Відео

Did your click multiple times like a bad battery because I have the same thing. My mechanic thinks it’s the starter. I also have a bad ground wire , wonder if that could be an issue too

Creative oil pan I'ma do this

Q

You ain't doing that with this snap ring I got to fuck with

I did this same thing and a plastic tee on the heater hose broke and i lost all my water and the car overheated but it never showed on the guage that it was hot!!! Now i think i burned it up!!! It will crank over now and the oil didn't mix with the water! So i don't know why it cranks but won't start now!!!!

I have a suggestion if you own a chevy cruise! TRADE IT IN!!!

Will this same spark plug method work on a 2008 Suzuki X7 V6

Hi did you rebuild these cylinders, or just put in new seals? Did you do the work yourself, or take it somewhere to be fixed? I have a Waldon 6000 with one lift cylinder that leaks; wondering the cheapest way to get the leak fixed. The chrome looks good. Thanks for your help.

Dont put silicon! Thats how it grounds. Metal to metal.

useless video

u shoulda seen me when my radiator hose blew off

Who engineered this dopey battery system. So much work in replacing a car battery. It use to be simple and take less than 5 minutes.

I miss the old days you don't need all these tools to change a car battery.

Thanks!

All these comments lol. If you maintain your cooking system in your Chevy Cruze you’re golden

Torque multiplying wrench would have turned this into a much shorter vid

Will it start by jumping it?

This a horrible “how to video”. Its title is very misleading. You spend the first 13 minutes taking the airbox out then don’t even actually remove the starter 😂

I’m with ya my brother. I’m going through this right now.

BMW has never put a V6 in any of their cars.

Wish they gave us a freaking metal screw instead of the crap plastic one.... What happened to the cap????? The cap was the best! Now we get a shit screw hidden out of sight.

Absolutely makes it so you will take to the shop

He.forgot the heavy washer on right side.😮

Reinstall your turbo heat shield it may actually be heating your fan up. That’s what the heat shield supposed to do is stop the transfer of the heat going out in the next thing closest to it is your radiator fan ?

Skrew holes have a metal tube in each, should prevent cracking the plastic.

This video is 2 years old. Scanned the comments looking for snarky comments about the fact that it is in his dining room. 200 gallons weighs 1600lbs. hmmmmm

you get 35 mpg? not bad,

what should you do if when you undo the bleeder screw water or fluid starts to immediately come out ?

That is the worst bleeder screw design ever. These engines run hotter at 'normal operating Temp' 226 degrees F is not good for the head gaskets, seals and plastics.

Watched your video. New battery went in fine. However, tightening the positive, the wrench accidentally touched the metal battery hold down slightly sparking. Now the car will not start. I’ve checked two fuses and they were fine. What’s the next step?

Thanks!

Solenoid is 12v, guys if you bypass the solenoid put it on a switch, the truck fuel system needs it to both start and turn off the truck when energize, normally a bad relay, fuse or broken wire will cause that, I'll ch😂ck the fuses and relays first u believe the 3116.3126 are the same

Great how to video!

pretty good oil leak there... is that actual oil or your front cv shaft seal leaking?

I didn’t notice, did you put the bleeder screw back in?

Check your thermostat housing, rad hoses, surge tank, the floor on the passenger side and or drivers side under the floor mats ( heater core ) the plastic housing on the drivers side of the engine block , you have a leak somewhere.

Working on a 2002 one and the back bolt is slide back towards the engine block how TF would I be able to put that back!?

Any chance you can share a picture of the diagram and/or the inside of the fuse box. It looks like someone messed with mine and now it won't start =/

helpful video thank you

Thank you!! Very helpful

That brake fluid was really dark. You should have bled them also.

Good info but incomplete would like to see the starter come out.

FFS why do they have to make a basic maintenance task so hard?

When installing BOTH new batteries, should I fully hook up the main prior to fully hooking up the aux or do both positives and then negatives for both? Thanks in advance

Mine is boiling in the reservoir what's the cause?

Why doesn’t my Cruze have that bleeder plug?

Just make sure you pack the bearings with dirt and grass first…

Wait so I don’t need to disengage the electronic break?

Wouldn’t start. Had to refund the customer and send them to the dealer. Triple checked all connections. Needed a battery program/relearn

massive street cred for the highway noise, those cars are going fast...and good emphasis on "you can't drop any little pieces into the dark engine bay or you're not gonna make it"