Відео

I spent an hour on this job thx to you. I appreciate it sir.

Honda Civic (2018 CVT Sport) was making a buzzing noise when locking the car. Found out that I needed to replace the Actuator Assembly Fuel Lid (Part Number 74700-TBA-A02) that locks/unlocks the car gas lid. FULL VIDEO: ua-cam.com/video/L0ICO81Rvms/v-deo.htmlsi=mYF65mX7p00kV5Kx REPLACEMENT LINK: amzn.to/4iIXT08

OP, well made video. I am making some notes for myself bc this is at least the 3rd time I have done this kit over the years and I forget the details every time. **IMPORTANT NOTE** You will be tempted to use some kind of lubricant on the rollers. DO NOT DO THIS! I tried it the last time and it got the rollers completely stuck. All I used was powdered graphite If I recall correctly. If you have the same exact dryer as me and this guy. at :37 use 1/4" socket for the 3 screws (it's used for nearly all the screws except a couple phillips). Also, I haven't ever removed the back panel. It makes access easier but reassembly harder. 3:39 that wiring harness is easier after removing the front panel with the door. There are attachments at the top that pulled right off for me. 3:47 when removing the front control panel (top panel) there are 2 plastic tabs (vertical, white plastic, push them out to the edge) you can pop on the back, one at each end. Be sure to note which hole the wire comes out through for reassembly later. 4:25 instead of unplugging the whole harness (earlier in the video), I just unclipped that wire clip to give enough slack to just set the whole front panel with door to the side carefully. 4:30 "well I broke this piece a little while trying to remove it." Me too buddy. I remember that specific moment. 4:58 I did not remove that top brace 5:00-5:08 remove the bottom 2 screws first then just loosen the top 2 screws

I removed the restrictor but now the hand held wand doesn’t work. Water comes out the main shower head great now but no water out the hand held.

What type of light you had working with @10:43?

Thank you so much !!! Your video saved me a lot of $$$ and I was able to fix the dryer in a couple of hours for only $26 !!!

Thankyou so much for this video, Great attention to detail and step by step instructions.

Nice video. Reminded me of the steps required and how to thread the belt. Thanks!

thanks for helping me fix my dryer :)

Trying to do my duet dryer the front to start the reassembly has no screw holes am i missing something

Does the motor spin when the belt is broken? my belt broke on a Duet WED9610XWO but I cannot hear the motor turning either, you mentioned fuses? where are they and hot to test them?

Preferivo il trapano a percussore con una lunga prolunga fino a beccare il duro😂😂😂😂😂😂

Buenos días amigo gracias por la información 👍 me ayudaste muchísimo

Thanks!

What belt did you use for that model? Do you have the belt number?

The starting and stopping, is that from the Greenworks head shutting down? Possibly overload protection? I’m experiencing that with using an edger attachment from my previous MTD gas edger.

You're a shower-head savior! I was so frustrated with the water pressure that I almost replaced it. I couldn't remove the white clip and ended up breaking it, but thanks to a previous comment, I used a brow tweezer to pull out the black rubber ring and it worked perfectly! Thank UUUUU!

Never would have had the confidence to do this without your video. I did it, It was the belt and now it's repaired! Many Thanks!

Very helpful. Spent $13 on a new belt and with this video fixed my dryer without a problem. Thank you!

Did this ice maker/fridge have a filter to replace for the water going into the ice maker?

❤

Thank you so much for this video! This helped a ton and you explained and showed everything thoroughly. Although mine was a little different, we were able to figure it out. Now we have a new belt and clean dryer. Thank you!

I've had this showerhead for several years now and it leaks from one head to the other. For example, if I have all the water diverted to the large head, it leaks out of the handheld, and vice versa. Is there a cartridge in it that can be changed? Also the off switch on the the handheld head barely stops any water anymore, the water pours out even when it's in the "off" position. Have you had any of these problems?

How long did this take? A 10 minute job will take me 3 hours, so if it took 3 hours for you it will take me 9 lol

I’ve replaced the inlet valve and now I can see there’s forsure more water filling but I’m still getting the f8e1 more often than not. Maybe there’s a level sensor that’s bad ?

Thank you so very much. I tore the whole thing apart and put it back together BY MYSELF thanks to your video!😁😁😁

Awesome video; Wish I found it earlier while troubleshooting my F8E1 error. Listening to the valves during a cold fill vs a hot fill was the clue I needed to isolate a valve issue. Thank you.

Thank yoy

I was looking in the wrong place for the water restricter, your video set me straight. More water pressure now. Thanks!.

I have a whirlpool washing machine front loader that’s on the blink - but too intimidated to give it a try. What forum did you go to or UA-cam channel for help? Thx for any advice- I’m a new sub - also loved your Ryobi gas edger hack with 80v Greenworks universal trimmer- I just bought the Greenworks too. So I’m excited that I saw your video. You’re awesome 👏

You’re brilliant 🎉🎉🎉

Thanks to you, I was able to replace the broken belt on my WP Duet dryer with relative ease.

I wonder if it works with 60v?

Thank you!!! The water pressure is so much better. Also, that white clip is super stubborn, needle nose pliers are must when removing.

So replace all this. What else could this be ?

Wait… who is bringing a whole power drill to the beach? 😂😂😂 This is so unhinged, I love it!

Ever figure out how to on the actual drill setting? Mine is all the way counter clockwise, just fyi.

Cómo pueden ayudarme con este tipo de lavadora lava normal pero al momento de centrifugar el agua se queda quieta y no funciona no bota el agua

I have the same identical dryer I have to do the same thing I have to replace the belt

There is no link

Exceptional. Could not find anything that matched my model, but your attention to detail helped me find a way to replace the belt, without removing the Back panel. Great Job.

Very informative and helpful. Thank you!

What is address this beach ⛱️🏖️

Thank you for recording this video. Helped me on my dryer. Busted pulley wheel. Saved me some $! 👍

Thanks for this. I wasn’t able to get the white clip out but I did manage to get a very small hooked pick around the black washer and pulled it straight out. Didn’t rip the washer and the white clips stayed intact. Water pressure is much better now

Exactly what I needed, many thanks!

I was about to return this product! Thank you! Very informative 👏

Thank you for this video. I was able to fix my dryer by myself! Great tip about the system to keep track of all the screws.

You dont have to take back cover off...can be done throughout front side only

Has anyone tried to remove the blue water saver for even better pressure?