Відео

viper shift gate install on a pro S

Are you still using the factor cp3?

👌🏾🍻

You probably don’t remember off the top of your head the center of hole to center of hole between the rear cab mount and front bed mount?! Struggling to source a diagram or measurements. Great video still very helpful with my Tacoma and 4Runner frame restorations

Looks great

So why can't you just keep the cylinder assembled? Use the cylinder end eye bolt to hold that end. Use the preload adjustment wrench to hold the rod end cap and screw the new eye bolt in until it hits the preload stop inside (the washer thing with flat spots). I'm gonna try my way and see if it works. 😂

Hey good afternoon I’m looking to install some bigger injectors on my truck trying to figure out up to what size I can install without any tuning

Only haters would pick on this. That fitment looks awesome! I have double tube Jeep bumper custom fab and welded onto my 04 and it looks great. Also I think you should continue with the wrap-arounds based on what you already have!

So you don’t need to take the bed off to weld the top part of the plate? I have the kit just bought my welder. Gonna do my 98 Tacoma soon.

Great work awesome Rig do you have a clutch kit for those 35', if so would you do a vlog on that really appreciate it keep up the great work....😎🤙😎🤙😎🤙😎🤙😎

The front camera can pivot around a bit . Move the front camera around a bit !

Awesome I'm the process of doing the exact same thing to my 2004 double cab

Awesome video. I’m going to replace both on my 2003 Toyota Tacoma extended cab (Access Cab who knows whatever is call .

🔥

got you to 1000, buddy keep it up

I need one of those jacks

install a short shifter it really helps

Good video lad well done

How do or did you like that B/R Trailer??

Great job right up to the rubberized undercoating which will fail, hold salt under it and rot the new frame in record time.........Never ever use rubberized undercoating, use only wet oil based products if you want to protect your vehicle......

Do u need to have a title and plate on the rv also or the gooseneck trailer is enough ????

Sweet rig what’s the wheel base and belly height ?

It’s a nice house

What’s your wheel setup? Offset, backspacing, width?

Absolute pain in the butt of a job, just did mine today. The engineers at polaris should be fired immediately! Zero reasoning for that to not be much more easily accessible!

Hello, where are you located and what is a good way to contact you?

Just sold my XP with 4100 miles

did you end up tuning it when you put the injectors in? Planning on doing 45 over on mine but not gonna retune it for a little bit until i can get efi live. Have h&s minimax now.

One more subscriber! Nice work, what did you put on the inside of the new piece of metal? How long will you think this fix will last?

upgrade your 1st Gen Tacoma door handles with Trubuilt Tacoma Metal Handles for durable replacements!

Ten years in my door handle broke just like yours on my 2001 Tacoma. My fix - baling wire. All you need is about 5 inch length of baling wire. Drill two 1/8 inch holes from the outside handle part through the inside handle part. Run the wire through both holes and twist the wire with your fence pliers. Clip off the excess wire. 13 years later still working great. I left the wire a little long. Makes for a great anti-car jacking device. Anyone trying to grab the handle quickly to jack my car is going to get shredded fingers.

Hey Jr! Nice to see ur bike build. Havnt seen ya since the wedding

i have toyota hilux 2011 is posble i use axle 1 ton mi trock is 4 cilinder turbo diesel

can you cancel the start up logo, or does it come on every time you start the car, isn't that annoying?

ua-cam.com/video/m3lg8X-IKP4/v-deo.htmlsi=B4XJ_PLI6X_rVsBE This video explains how to get manual window crank out for those of y’all with crank up windows

What gear are you using and what did it cost

It took 2 minutes to open the door...to began the job.. Thanks anyway.

When putting them back on the bike make sure to use grade 8 bolts... ask me how I know...

I had a long bed like that for a long time. Rebuilt the trans and motor, went through that thing until the wiring went. Got my eye on a short bed lawn ornament and darn it, this video made me put in an offer.😢

Do you think I could wire a cigarette plug to the end. And charge when needed. I have way too many wires running down my bars

Any reason or rhyme for OEM??

I shot you an email on that Tacoma rust!

What’s the part number for the PSC hydro assist kit you used

Thanks for the vid.....I've had to do the driver side handle twice now.

Great build. Awesome idea for my Jayco Baja

Where are you located? I have some rust on my 04 Tacoma that needs to be taken care of and I can't find a place around Denver that does that sort of thing.

I know its been a while, but do you remember how you got those side panels back in? I'm having a heck of a time with that. I can get them close but it seems like something up front is in the way of a flush fit. I also have no freaking clue how I'm supposed to get that led popped back in, I can't get my hand anywhere near that.

I know its been a while, but to get the front seats out you have to undo the 4 bottom buckles. Then the belts will just through the holes in the seat. Fat pain with 1 person, not bad with 2. You need both hands to hold the springs down to have somone else easily pull the belt out.

I replaced and now a year later I have to replace again. This time spent the $$ on it over 130 bucks. Broke the second time opening the door.

I know what the next project is I think