Відео

@@alvingaming2230 D90, D99, D99s okkoma ekai. One ekakat hai krnna puluwn.

What do you mean by applying steering servo?

It's Hobbywing 1060 Quicrun 60A esc 😁

@@nirosharc podia por link

@@HugoLoureiro-m5n s.click.aliexpress.com/e/_DkmxFPb

CH3, CH4, CH5 and CH6 or to this controller ua-cam.com/video/yQgD09w_WAs/v-deo.html

@@aryan42162 Yes, I modified the interior by removing the partition between the two front seats to make room for the gearbox

@@PadminiMallika-fp6jc 2cell 2200mAh Lipo battery

Podia por link da bateria? Obrigado

​@@HugoLoureiro-m5nI bought it from a local store in Sri Lanka.

@@gayanbandara2851 Ow, Nthnm 5mm led okkoma 3mm led wlt replace krnna ona.

@@gayanbandara2851 Bullet connectors nam electronics kadwala thiyenwa. Xt60 connector ekath hodai.

@@nirosharc thanks bro,

Thank you!

@@nirosharc Hi there ! I have seen that many RC users just connect the LED lights for their RC without resistor (typically 3V).. while some add resistors. What do you recommend ? Appreciate you valued reply. Thanks

​@@newtonsmeter6239Hi, LEDs are designed to operate within a specific voltage and current range. If you connect them directly to a power source without a resistor, they can draw more current than they’re designed to handle, which can lead to overheating and eventual failure. Adding a resistor is a safer and more reliable practice to ensure that your LEDs function correctly and have a longer lifespan, Thank you.

@@CekasStory Thanks for watching ❤️

@@nirosharc you're welcome sir 🙏🏼🤝🔥

I think so.

Thanks for watching bro 😉❤️

😶👍

Stock Transmitter and receiverd?

s.click.aliexpress.com/e/_DmGG28H

what're you going split in half?

@@nirosharc The LED controller as in the video has 2 output poles, positive and negative. I want to use 1 positive and negative pole for 8 LED lights. and I use 1 positive pole and another negative pole for 7 LED lights. and I installed all the lights in parallel. Can I just use 2 resistors?

@@GarengPetruk I asked Chatgpt and it answered me like this:- Yes, you can use two resistors in this setup. One resistor for the 8 LEDs connected in parallel to the positive and negative poles, and another resistor for the 7 LEDs connected in parallel to the other positive and negative poles. Make sure to calculate the appropriate resistor values based on the forward voltage and current specifications of your LEDs to ensure they operate within their safe parameters.

@@nirosharc OK, I'll try it. Previously I used it without a resistor with 2 2 watt HPL lamps and 2 1 watt HPL lamps. Combined with standard LED lights, MN99s RC lights. and it turns on but after 4 days of me using it. My controller immediately caught fire. My controller is the same as yours.

Direct power from the receiver to the lights via an on/off switch.

2200mAh 7.4v 2cell Lipo Battery 🙂

Tnx bro. ❤

Yes it is.

Esc eken thama motor ekatai receiver ektai power eka denne battery eka haraha. facebook.com/nir0sha?mibextid=ZbWKwL

Direct power from the receiver to the led light bar via an on/off switch.

Not yet

You are welcome!

INJORA RC Car Winch CH3 Control Line:- s.click.aliexpress.com/e/_DloWgT5 AXSPEED Simulation Electric Winch Control Wireless:- s.click.aliexpress.com/e/_Dd3iZ95

Which color?

My pleasure ;)

Thanks 😁

Thanks for watching 😉

Description eke thiyenwa servo eke link eka.

Ow dala thiyenne, Servo eka nathuwa ywnna bane kohomath, Me servo eka thiyenne:- ua-cam.com/video/qv8d-93nvh0/v-deo.htmlfeature=shared

@@nirosharc remote ekak ganne kohomede 🥺

@@nirosharc ese , remote,servo motor okkotoma kiyak yaide

@@jayarathnawijethunga5752 Okkoma ona Dewal aliexpress eke thiyenwa. Price eka thiranaya wenne upgrade karana vidihe hatiyata.

Thanks brother 🙂❤️

ඔයාට ඕක full upgrade කරන්න කීයක් විතර ගයාද

@@jayarathnawijethunga5752 මට නම් දැනට 70k 80k විතර ගිහින් ඇති.

Drive shaft දෙකත් එක්ක එනවා Allen key එකක්.

@@nirosharc thanks

Much Thanks ❤️

•Connect the two wires of the motor to the two yellow and blue wires of the esc. •You can watch it in the 4:30 minute of the video below. ua-cam.com/video/VejCuznBj3s/v-deo.htmlfeature=shared

@@nirosharcthank you so much, but can I ask, where did you get those black and red wire? 😊

@@prince7p268 From the local electronics store. (16 AWG 200°c Heat Resistance wires and 2 bullet connectors)

@@nirosharc Thank you so much!

Hey ​@@nirosharc, can I ask what batteries are you using for this car? Thanks!

yes you can, But I recommend hobbywing 1080 esc for TRX4M.

Which one is cheaper

@@dua4436 Hobbywing 1060 is around 20$ and Hobby 1080 is around 40$. So, the cheaper one is Hobby 1060.

This is possibly with stock remote control?

@@dua4436 I don't know much about trx4m. But I think it will be possible.

Buy two 4.0mm male bullet connectors and solder it to the motor. Then connect the esc and motor wires together.

Thanks for watching bro:) monwad ona updates?

@@nirosharc ese and Receiver eki connect krn vidia Transmitter eke review ekk ✌️

Much Thanks aiya 😉🤙

•Max Nimh Volt Rating 10.8v / 9 cell •Max Lipo Volt Rating 11.1v / 3s So a bike battery is not possible, because it is 12v.

Thanks for watching bro 😉🤙

You're welcome.

It is the wire of the lights I made. Does direct current from the receiver to the light bar work? 1. Change the side of the wire clip and fix it. 2. Connect to another channel (ch4,ch5,ch6) 3. Check that both the transmitter and receiver are working properly.

To make it work you have to calibrate atleast 50% (ch3 dumbo rc) or use ch5,6

Hi, can you explain more please?​@@atlasvltor7260