- 37
- 37 430
Jesper Bergvall
Приєднався 5 жов 2011
Så här tänder jag min OONI FYRA pizzaugn
Har skaffat mig en OONI FYRA pelletseldad pizzaugn. Så här enkelt tänder jag den.
Переглядів: 352
Відео
HoverMower. Bonnet bumper test. No cutting.
Переглядів 954 роки тому
The bonnet is placed on three rubber stand witch allow for some movement when hitting an object witch triggers a switch. Unfortunately the skirt is too close to the ground and occasionally hits the grass and turns around.
HoverMower running uphill.
Переглядів 1344 роки тому
About 30 degree angle and no speed loss. sites.google.com/d/1po-rBfP18vJIZcp2wWZlMZtE47z5z0yA/p/1s2Aooq2XfoipvHHBaVfRkaYiznB4EcJp/edit
High grass bumpy terrain Wind noise
Переглядів 3824 роки тому
Got better traction with 3D-printed dubbs bolted to the rubber tires.
HoverMower high grass cutting test.
Переглядів 1004 роки тому
When cutter motor current increases the forward speed is reduced by 60%. If the current increases even more the mower do its obstacle routine by backing off and turn.
HoverMower, perimeter wire test.
Переглядів 1,2 тис.4 роки тому
Testing the invisible fens, perimeter wire from the Ardumower project and drive chain from a hoverboard with modified firmware by NiklasFauth/EmanuelFeru. sites.google.com/view/hovermower wiki.ardumower.de/index.php?title=Hauptseite github.com/NiklasFauth/hoverboard-firmware-hack github.com/EmanuelFeru/hoverboard-firmware-hack-FOC
Analyzing NMEA2000 Network with Arduino
Переглядів 11 тис.5 років тому
Arduino code: github.com/ttlappalainen/NMEA2000 (Thanks Timo) CAN transceiver: Search on EBAY for SN65HVD230 3.3V I found the NMEAReader application on www.actisense.com
MSF 20170821 måndagssegling i Mariehamn
Переглядів 1947 років тому
MSF 20170821 måndagssegling i Mariehamn
Alvin flamberar äpplen på Smakbyn med Michael Björklund
Переглядів 1,4 тис.10 років тому
Alvin flamberar äpplen på Smakbyn med Michael Björklund
CNC milling the deck of a half Albin Express
Переглядів 45410 років тому
CNC milling the deck of a half Albin Express
Thanks for this helpful video. Just a question, you compiled that arduino code and then run actisense software and It works?
Yes, as far as I remember.
👍👍
Bra hunden var jätte fin
❤
👍🇸🇪❤️
Hey are ther any plans on how to make the perimiter wire
I'm working on using RTK GPS instead. But before that I was using the perimeter wire ideas from the Ardumower project. Search on that project.
@@jesperbergvall7714 ok thanks and what motor do you use because i use a brushless motor but it gets boged Down quite easely because i have to run it at low rpm do to nois but your motor seems to make almost no noise
@@racingturtel5002 I scraped my kids hoverboard and followed this guys instructions on how to use the electronics and wheels from it. github.com/EFeru/hoverboard-firmware-hack-SIN I use the constant speed setting. That way the mower have the same speed no matter if it's uphill, downhill or deep grass.
@@jesperbergvall7714 ok thanks very much
I wonder if nmea 2000 stream from this could be picked up by Timezero and shown there…?
If TZ accept standard NMEA2000 I don't see why it shouldn't.
Hi.. Send for me code in ardino
github.com/ttlappalainen/NMEA2000/blob/master/Examples/ActisenseListenerSender/ActisenseListenerSender.ino
What system are you using for navigation?
Some code was taken from the Ardumower project for detecting a perimeter wire. I, how ever, skip that idea and working on a solution with a RTK-GPS and G-code. I will post a video once I get it working a bit more satisfying.
Can you program actisense EMU-1 with this?
I have a interesting situation - I want to take N2K tank data and convert it to canbus J1939 - could this be done?
See the CX5003 china box. Everything is eazy if your senstor is "ISO".
@@TheFlybyman No fun in that!
Nice project. Can you write what motor do you use to turn cutting blades and what RPM do you use ?
Just some scrap I had laying in my garage. Don't know the rpm.
Ser kanon ut! Vad är det för 3d model du använder? Skulle själv vilja sitta på datorn och designa till min express och då vore det ju händigt om det redan fanns en model.
Fixade ihop en stl-fil med hjälp av programmet DelftShip och ritningarna på förbundets hemsida. Gjorde g-coden i Vectric Aspire.
@@jesperbergvall7714 Bra jobbat, skulle du vara okay att dela med dig av din stl så slipper jag generera den själv? Kommer konvertera den till Solidworks så om du är intresserad av det så kan jag skicka tillbaka den när den är konverterad.
Hi. Impressive. Possible to upload your hover firmware on your github? Can you show permiter sensor and wire connection? BR, Kris
Do you have schematic connections nmea2k to transceiver and transceiver to Arduino Due?
I more or less used the same schematics from this blog. sailboatinstruments.blogspot.com/2016/04/building-your-own-nmea-2000-device.html?m=1
Just bought it for my Nysted 17. The previous owner had lathered on the bottom paint way above the waterline and freehanded it :/ looks to be a good product this *thumbs up
Can you give more information about the can transceiver you have used?
Hi I used the SN65HVD230. Search for it on EBAY. :-)
Imponerande!!!!