Відео

Hi Mariano thanks for visiting my channel not really a problem the unit is ceiling mounted at about 3.5 m any air bourne dust is pulled in quite quickly and cleaned via the filters it works quite well thanks again cheers Michael

Hi thanks for visiting my channel both companies make quality products but when using both boards on a CNC machine I have found the finsa chips a lot less than the egger therefore I would always use finsa cheers Michael

Hi thanks for visiting my channel yes I do please leave an email address in the comments and I will send them to you cheers Michael

Hi Michael thank you visiting my channel if you leave an email address in the comments I will send a set of plans cheers Michael

I think he means the remote in your hand at 6:36.

Hi Johan thank you for visiting my channel. It's approx 11 X 11 m. Take care Michael

Thank you! Is that including the spray room?

Hi Johan yes that includes the spray room Cheers Michael

Thank you for your kind comment

Hi Earl thank you for visiting my channel appreciate it

Hi Roy thank you for visiting my channel and your comment. The distance I have front to back is about 24'9" and it needs most of this space to operate the sliding table. There needs to be sufficient room to allow the table to fully slide back to change the blade. I only use 8 X 4 sheets larger is possible but need more handling. I bought my table saw before my CNC machine. But if had known then what I know now I would of bought a smaller table saw as I do most of my sheet cutting on the CNC. The table saw takes up a lot of space. Hope the helps cheers Michael

Hi Barnes thank you for visiting my channel and your kind comment much appreciated

Thank you very much appreciate the comment new video next week on a shop upgrade

Hi Ryan thanks for visiting my channel. Yes go for it in sure it will look great thanks again cheers Michael

Hi Jim thanks for visiting my channel. Lol it might look that way but I'm in the workshop sometimes 7 days a week and it can get quite messy. Your welcome to view some of my many videos to see what I get up to. Lots of hand cream is the trick. Thanks again Cheers Michael

Thanks again for leaving a comment. It's all about confidence and I'm not there yet with that one to present or provide commentary. I do provide as many explanatory notes as possible to explain what I'm doing at each point of the video. I don't display notes if it's obvious what I'm doing eg sanding as I assume most people watching have a understanding of the various processes. I did do a lot of research to determine the format of the channel and I notice quite a few comments on other channels to drop the commentary and music as the viewer would rather watch. I know a couple of UA-camrs who did a lot of commentary on their videos to later started to produce videos with no commentary. So I opted for this format. It's suits me at the minute. Thanks again for stopping by. Cheers Michael

Thank you for visiting my channel and your kind comment

@@arbordesigns2514 My pleasure & thank you for writing back, not many do 👍👍👍

Hi Andrew thank you for visiting my channel. At the time when making the video I didn't have a leather strop but have ordered one since i will try it on the next sharpening session. Thank you for the suggestion. Take care Michael

Thank you for visiting my channel and your kind comment

Thank you for visiting my channel and your kind comment

Hi Gregory thank you for your comment. You could be right I don't know but most likely the low number of subscribers at this time is due to the channel being quite young. I will keep uploading videos up and see what happens. Thanks again cheers Michael.

Thank your visiting my channel

Hi Jason thank you for visiting my channel and your comment cheers Michael

@@arbordesigns2514 peace be with you.

Hi Kelvin thank you for visiting my channel. Yes more videos on the way thanks again cheers Michael

Thank you for visiting my channel. Lol

Thank you for visiting my channel. Lol

Thanks for that it's called Rubio great product thanks again for stopping by

Thank you

Thank you for visiting my channel and your kind comment

Hi Mark thank you for visiting my channel and your kind comment much appreciated

Thank you for your kind comment.

Hi Bob thanks for visiting my channel. Lol Not sure don't want to mess it up

Hi Richard thank you for visiting my channel. The workshop is about 100 sq meters plus I have office space and some storage. I think if it was any bigger I would have more machines in it so I'm glad it's the size it is. Thanks again cheers Michael

Thank you for your kind comment

Thank you for your kind comment

Hi Leon thank you for visiting my channel. Yes the channel is moving quite slow but I know it takes time to get the subs up I have a bunch of new projects ready for editing and uploading. I will just keep putting them up there and see what happens. Thanks again cheers Michael

Hi James thanks for visiting my channel. I watch the video again and didn't see any green button. Is this comment on the correct video. Thanks again cheers Michael

I think he means the remote in your hand at 6:36.

Hi thank you for visiting my channel. Yes still happy with the sliding table saw however if I was cutting carcass components I usually use my CNC machine as it more accurate and easily repeatable thanks again

@@arbordesigns2514 Thank you for the reply. Now you have me wondering if the SCM sliders are accurate enough to mill up sheets of plywood for me. I need to retire my track saw method and find a more efficient way to do this. Thx

Would you ever do a video highlighting all of the uses for the slider table saw? Is that the 8.5’ sliding bed? Thx

Hi the SCM sliding saw is very accurate once set up and I would recommend it no problem I work in my shop alone and it's easier for me loading the CNC machine rather than the table saw. Yes I will maybe consider doing a video on my table saw let me have a think about it. In fact I might make videos on all my SCM machines it would be an interesting series thanks again cheers Michael

@@arbordesigns2514 okay, that sounds good. I’m looking at the Minimax SI 315 ES myself. Just subbed and would watch the series if you decide to do it. Is your slider the 8.5’ length bed? Thx again.

Hi Anthony thank you for visiting my channel. Yes it did and I have it connected to my main dust extractor. Hope this helps cheers

Thank you for your kind comment