Відео

@@wedsoneler6735 imgbb.com/MGYFDk8

Почему бы и нет, есть даже идея - дуэт поющих 303-х

@@ChibikR У меня тоже есть TD-3😊

You need to add new btnpressed variable, setup another pin with pinMode and duplicate if else statement but for new variable and pin, where you can change to different note

@@ChibikR oh cool. so just duplicate that for each pin i want to add! awesome! i can’t wait to get it all together this weekend

This board is called digispark and connected with usb, it has version with preprogrammed micronucleous bootloader on to a attiny85, there are smt and tht version. In my case i programmed bootloader on to a empty attiny85 and insert it in this tht board. I used arduino ide and you can add more sensor with no problem up to a 5 (6 with disabled reset pin, but that solution disable low voltage programming of attiny85), but attiny85 is limited for number of pins. Arduino pro micro with atmega32u4 can be more suitable solution for a bigger controller, and there is ttp229 which can provide up to 16 touch sensor button with specific protocol, but i tried to use it with no luck(

Yes, i will send link for it later, when i turn on pc

@@ChibikR thank you so much. i can’t wait to see it. this is so cool

@@eross21 telegra.ph/DigiSpark-usb-midi-05-23 if you have more questions, feel free to ask

did you program this through arduino ide? i cant find a board in the board manager to program it to

@@eross21 Hi! You need to add url link for a digistump board in arduino ide. You can check this video for installation instructions ua-cam.com/video/JGf6P52LO5c/v-deo.html

Hi! Thanks! I didn't put any additional resistor or capacitor, just touch module connected to a attiny85 pin. For pc connectivity and usb midi i use digispark. If you have sensitivity problems with touch module you can solder small cap around 1-20pf on empty pads, it may help with this problem and decrease sensitivity

Yes, TD3 with valhalla supermassive vst, no multitracking, recorded live

Show us how you build the sound from ground up then

@@thorsoundsystem-doct6103 ua-cam.com/video/YrEDeIvb5fA/v-deo.html

Unfortunately, this is only demo. I didn't finish it :(

@@ChibikR bruh jump on that, shit was lit!

Behringer goes through valhalla supermassive effect vst, no additional synths were used, all sounds from behringer, no multitracking or layering, only one track

I use valhalla supermassive vst, it gives beautiful width to any instruments

Congratulations on your purchase! I think you won't be disappointed)

@@ChibikR This was the sauce I needed! Thanks 👍

Thanks! Yes, i use valhalla supermassive

On original it has sound output, but uses connectors that looks like banana, i replaced it with 3.5 mm jack and also give it ability to disable speaker when you insert cable

That's very cool ! I'm looking for one with a jack output too but it's hard to find at a reasonable price@@ChibikR

If possible, you can check russian ebay called "avito", here faemi is not so rare. Btw, faemi also have three generations: 1970s with germanium transistors, 1980s with silicon transistors and late 1980s-early 1990s with ic. Mine is germanium one

Hi! I forgot sequence, but i don't delete it from td-3. I'll check notes and post here

D# F#up D#up Bup F#up D# F#up D#up

Если я не ошибаюсь, каждая риска это 20 бпм, но конкретно в этом джеме я синхрозировал с daw

@@ChibikRСпасибо

Unfortunately this was only demo, I abandoned this track and didn't finish it. But you can find tracks with simmilar style made by me on Spotify, type ChibikR

Valhalla Super Massive vst

Which daw do you use?

Hi! Thanks! On my channel you can find video called "How I make Berlin School on Behringer TD-3" in which i showed how i program td3

for drums and fx i used daw and synced td-3 to it

thank you, good luck@@ChibikR

Thanks! I can send you schematic, because how you can see on video it's just prototype for now

ibb.co/MGYFDk8

ありがとう！

Which daw do you use?

Thanks, i recorded into FL studio and run td3 through Valhalla Super Massive vst

Valhalla Super Massive vst