Відео

There are many different controllers to be honest, I'd say if you know what you are doing you can pretty much make anything work. Does yours have the blue loop connected wire? Normally this is your limiter I normally connect a switch to this so I can bounce between the two.

@@russsayscut437 that’s what I wanted to do but it doesn’t seem to have one . The scooter is just a cheap Chinese copy I picked up to mod myself. Can’t change firmware on controller and the settings in the app are very limited so looking at upgrading the controller first. Added front suspension, the rear is on the way. These solid tyres are murder over bumps with no suspension. Thinking of Goin a big bigger with the 8.5 inch wheels as well . I’ve raised the handlebars about 5 inches and put some handlebars off a stunt scooter on as they’re wider

@@russsayscut437 I’d love a ecu but they’re just too expensive atm

😂 duck head is a new one. Did you manage to fix it?

couldn't get it to fit in the end, so had to go with rear disc only. the only way around it is widen the top fork

Thank you @HashirEasa 🤙 something didn't feel right having the number 666 attached to me 😁

@@russsayscut437 haha youre welcome

Thank you 🤙

Hey, it's just a rim from eBay, I think I paid about £180 for it

Thank you, I always so we did well for what we had to make it (no money, no actors and a 8 minute script) we was learning as we went on and I'm proud of it and everyone that helped make it.

apologies for the late reply, it's been so long since I watched this I can't remember what the issue was I'll rewatch and get back to you. if yours is say ECU I'd say you have an issue with the controller?

this was a fiberglass tank from eBay, I think I have one left I have used yet along with a frame and bobber seat

smart ain't it, really looks cool with satin black forks and seat

Thank you

as far as I know they do yes, all the ones I have built have the holes to add disc brakes. good luck with the build

nice one Maz, appreciated the kind words 🤙 good luck with the builds

that's a perfect name🤙

cheers dude, its a cool ride 🤙

unfortunately I could get it on the wheel but not the forks, you'd have to move the brackets on the forks for this to work. I did plan to build my next bike with wider forks and fit the same size wheel that's on the back to the front but haven't had the time to start anything else.

@@russsayscut437 Since I wrote that, Grin cycles came up with a spacer & washer kit to adjust the disk and and axel mounts. I also found somewhere that you could file down the back of the caliper as well without weakening anything. I finally got all the parts, I will update once I get them all together.

that's awesome, look forward to seeing it when it's done 👍

@@russsayscut437 Grin has the annoying habit of coming out with parts just after I bought the last generation. Not only did they come out with a disk spacer kit after I collected the parts from all over, they just came out with a great upgrade to their torque arms. More delays.

Thank you and Thanks for watching

Thank you for watching 🤙

I made it and had it printed by a friend

I've painted a few things with it now and I'm really impressed, I've tested it on a bike frame and then painted over the top with a different colour and it works well and looks really good. 😂 yes good idea, it's super sticky. I should of used cardboard on the floor 😬 wear long sleeves and definitely a mask as it gets everywhere. good luck with the bike 🤙

nice one that sounds epic. good idea with the laptop batteries 🤙 there is more videos on this channel how we got the front forks welded

I will have a look for the fork welding video. I have a stick welder and a flux core wire mig welder. Welding is simple if you follow the basic rules. All the best. Looking forward to the next pub crawl you do with your Missus 😂👍

🤣 Yes, the pub crawl is planned again this year, they have added more two more pubs so it should be even more fun 🤣

Thank you that means a lot, I do put a load of time and effort into making these videos and love doing them, if I'm honest lately I have been a little disheartened about the lack of views, to the point where I may just let the channel go and concentrate on something else, I think a lot of it is my own fault as I don't just do one thing and have loads of different things going on and UA-cam like you to stick to one subject but that's not me, I am creative and like to document it. as for the box (I was going to make a video) I basically take a photo of the box, measure it then upload it to Photoshop where I design the artwork, I then transfer it to illustrator where I make a cut file for my measurements and have them printed off on vinyl. hope that helps, Thank you for watching 🤙

@@russsayscut437 Awesome! I would love to watch a video on that. I am trying to make a custom Red Dead Redemption box. I really like that you use stickers as opposed to just paper. Would you mind if I asked for your email address to further discuss the process?

I'll add it to my to-do list as it is interesting and kind of cool. I'm on the Instagram @russsayscut if you need to contact me outside here 🤙

Thank you that means a lot, it was a great project to work on and we had a blast making it. it was a massive learning curve but what we had to make it we did a good job. thanks for watching

Cheers dude 🤙 I'm 6ft 3"

@@russsayscut437 M'y pleasure, thanks 🤘

10 points, yes it's an XL frame, I have another one but not sure if I'll build it?

Thank you for the kind words. the original idea for the film was to make a 10 minute short film about Matt going to prison, Meeting Norman and learning how to box with a boxing fight when he got out, it quickly turned into a much longer project as Matt knows everyone and they all wanted to be part of it which was great but it still had to make sense which become the challenge, I didn't just was random characters in that didn't make sense to the story so it was an on going battle to keep the story following. with what we had to make it with and the fact it was the second film I'd done with no money it turned out really well and I'm proud of what we did.

Thank you for the kind words it was a massive learning curve and very difficult to put off with no money or experience but it was great fun and loved every minute of it

Thank you for the kind words, it took a long time to make and we learnt as we went, with no money so I'm proud of what we all did.

No London mate he was the governor

Thank you dude and thanks for watching 🤙

Thank you for watching 🤙 yes Matt is a great guy and a true gentleman, he was nice enough to let me base this film on him, it took 3 and a half years to make and was a great learning curve. for what we had to make it it turned out well

cheers dude I'm really pleased with how this bike has turned out 🤙

I was impressed I got that as it's only a 250watt motor, it has been limited now to 15.5mph to be legal 🙄 thanks for watching dude

thank you for watching 🤙

I made them using Photoshop and Illustrator then had them printed on vinyl

@@russsayscut437 is there a specific template?

@@russsayscut437 if theres no template can you give a tutorial!!

There is as the front of each box is slightly definitely due to the over hang on the funko image. yes of course I can that's a great idea. watch this space and thanks for watching 🤙

@@russsayscut437 Cant wait for the tutorial! thank you definitely subscribing 👍

Thank you for the info 🤙 I did see on the display you can tell the controller if it's 4,8,12 magnets on the disc which I did change to what mine was but I think I will put the original disc back on and see if that fixes the issue 🤞 thanks for watching

The ape hangers 😁 I liked them at first then thought they looked a bit odd, I think I might of thrown them away 😬 sorry. thanks for watching 🤙

From eBay dude, all the parts on this bike was from eBay. thanks for watching 🤙

But you built your own rear disc brake bracket! That's what I need desperately to finish my build. I've tried all the machine shops around here and know one want to waste their time.

The bracket was from eBay too ill try and dig out the you

@@russsayscut437 thanx Russ I've been want so much to get my bike rolling agian, I've invested alot ofmoney and time,and all that is left is the darn back brakes! I have 2 -1000watt motors,1000 on the front hub. With disc brakes and a 1000watt rear hub motor, 2 52volt 20 Amp hour batteries. And last year I ran into my back disc brake problem. I can't trust occ's back pull brakes, so my bike has sat motionless for a whole year now, and machinist to help. So if you can help I would be in your debt!

your very welcome dude www.ebay.co.uk/itm/374173537615?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=o8fhlpmws8q&sssrc=2349624&ssuid=t6dbtmles46&var=&widget_ver=artemis&media=WHATS_APP

Thank you and thank you for watching 🤙

Thank you Kevin, we did well for what we had to make it. thanks for watching