Відео

What is the inlet diameter? Not mentioned on the ali site

They look good. A mate has some carbon ones on his Monster, they lasting well and sound great...

i love this bike! magnificent!

Good detailed analysis. Proving the plugs with OHMS testing was a good learning and testing after drying them out also. I expected them to come up fine once they dried out, but no...... What kills plugs?

Were you able to refit the tail piece etc? Build quality? Cost?

what i wanted you to remove is that piece of plastic on the other side of the brushes. i dont know how to get it off

Always out for me!!! My Multi has Staintune with baffles out, sounds great for an ugly duck......... Got termis on the 749...

Nice just leave the baffles out sounds awesome

Silly question. Do both drain plugs have crush washers/gaskets?

Looks good bro!

Good to do stuff yourself, but I think I just going to drop mine in the workshop when that time comes....... Good to know about the fuses tho..... Cheers!

Thank you

Yeah. I need to pop open both of my XBoxes open and take a look. They are working fine at the moment. I suspect the Halo XBox I have has one of the gold capacitors that doesn't need to be replaced.

Yeah they look good alright, Not sure whether to go for the Red or the Black THB....................

Thanks for this video. I found two bad coil packs on mine.

Is it available for a 4th of July party?

Those things were sooooo heavy. And the slush box trans kept then very sedate.

Love vids like this. Cheers!

what is the pin number for the tach?

it started playing again will do more videos on it later

How has this rebuild kit held up since? Trying to decide whether or not to rebuild or just go 1098 cuz that's a direct bolt up and from what I understand a better design.

Sounds like PSU problem.....its not providing the correct output voltages.

Thank you for the videos. Did you replace the cups with new? And what was the issues you had before cleaning the valve body out.

Soooo., a year after watching it the first time it doesn’t look any easier. Think I’ll get my sister’s 5 year old to reach in through the ram air inlets and clean mine lol😂

Love you videos bro

Link for W203 Diagram.Thanks

Hello my friend Chanel is good .valvule Electric tape solenoid?

So, that is pretty close to F.

Hood ornament is better

Promo'SM 😳

Sound good👏🏼

You are removing the regulator. Not the brushes 🙈

Thanks Mike..

sounds like sh*t

Good work , my advice though , crack open the oil filter housing first , as this releases more oil to the sump.

One of the more dumber tutorials ive watched what a complete waste of time

Where do the fuel vent hoses connect to? Mine have been replaced and messed with. I have a rubber hose coming off the intake near the engine and it’s been wrapped with wire tape. Do both of them connect there?

Speak up, you're talking to yourself instead of projecting to the viewer. Say what you're going to do instead of wandering around.

Guten Morgen, Glück, Hoffnung und Optimismus ❤❤❤❤❤❤❤

what is your cleaning product when you soak it??? Thank you

Just got a 50 roadmaster riviera

What is the antenna type is using to this card? RP-SMA or SMA ?

Nice job on the tool. I made a similar tool from a sheet of alloy and an old intermediate plate. I cut the slots for the basket and just bolted the intermediate plate in position. Saved me having to file all the lugs on the inside.

THANKS FOR POSTING!! Great information!

How do I fix Frisbee that been kut

A beautifully styled car with a venerable engine which I'm glad to see some folks still appreciate! BTW, is that a 3/4 race cam?

Your video was very well made 👏 thank you

didnt know there so many differences with the latches, I always thought its a simple swap

very nice and calm work. i enjoyed watching it!

And I thought Ohlins were hard enough to do. What a Vag of a job! Good work tho!