- 70
- 64 242
College of Western Idaho Welding
Приєднався 16 тра 2018
WEMF 101 Week 12 Keeping Your Work Environment Safe
In this week's lesson we will talk about general ways to keep the workplace safe, including housekeeping, confined spaces, and ladder safety.
Переглядів: 51
Відео
WEMF 101 Week 11 General Health Protection
Переглядів 472 роки тому
In this week's lesson we will discuss general ways to protect our health in the workplace.
WEMF 101 Week 10 Fire Safety
Переглядів 682 роки тому
In this week's lesson we will discuss fire safety in the workplace.
WEMF 101 Week 8 Electrical Safety
Переглядів 532 роки тому
In this lesson we will discuss basic electrical theory and the hazards related to electricity.
WEMF 101 Week 9 Electrical Grounding and Electrical Tool Safety
Переглядів 782 роки тому
This week's lesson covers the purpose and importance of electrical grounding and safety features incorporated into modern hand tools.
WEMF 101 Week 7 Machine Guarding and Lockout/Tagout
Переглядів 543 роки тому
Week 7 lesson regarding machine guarding and lockout/tagout proceedures
WEMF 101 Safety and Leadership Week 6 Material Handling
Переглядів 583 роки тому
In this week 6 lesson we will discuss safe material handling related to the welding trade.
WEMF 101 Safety and Leadership Week 3
Переглядів 1013 роки тому
Week 3 PowerPoint overview of Personal Protective Equipment (PPE) related to welding.
WEMF 101 Safety and Leadership Week 2
Переглядів 1073 роки тому
This week will cover the formation of OSHA, dealing with safety in the workplace, and the roles of NIOSH, ANSI, and the EPA related to OSHA.
WEMF 101 Safety Week 1
Переглядів 2073 роки тому
This is the week 1 video for WEMF 101, Safety and Leadership.
24 Class Assignment 10 Part 2
Переглядів 705 років тому
Part 2 of the round taper flush to one side picks up where Part 1 left off. We have all the information in the front view to develop the flat pattern. The part will be ready to build at the end of the video.
23 Class Assignment 10 Part 1
Переглядів 695 років тому
Now that we have experienced a round taper that is equal, lets draw a round taper (cone) that is straight on one side; or flush to one side. Part 1 sets up the drawing and shows a nice little hack to get all the "true length" information in the front view alone. An explanation for how this hack works takes up the last half of the video.
21 Class Assignment 9 Part 1
Переглядів 625 років тому
This the the first Radial Line Development drawing we have done. It is a Cone (Round Taper) that is concentric. Part 1 shows how simple this type of drawings are, however there can be some drawing error if we aren't careful to keep in mind the actual circumference we want to end up with.
22 Class Assignment 9 Part 2
Переглядів 515 років тому
Part 2 of the Cone (Round Taper) drawing explains that we can be more accurate with our flat patterns if we consider the actual circumference of what we are drawing.
Hello, how are you? I have a problem with arcon welding. Impure puzzles. How to solve?
You are the only one who help my in final exam, thanks 🫡🤍
Great lecture
I have a 3” boat trailer tongue. I want to extend it 32”. I suppose I will butt weld the new 32” length of 3” tube onto end of existing 3” tongue tube. Then I want to slip a 3-1/2” sleeve over that welded and ground joint and I will weld the seam between 3-1/2” and 3” on either end. To add more strength, I was thinking about drilling several 1/2” holes in the 3-1/2” sleeve and then plug welding to the 3” tongue. I only think I need to do these plugs on the top so just flat welding. I don’t think I need to do these on sides (vertical welding) or underneath (overhead welding). Anywhere I am welding to the existing galvanized steel tongue I will use muriatic and clean off the zinc before welding. I am planning to use flux core mig machine. I think I will make a pass all around the plug diameter and chip off slag and then add more filler until I fill the hole. What is your opinion of this? You think flux core mig is ok process? Do you think starting and stoping to remove slag is right process or should I just fill and desalt after? 16:32 You think flat welding plugs up top is enough? You think 1/2” plug holes is big enough? (Tube is 3/16” wall). Am I missing something I should be doing? Trailer is for a 5,000 pound Boston Whaler boat. So not a big load but a precious one to me. Thanks for any and all advice from anyone reading this June of 2023.
This wasn't a proper application of straightness (according to the ASME GD&T standard). I suggest viewers to consult the standard.
0:11 iso is international organisation of standardisation not international standards of organisation
Thank you 😊
Dami kong natutunan! Thank you 😊 from PH
You're a lifesaver
Thank goodness for you help
Thank you sir. I've looked at 3 videos already and you hit the money.
very nice way of understanding sir thank you From India Mohd. rijwan welder
Appreciate
The iso's are more logic than AWS. But it is logic :)) I am from Europe
Iso for every other country it’s only the us that have there own standards
ua-cam.com/video/MYPIgqaxh0U/v-deo.html
Great Video following AWS Standards. Ideal welding for sheet stock or light gage plate as a useful detail for metal manual construction in welding. "I-Car" welding has a good application for plug welding. T J (Tom) Vanderloop, Author Instructor & Community Leader
Great video, thank you very much!
i need this to pass my blueprint test tomorrow
So other side and weld side are opposite for ISO.....??
yes :-D or, AWS is the opposite of ISO, depending from which side you look at it :-D
I am working on modification of quench tank which is almost 50 years old and probably its corroded so i was thinking to cut it down form one end so my question is how can we be sure that after cutting we will able to weld the end cap back
Thank you Sir
Thanks you so much for sharing such good information. Much respect!
This is a high quality informative video, presented in a very digestible way. Thank you!
Digestible hahha