Відео

I'm currently modifying a WLToys RC car to a robot and to me the performance at the lower end (up to 20% throttle) is the most important, because I don't want the robot to go so fast. I noticed that cheap ESC often have very low PWM frequency like just 1kHz, which produces a very loud whine and causes a huge power loss at the lower RPM range. Are there known brushed ESCs that go well past 10kHz PWM so it's not audible at low rpm? Since I don't know if anything better is available for that, I decided to design my own ESC with 40kHz PWM which should enable an extremely accurate and responsive control with good efficiency at low RPM range.

I can't for the life of me make the ball bearing go into the hub. I've reviewed the instructions multiple times and I can't see what im doing wrong. The ball bearing seems to be marginally bigger than the clearance in the hub. Did you have to do anything to make the bearing fit?

How do you think they will compare with Rlaarlo XTS-F10? (with or without their 190 mm conversion kit) 🙂

You said to put the tamiya logo facing the chassis and now I need to turn it around bc you said it wrong

This is really cool

do you have lc racing ptg-2r ? try comparing it with the xv-02.

la corona dentata nn esiste in metallo? ex real

la ruota dentata e materiale nylon .......nn esiste in metallo?

So they only go in front ? Is the rear different 🤔

Very impressive video, then I bought the R12S based on your video, but the size was not quite right, the aperture seemed larger than the TT02's 48mm. if you know how to figure it please let me know. Thanks a lot.

Novice here. Should the TT-02 get a 180 or 270 degree servo?

Just wanted to know where to plug the wires in. Everything up to the point you didn't mention any of it was pure idiocy.

Bro i have this one its pretty good for the price

Stock?

Thanks, looks super clean!

Woulda been neat to see the traxxas titan 12t in this

U can give one away right?

Thanks for the info, i am amazed i dont see anyone else doing thess kinds of in depth looks!

How about the original TT01 front and rear differential it will fit inside the gearbox?

correction, the G14L is a 14T is it not? hence the name.

I never realized they were that easy to adjust, I always thought you had to take the cap off.

Ok so,my tt-02 steering can be straight but after i turn left/right,it only turn straight a little bit..so whats the problem,the servo or the steering rack or the turnbuckles..my servo is the futaba s-u300 and if i only change the turnbuckles and just keep the stock one..can it be install?

Are any of these sensored ornsensorless motors?

& im shure swapping out the esc didnt make the model any cheeper😂 when they started coming with the tble i couldnt wait to get one but never ended up useing a bl moter with it back then a bl moter was the cost of the kit or more if i had any idea of the power at hand with bl i would have deff splurged but even hobby stores had no idea & the moter i was running back then i thought how could this weired looking washer moter be better come to find out Ya they make an incredable amount of power for the size 🤷‍♂️

Well that was a total waste of time? No binding.

So i can put jimny body in wild willy 2 chassis?

Is that Cal Raceway!

i think i would have put the body on the car/top of posts then measured the gap between the tire and wheel well arch with calipers then subtract the gap you want and add back how much you want sticking out the top then cut the posts down by that much.

New video from my favorite channel ❤

Great video but I still have to say, to start the project I take an ultra fine sharpie and mark all the cut lines on all the parts to be cut (on the over spray side of coarse), then proceed to cut and define shapes as desired then wash the inside thoroughly. Then take sharpie and define all lines needed to be masked. Because even with the best paint the stress you put on the plastic while cutting could scratch or chip the paint inside if cutting out after paint.

Tip, I like to use foil for mirror surfaces just cut the foil the size of the decals and simply use a child's glue stick to fasten to body scrap!!!!

I can see this is going to take awhile so I'll find a shorter video, thank's anyway.

Is this your first, just center the masks as best you can, the trim decals are very forgiving they'll hide the size difference!!!!!!

Formula E I’m thinking of getting one . Looks Amazing.

Great video how about the Titan 12-T

actually the driftech tires come with TT02D define its "driftable". it is 4WD, regular steering angle, no power lock or limited diff on rear gear. but the 02D kit comes with oil shock, full set of ball bearing, sport tuned motor and motor heat sink make 02D more valuable than regular TT02

Bro you made that so much harder than it needs to be lol tools for the sake of tools it looks like to me!

The best new rebuildable motor you can buy is the Tamiya super stock series (rz,tz,bz). They’re manufactured by Sagami in Japan. Sagami made motors for Orion, reedy, yokomo, and others back in the day.

its quite slow.. but still looks fun tbh

I tried 2 tble 04s esc’s and both lost reverse on their first runs and wouldn’t revert back to brushless after being used with brushed motors .

Ok if your using it for a rally car but for high speed track racing keep it stock plastic .

Great Thank

Can use stock controller?

Mine came with a broken suspension mount

Do you still have this car?

I have just built this chassis with the Mercedes CLK body , i found it to be a good quality build with plenty of shims to reduce the famous Tamiya slack !

Flower power