Відео

I have made all sorts of things out of wood with WoodPrix plans. Sheds, garage doors, chairs, tables, etc. I've even made a fence and raised beds with these plans. They even have plans like bird feeders there. The selection is overwhelming

What type of Jack stands are you using to support the stern of the ski. Any idea where they can be purchased online. Very nice work, have you tried applying the gator glide with a roller?

What type of Jack stands are you using to support the stern of the ski. Any idea where they can be purchased online. Very nice work, have you tried applying the gator glide with a roller?

What type of Jack stands are you using to support the stern of the ski. Any idea where they can be purchased online. Very nice work, have you tried applying the gator glide with a roller?

You never answered the question why.

Hello, good job. Features does the Gator Glide paint have? Is it bituminous epoxy? Thank you!

How come you heat the fiberglas pre gelccoat? is the fiberglas and resin dried through before the heating?

What is this yellow tape?

So what are most guys charging for this?

Why not drain the oil in the fuel and flip it over it just seems like it would be a lot easier to work on

Thanks for show us how easy it is a DIY only if you have all the tools and to also lift up the ski. Not worth it for me, I rather pay for your work.

There are some good slow (24 hr.) cure urethane paints out there now, I got some for my bumpers on my RZR and I swear it is tougher than any powder coat!. (about $30 a pint) plenty enough for a hull.

Do you have to be pretty quick about removing the tape?

One of the best videos for the process I have ever seen. Which is better for durability Gator Glide, or Super Slick? I know it is mostly a subjective opinion but I bet there are good points and bad for each.

Preskoči

Is there a reason for not using gatorbase first?

Promo sm

Can you apply gator glide over a repair that has Epoxy Fairing Compound material on it or will it peel? or is it better to use polyester fairing compound? Thanks

Hello what grit sandpaper do you usually use to remove scratches?

you are great and very nice job.

perfect as usual, did you ever thin gelcoat with styrene and mek only?

That is an insanely good repair mate ,especially the gel coat match. Great channel and look forward to more content like this,well done.

That measurement business is just a bunch of bullshit they use to negotiate you down. Give the fuggers a price and stand on it. They can take it or leave it. There are not that many people that know how to do the work. You have much more control than you realize. They are vultures and need to be treated as such. You really don't need them in the marine industry. There is plenty of work without working too cheap or jumping through their silly as whoops like a circus pony !

What does it cost to have a wave runner done?

Just started my journey with fiberglass! I want to use it to modify a small shower pan for van build. Thsnks for covering some of the things i need to know. Things went beyond my knowledge when you were mixing the nonskid, but i gained! I will be shortening the pre-existing pan, and i need to add an elevated “pedestal “ for a cassette commode. A question i have is how to prep the plastic of the pan to accept the fiberglass? Is a rough sand all i need?

Love these techniques.Can test colors be mixed by a marine paint co. ?

Some of these Ski’s are not the easiest to repair and you do great work on them. I repair and make surfboards in Australia and also do plenty of boat work and can honestly say the learning curve with repairing some of the jet Skis especially the Yamahas has been steep to say the least ! I subscribed to your channel a while back and have definitely used some of your techniques on work I’ve done here so thank you and keep up the good work

Just found your channel. Love the content. Would love to see a more detailed process from start to finish.

Could you advise how much you estimate for a job like this

Excellent vidéo.i would like to know how much of gator glide do you need to put in paint gun for one layer for waverunner ?

With due respect for your video, I really wonder how you can get your bulk mix exactly the same as your sample.

It would be very helpful to see a video of you repainting a JetSki bottom and the process.

So who cares it's the botton for pete shakes

i have to replace a transom in my ski boat and maybe remove top cap and floor so I subscribed and will be following along!

excellent content very well explained . I was wondering during the glass repair when building back the laminate do you start with the smallest piece of matt and get progressively bigger with each layer or the opposite way around largest to smallest it seems to be a bit of a controversy which is the best way for some reason. Also did you use chopped strand for the repair and what ounce weight would be a good choice for a repair like this. what gun and tip size do you find works the best for you spraying gel . Looking forward to more videos

What did you use to reduce the gel coat?

Good content

Wtf??? Did he drive that down the street?

It’s just a flesh wound, grab some flex tape and you’ll be onda water in no time 😂😂😂😂

Hiii

'promo sm' 🤭

They are making so much money they have lost touch with who they are and what made them. Just bought a truck for 140k. Smh, I unsubscribed a while back

⚓️

What’s wrong with the goonsquad? They can’t fix their own problems I see this every time they start a build but they never finish it there content is really going down the toilet!

Made it look to easy

You could teach them a few tricks, that would definitely improve the quality of theirs repairs...🤣

Good job 👍

Cool