Відео

Gracias, for sharing your many years of experience

Proper 😂

Are you an actual plumber if you are witch i doubt. You would know how to cut,taper and solvent weld pipe

Nice work

I had someone do that job an I had to cut out the drain.hw never screw in the pan..he put in the liner then the drain.can I put the drain.Add the cement to the bolt level cut out liner an reseal it

Simon, I am rebuilding my Master shower in a corner right now. I cannot tell you how much I appreciate all your videos! The only thing is I hope I did not make a critical mistake by building the curb on top of the pre-slope I made with Floor Mud. It was a decision I had to make due to multiple conditions. I am about to waterproof the pre-slope and curb with very special attention to it all.

Excellent work, wish you were available in our area! Thank you for the video, very helpful

I gotta said. Straight to the point and we'll explain. Thank you sir.

I wish that you were in the Memphis area. I wish I could find someone here to install a shower like you do it. Great videos. Thank you for posting them.

I’m doing my drain this weekend this video looks. Really good

very helpful! thank you

Great video. Was the concrete that you cut out and installed the drain in sloped? Why I am asking this is that after you do the pre slope with the motar bed on the liner, wouldn't water sit on the liner since the concrete below wasn't sloped?

So I tried this on a test run, but it seemed to break up real easy

Your videos are absolutely the best and I really appreciate you making these!

Your tutorials are the best. I have looked and looked and looked for tutorials like yours and I'm very happy I found the best, right here! I really appreciate your thorough explanations!

Nice sheet lines on the floor.

Thanks 🙏

Awesome work. How long do you get to work with the dry mix before it begins to set?

I want to see how you cut around the curb corners beneath the corner dams those are tricky

Wow you didn’t miss a single step

So you are adding the pan liner on top of this?

Sorry, what are the pebbles for? Do you cover them with the mortar base?

Excellent video! What are the exact mortars that you used in this video? I see you a variety of options, but I want to duplicate exactly your method with exactly which mortars that you used? I just purchased the mesh you recommended. Thank you!

What do you put at the bottom of the wall that will sit flush with the 1/2” Durocher board? Do you add more stock around the bottom of the wall?

Buena descripción de las herramientas,gracias.

Love your videos.im about to redue my bathroom and have learned so much from you.

I live in the metro area and I'm about to repair my shower pan. I'm so glad I found your videos. They are very explanatory and easy to follow.

Can i skip the mesh layer and just put the waterproof membrane on top of the dried mortar bed? It would be difficult for me to get the fiberglass mesh

Love your process. I will be watching more of your videos!! Thanks!

Really nice how to videos! Where are you based out of @simonproatl ?

Since we have the pre slope and the actual slope which leads to thicker concrete install on the base of the shower, my question is that how tall the step at the door will be good enough to prevent water running out?

I am talking the heigh/thickness of the concrete at the drain

hi all, can anyone tell me how thick of the concrete do we need to install after we lay down the liner? or how thick of the concrete do we need to install before and after the liner? Appreciate

I wanted to see how you do the walls. Do they touch the floor of the shower pan?

Simon why arent you measuring how much water is needed for 50lb ?

Good video! Thank you

Thanks for showing us the simple basics without making it seem more complicated than it actually is.

Is there any liquid fails that works?

I suspect my shower drain has no U trap below it becuase it constantly smells. It goes up through concrete slab like this. What can I do about it?

Nice information and video. What model and brand laser are you using.

Ok I think I did this wrong 😭. My basement shower was stubbed in. I poured the mortar already and thought I was supposed to cut the drain pipe and fit the drain fitting after the mortar dried. What do I do now?!

Would this OATEY pan liner and glue be AQUARIUM SAFE ? can i make an aquarium seal out of these materials seen here ?

How do you make a curbless shower on a concrete slab

Excellent video, help me a lot thanks, 👍👍

Last shower i did, i did not use any rubber liner. I built my curb (wood, cement board, then thinset and mesh to fill out, smooth and make uniform) and preslope. After which i coated the curb and pan with Red guard 3 times (same thing as aqua defense except Red) After that i put my final slope, coated everything in RG again and then tiled over that. Hopefully that made sense. This was all done over a concrete slab.

ur the best @simonproatl , quick question, what if i want to install a shower door on the curb would i still angle everything towards the pan? or would i want the curb to be flat and level?

Thanks for the great video! My 2inch ABS riser coming through the concrete floor is not perfectly vertical. A typical ABS welded connection to that pipe would end up with an 1/8 inch deflection from horizontal at the drain surface :( ..is there a solution other than jack hammering there entire area to replace the U trap and riser?

THANK YOU for making this video, it’s so helpful and specific for my project.

keep them coming.... so anyone of these mixed bags will work, theres no better one? I see in all your videos you use the Sakrete 50 lb. Floor Mud Mortar, but home depot is out of stock everywhere in my area, but they have the sand topping mix, are they equally the same or should I look for the sakrete one instead? maybe lowes has it?

homedepot is out of stock for the SAKRETE 50 lb. Floor Mud Mortar, which other one do you recommend? I like your videos, I am about to do your concrete curb this week, next is the pre slope bed... just dont know which mix to use... thanks!