Відео

I had this message " Not all items are available for download at this time. Some items need further review. An email will be sent to you when you can access your pending downloads."

Need help with the program

if i want to buy the already made board from you, are you selling?

Thank you for posting the cool introduction to Visuino Pro! Please enjoy your license, and create many cool PLC projects! 🙂

Hi!!! I really love ScadaBR and openPLC, just few questions. I tried a simple network with just 3 slaves and ScadaBR as the master but did not work. Could you make an openPLC video with 3 slaves and ScadaBR as the master, please? (Arduino Modbus RTU Serial) How to configure the Modbus input registers %IX0.0, etc. and %IW0… in ScadaBR?, I tried but did not work. (Arduino Modbus RTU Serial) Coil Status and Holding registers are OK. Great Video btw!!!

Can i change the Arduino Nano with the Arduino Nano ESP32? I checked all the pin is same

In my case I want to connect an Arduino Nano using Modbus Serial with Scada In Touch

In my case I want to connect an Arduino Nano using Modbus Serial with Scada In Touch

In my case I want to connect an Arduino Nano using Modbus Serial with Scada In Touch

Can we bypass the In Touch license by using KEPserver? Great video by the way

Can we bypass the In Touch license by using KEPserver? Great video by the way

Can we bypass the In Touch license by using KEPserver? Great video by the way

I just realised that there is no 5V pin. How to I connect my VCC pin of PIR sensor to the Arduino PLC?

Can you give me block diagram of its if possible

Please write me your email I need to develop a PCB project for esp8266, 8 relays, 8 4-20ma inputs, 16 inputs via a shift register for a button and 16 5v outputs via a shift register, I would also like a built-in OLED display connected via 4 pins, could you design such a PCB for me?

thanks for this video, very informative, weekend tinkering planned

Thank you bro, can you give me the arduino code

Wow Amazing tutorial, I love how you display the relays state. Very nicely explained!

WIth the Pro version of Visuino you can use the Modbus functionality, and make the PLC compatible with industrial SCADA applications, and accessible over Modbus 🙂

Wow! Thank you! Very cool, and simple to follow video 🙂.

Great!!!

Cool!!!

Hello, thank you once again in this way for what you do. I learned a lot from you and I am very passionate about this. I have a big request for you. I saw an older clip of yours "How to Install OpenPLC Runtime on Raspberry Pi || Pi PLC" and I also tried to do it with raspberry pi5 and it doesn't work. I took PI5 because I said it was the last option and anyway always developing. I also wrote a comment on that clip, but I don't know if you can still see it, I don't know how UA-cam works on this side. Please, if you can help me, I'm buying a PI3 or PI4, it's not a problem, but let's go. Thank you and excuse me for being bold. A beautiful day.

Hello, I have a problem. I have a pi5 and I understood from the forum that wiringpi does not work on it. I'm buying another board, I don't mind, tell me which model to get and if you can give me links to what you have installed. I would do exactly with the options you have in the video. I have to do a project with raspberry and I can't. Thank you

Link download please sir 😢

Link download sir

where can i get some of the buttons to buy

When I run this program I am getting errors is it because it's not connected to rung on left side or could be anything else

Thanks Engineer

Engineer you are doing very well

Following

Following very hard

Salut.Iti multumesc pentru videoclipurile pe care le faci si iti pot spune ca am invatat multe de pe canalul tau. Te as ruga daca poti si ai posibilitatea sa faci un clip cu controlul unui motor trifazic cu Vfd control in Open Plc. Multumesc si spor in tot ce faci.

what if i dont have serial com in my PC

What kind of transfer paper did you use?

Good content, and keep going!

I followed every single step you did but I didn't get the runtime to work, can you please help me troubleshoot what the issue might be. I think there is something wrong in between the KEPWARE server and the Wonderware. I checked the Access name setting like application name and topic name everything is fine, it's really confusing!

I did update, but programme not open at all?!

How fast is modbus

Very good, thanks!

what is input range of arduino PLC? means can i connect directly 12 volt sensor to it?

In some rewinder application plc program , a FB is made with name of Diameter Calculation in SCL language, can you please tell me from where I download that to insert in my program. Is that is Siemens function ? Plz suggest

Can you give me the code?

great video and review, succinct and yet very informative. thank you

Amazing!

Thank you so much for the nice review! 🙂I am glad you enjoy it! Would love to see some new projects made with it 🙂Keep up the good work! I love your projects!

Thank you

Thank you, very informative video about OpenPLC.

Thanks for the uploads.

Got past the "Install OpenPLC" on the Pi. Did the check to see if it was running. it was not. failed (Result: exit code) Start request repeated too quickly tried to manually run OpenPLC_v3/start_openplc.sh as sudo. Got error: File "webserver.py" lin 6, in <module> import serial.tools.list_ports Tried to Upgrade to Python 3 (seems to have failed still at 2.7.16) Commented out: import serial.tools.list_ports (just to see if it would finish). Got next error: File "webserver.py" ... No module named 'pymodbus' Tried installing pymodbus and anything associated via pip Still does not work. Advice?