- 93
- 6 333 399
MS engineer
Saudi Arabia
Приєднався 26 січ 2023
Foundry engineering
#Method of midwifery extraction# kabla nikalne ka tarika
#Method of midwifery extraction# kabla nikalne ka tarika
Переглядів: 111
Відео
#How to brush# K I A Carnival # engine head chori kharib brush Lagana ka trika
Переглядів 5672 місяці тому
#How to brush# K I A Carnival # engine head chori kharib brush Lagana ka trika
#How to apply liner # sleep lagane ka tarika diesel isuzu
Переглядів 6012 місяці тому
#How to apply liner # sleep lagane ka tarika diesel isuzu
#How to remove the head seat # head seat nikaalne Ka Tarika
Переглядів 1,1 тис.2 місяці тому
#How to remove the head seat # head seat nikaalne Ka Tarika
36v 350w manual cycle to electric cycle convert
Переглядів 1462 місяці тому
36v 350w manual cycle to electric cycle convert
#isuzu #how engine piston gauge rang chak
Переглядів 1,8 тис.2 місяці тому
#isuzu #how engine piston gauge rang chak
#isuzu # How to remove and apply the liner# slip nikaalne ka tarika
Переглядів 10 тис.2 місяці тому
#isuzu # How to remove and apply the liner# slip nikaalne ka tarika
#made in Korea# Hyundai sonata #ka engine crank push lagane ka tarika
Переглядів 7712 місяці тому
#made in Korea# Hyundai sonata #ka engine crank push lagane ka tarika
Land Cruiser V8 head banane ka tarika
Переглядів 773 місяці тому
Land Cruiser V8 head banane ka tarika
Олень добрый день
Ебааать мастер
🤔🤔🤔
Buy one block
Im guessing they plan on fitting larger diameter sleeves. This means boring out the Block larger. The sleeves have too thin wall thickness IMO...🤔😳🇬🇧
Those Liners have way to thin walls...If this is by design, you need some new qualified Engineers...😳😳😏🇬🇧
This video is about: How to remove sleeve and functionality from an engine.
Aaaaaaahhhhhhh no no no, god damn that hurt my soul to watch
block the demage😢😢😢😂😂😂
❤❤❤❤❤❤
And the block?
Извините, тут еще блок надо менять, у вас задир на цилиндре большой
ชิบหายการช่าง😂
That cannot be the best way to remive a liner....
I'm no mechanic but even I know that's a bad way to get the sleeves out. 👀
The gouging helps hold the next liner that will get beat in with a framing hammer
Ok, that chisel double gouge inside the remaining cylinder wall leaves it impossible to salvage that engine block.. Well played Einstein 😢
Those lines going round the bores in the begining is caused by a rip in the emery paper as you can see.
These liners are so thin as to be deformed by the combustion process necessitating this type removal. Too bad all our American vehicles aren't made this way for repair. This thin sleeve could be nico-plated for extreme long wear.
Scratch
Clean work
Ouch
Jesus fucking Christ what in the hell? Hammering on precision parts with reckless abandon, yeah?
You gotta take that sixty over even to get close from the scoring from that screwdriver
That's how not to remove a liner
Emme 20....ekzozzz25
Nu vezi că acel cilindru este praf ???🤔🤔🤔
Ножом в грудину, уверен каждый это сейчас ощутил
Я так и не понял зачем он это делает
Nope.
Wow. Fired instantly
This is a joke rite 😂😂😂😂
Astagfirullah 😭
That block is junk now. Nice gouges. Why would you even record that? It must be a how not to, video.
I wonder why I have low compression lol
While destroying the inner lining too😂😂😂
"I need it back tomorrow morning"
😮😂 Why if Any one does this just know that is out of hatred. 😂😮
😂
Everyone dislike that
I heard that technique was only for installing spark plugs?
That's how to take everything out
😂😂😂😂😂😂😂 congratulations your fired
#hownotto how to lose the customer
Destruiu o bloco.Serviço porco!
Zylinder raus meißeln. Was ein Idiot😂😂😂
Wrong
😂😂 ок
If ur gonna cut it down anyway shoulda made it thinner so u can break it without damaging the bore
А теперь борозды чем лечить будешь? Гильзу запорол ради лайка и глупого действия😅