@@RobynRacing hope u could get even better from this corsa 💪😉 36BPH on standard is huge but u know jollymoto's the best, that's why they made the corsa especialy for the RS 125 😋✌️
@@matkaisencazou2296 That's a fact! Jollymoto exhausts rule! 😀 New video soon? 😎🤓
@@RobynRacing I will love it
@@RobynRacing Do you have an update on the 38mm PWK ?
I broke two clutch arm's...I have the older version with the screwdriver and I don't know how to adjust it. Do I have to feel the slight tension or not?
Twist clockwise until you feel slight resistance, hold the screwdriver with 2 fingers. Rest of the video is the same, so turn back 180 degrees and fasten the locknut. After that, adjust the cable slack at the clutch lever. Be sure to set the cable slack at 0 before starting adjustment. Good luck!
clutchen of engine braken in scherpe corners? hoor veel tegenstrijdende dingen over engine braken ivm smering in de naft
Remmen op de motor is inderdaad geen goed idee, aangezien er geen benzine en olie (ralentie hoeveelheid) de cilinder ingaat bij gas dicht. Indien niet met premix maar met oliepomp nog gevaarlijker. Beperkt terugschakelen is bij ons enkel voor de juiste versnelling al klaar te hebben.
Well explained, thanks 👍👍
Can you send me some stickers please
we want more!!
nice dude, thanks
Thanks 👍
No problem, happy to help 👌
Thanks for the video just put my clutch cable back in
Good videos I see you on Instagram all the time you subbed to my channel I am yours
Thanks for the support Paul! 😃
Hello. Do you speak English?
Yes we do speak English! 😃
@@RobynRacing Can I ask you for an advice? I have a rotax 123 with dellorto 34 and after I replaced the valve needle the engine doesn't start. What might be the problem?
Levente Csontos what do you mean? Powervalve on the cilinder or needle in the carb?
@@RobynRacing valveneedle in the carb.
Did you already check your carb once again? Are all parts installed in the correct way? Because it’s possible that the slide is inserted the other way around.
Hp?
ik ben hier al aan het mee genieten :-) welk parcour is dit ?
ik zal maar den eerste zijn zeker om te zeggen via youtube dat het een waanzinnig filmke is!! :p
nice video stef, who's driving?
Please can you tell me what jets you are using with this setup on the 34mm carb. Pilot jet- b36? Main jet? Cheers
Starter jet I have no idea since it’s been a while since we’ve rebuilt the engine. Main jet is 160.