Відео

@ucaldavidson8643 Thanks I appreciate it 🙏

@@richardsutton1161 Thanks and I'm grateful that you like the video. And I will demonstrate / dismantle on how the size 4 magnetic motor starter look very soon.

@@thurm101 Appreciate it 👍

@@moinquazi9588 To be honest I have never done that, nor never seen any videos on UA-cam on how to replace the heating element. What I normally do is if I have similar iron which is a donor i would used that sole plate that already has a good element.

@@ashrafelsery6666 Thanks I appreciate it.

@@dharshandharshini0912 Thanks

Thanks alot and I appreciate it 🙏

Thanks bro appreciate it alot 👍

Connecting the wire straight and removing the thermal fuse out of the circuit it will works. But I don't recommend for you to do that, because it's not safe. It's a reason why if you to have a power surge and the fuse is missing from the circuit you can cause damage. I will leave a link to a vedio on a fan that has the similarity on what you asked.

ua-cam.com/video/OJ1AWbpTcIk/v-deo.htmlsi=f1ovvA6zZLaFCle0 you can click that link and it will carry to one of my videos similar to your question. And remember it's not safe to have the thermal fuse to remove from the circuit.

Thanks and I appreciate it alot.

Thanks much I appreciate for the feedback. It was a motor car with their sound system across from where I was.

Great to know, thanks and I appreciate it 👍

It's a Drill Master 4½ angle grinder

This is the link on the angle grinder ua-cam.com/video/u1gWaH3qIb4/v-deo.htmlsi=PnBIfene62MfeXp1

Your welcome

Thanks appreciate it and your welcome.

You can used a plastic scraper or a plastic spudger to raise the film off the mirror. And from their you can just Peel off the film.

Your welcome 👍, and am happy this video was helpful.

Thanks much I appreciate it 👍

Respect 👍

The breaker rating is known, with this test it indicates to me if the breaker can manage any additional load.

Thanks I appreciate it

Thanks

Thanks alot 👍

You just have to get a very thin screwdriver underneath the bitten button and pry it straight up

Thanks I appreciate it.

Your welcome this is the name of the fuse that you can look up on Amazon anytime your ready to purchase. BOJACK-Thermal-Degrees-Celsius-Cutoffs 240⁰c 250v 10a

I was looking for vedios on UA-cam to see if their anyone who have done any repairs on the model. Haven't seen any base on how the iron design I can guide you step by step

The two buttons on top, one controls to spray water and the other for steam. Push down anyone of them and the one that's not push down used a flat head screwdriver to prise that one out and do the same to the other one. After carefully remove those two a screw should be their

The knob that you used to adjust the temperature of the iron spind the non to the direction when your turning it off. Used the same flat head screwdriver and carefully prise it under the knob to remove it but be careful. Check to see if screws are their, also after removing the knob their should be a plastic thing with a small spring on it that give a clicking sound when turning the knob don't lose that

Let me know how far you reach just a question you did use a multimeter to check the iron cord it self first right

Thanks for reaching out to me. With the model specification I can do some reach and guide how to disassemble it. Pertaining the parts I got them from other irons and the thermal fuse I buy those on Amazon.

@CarltonMarshall Thanks appreciate it 👍

@justinemulenga4405 Thanks I appreciate it and your also welcome 👍

@omarjames1523 Thanks and I appreciate it alot 👍

@MultifunctionKaTech Your welcome

Good day Mr Mario, can you give me the specifications on the device including the model number and name of it as well. So that I can get diagram and give you a feed back as in how to troubleshoot and fine where the fault is.

@@IshiTechtronics2570 Thank you very much for your help and collaboration, what other measurements do you recommend I take? Because I can't find the problem, apart from all the values, measurements that I already made as I tell you, I tried to change the boiler anyway, I put one again to see if it was solved but no, I put it full of water, turned it on and what happened is that it heated up without cutting until it reached such a temperature and steam pressure that the steam overpressure valve ended up jumping to release so much pressure, As soon as that happened I hit the turn off button and at that exact moment the light in the house went out again.

@@IshiTechtronics2570 The ironing center is Bosch sensixx Ds38, TDS38311ES/01

Thanks much for the information, I will give you a feed back as soon as possible.

@@Mario14792 Good day I have found the brand iron on google but no diagram. But I was able to fine the manual for it that till how to troubleshoot it. And also I even found on UA-cam channel with someone actually have one doing trouble shooting. Its possible for me to send you the links on both so you have a look at it.