Відео

thank you for your comments I have already taken care of that in my new videos. i am glad this video helped. please stay tuned to my channel for my future videos.

I am glad it helped. please stay tuned to my channel for my future videos

you might not get that easily unless you have a celestron shop nearby. but what you can do it get a screw of the same size from the hardware store and can by a washer ring to put over it. I hope this helps. please stay tuned to my channel for my future videos.

@@AstroShootingStars my mount is also fixed in the tripod. the previous owner said that the screw is striped and he has to bond it, is there any way to fix this aswell?

yes you are right you can leave 5&6 unsoldered for using with UART. i hope this video helped. please stay tuned to my channel for my future videos.

thank you for your comments. I hope this video helped. please stay tuned to my channel for my future videos

i am glad you liked it. Please stay tuned to my channel for my future videos.

the new chip is marked with main antenna and auxiliary antenna and it is inverted as on original chip. I hope this helps. please stay tuned to my channel for my future video.

I understand my friend, its a fairly simple process just put the clear flux it comes as a liquid and the using the solder on the iron tin the ports basically just rub over it till you see them silver shining and all ports separated. flux also helps in this process to keep the ports separate. I hope this helps. please stay tuned to my channel for my future videos.

Thabk you for your comments. I am glad this video helped. please stay tuned to my channel for my future videos

I am glad it helped. please stay tuned to my channel for my future video

yes my friend as they still use the square gate. i hope this video helped. please stay tuned to my channel for my future videos

i am glad it helped . please stay tuned to my channel for my future videos

not just six pad all the side pins as well and the put flux everywhere and then when you place back the chip on motherboard and heat those solder will melt and connect.I hope this video helped. please stay tuned to my channel for my future videos

no my friend it needs a 3d tv to process 3d signal. I hope this video helped. please stay tuned to my channel for my future videos.

@@AstroShootingStars oh

I am glad it worked. Please stay tuned to my channel for my future videos.

I am glad this video helped. Please stay tuned to my channel for my future videos.

thank you for sharing. I hope this video helped. Please stay tuned to my channel for my future videos.

no my friend this is PCIE 4 version. there are other which are PCIE 3 or less might affect the speed but if you purchase the right version you wont have this issue. I hope this video helped. Please stay tuned to my channel for my future videos

for sure internal module is capped to 250mw but you can use external module with higher wattage. I hope this video helped. please stay tuned to my channel for my future videos

I am glad it helped. Please stay tuned to my channel for my future videos

yes you need to tin the ports always so that when it is melted all pins are soldered without any miss. I glad this video helped. Please stay tuned to my channel for my future videos.

i dont know which pocket wifi you have but if you convert from wired to wifi it can work. i dont think this can repeat a 5 ghz wifi signal for 2.4 ghz signal. Please stay tuned to my channel for my future videos

I am glad this helped. Please stay tuned to my channel for my future videos.

ya se amigo. pero me mandaron este parte para cambiar completo. en mi futuro video puedo enseñar como reprar este parte también. Gracias.

I am glad it helped. please stay tuned to my channel for my future videos

thank you for your comments. I hope this video helped. Please stay tuned to my channel for my future videos.

I am glad you liked this video. I hope it helped. Please stay tuned to my channel for my future videos

ofcourse any esc can be connected to pixel hawk controller. the please follow the generic connection guide from the video to connect esc to FC. I hope this helps. please stay tuned to my channel for my future videos

you dont need external modules if you use elrs protocol compatible receiver. however if you want to have both 4in 1 and elrs you can do it via external module for 4 in 1 or crossfire. I hope this video helped. please stay tuned to my channel for my future videos.

you can change the color from your rgb controller software of the motherboard. if not ot will have default color changes. I hope this helps. please stay tuned to my channel for my future videos.

wifi 6e is more efficient chip and since it is smd it is low power as well. so far i have not seen any battery or heating issue on my steam deck. I hope this video helped. please stay tuned to my channel for my future videos.

I am glad it helped. please stay tuned to my channel for my future videos

6 beeps means esc startup error. this may happen due to several reasons. one of them is you have not connected the salve wires of esc go your flight controller. make sure you connect all wires of ESC to the flight controller. Please follow my wiring diagram to find the right connection. I hope this will solve your issue. Please stay tuned to my channel for my future videos.

thank you for your good words. I wish i could help. but you can try an external usb wifi adaptors to connect to usb port. I hope this will work for you they are also cheap. I hope this video helped. please stay tuned to my channel for my future videos.

@@AstroShootingStars how to do this bro? is it steamOS support? Can i install it on this steamdeck

Choosing between the RadioMaster TX16S with a 4in1 module and the one with an integrated ELRS module depends on your specific needs and preferences regarding communication protocols and usage. Here's a detailed comparison to help you make an informed decision: ### RadioMaster TX16S 4in1 #### Advantages 1. **Flexibility**: - The 4in1 module (CC2500, NRF24L01, A7105, CYRF6936) is compatible with a wide range of communication protocols such as FrSky, FlySky, DSMX, and more. - Ideal if you own or plan to use drones and other devices that utilize different protocols. 2. **Versatility**: - Perfect for users with a diverse fleet of models requiring different receivers. #### Disadvantages 1. **No ELRS integrated**: - If you want to use the ExpressLRS (ELRS) protocol, you'll need to buy an external ELRS module. ### RadioMaster TX16S ELRS #### Advantages 1. **Integrated ELRS**: - The ExpressLRS module is already built-in, so you don’t need to buy an additional module. - Known for offering excellent range and low latency, ideal for racing drones and long-range enthusiasts. 2. **Performance**: - ELRS is renowned for its superior performance in terms of range and responsiveness, which can be crucial for certain applications. #### Disadvantages 1. **Less Flexibility**: - If you need to use other protocols not supported by ELRS, you'll need to buy additional modules. - Less suitable if you have models using various protocols. ### Recommendation - **If you need flexibility and use different protocols**: - Opt for the **4in1** version. This will allow you to control a wide variety of devices without needing additional modules. - **If you primarily use ELRS and seek optimal performance**: - Choose the version with **integrated ELRS**. This is the best choice if you're looking for maximum range and responsiveness, especially if you mainly use ELRS-compatible receivers. ### Conclusion Depending on your specific needs: - **4in1**: Best choice for versatility and compatibility with many protocols. - **ELRS**: Best choice for optimal performance with ELRS, without needing additional modules. Make sure to understand your current and future needs to choose the version that best suits your usage.

I have the same problem bro, have found a solution?

I am glad this video helped. please stay tuned to my channel for my future videos

I am glad it helped. Please stay tuned to my channel for my future videos