Відео

Thx

Thank you for this great video

You didn’t count the number of turns when you put tension on the springs using both winding rods and counting number of 1/4 turns.

Great video despite others objections.

Thank you so much for making this video . I really appreciate your time and effort. Additionally well done ! Great video

Thank you sooo much for your detailed cable replacement, you are the only page I could find that would replace the cable when the door is down, there's no way I could lift my door up and replace it the way every other channel shows.. thx !!

get a better step ladder safety first

What if it's stuck down from the outside? It's off track one cable came off. Can you on the side cut engaged cable to release the door to even out. Can't do it from inside have no access from home. It's a condominium garage. It's manual with a key not a motor. Can I enter along side slit and cut the cable that's attached to open the door to repair. Than you! Also how much will this cost estimate me if I can't do it myself? 😢 I can see that one cable is not on. Can I cut the other to even and open??? 🙏🏾

I just had my garage door adjusted. It seemed that the technician was very aggressive in tightening the springs - 36 quarter turns. So tight that the new position was 3" shorter than the previous setting. He also tightened the bolts that attach the spring to the rod well beyond what seemed necessary ( I viewed a video that said to not overtighten them as it distorts the rod.)

Thank you for your advice! I gave it two shots and had surrender... still had to call a pro... nonetheless good video, I hope others can fix theirs using your instructions!

So that’s why my garage door is bent right there, whoever did it previously must have never bent it back lol

So the tension part should be in the middle of the door? My cable busted on one side and the tension part is all the way to one side.

Thank you no. 11 door arm ( quick disconnect in your video). Experiencing extreme frustration looking through door parts websites didn’t know the name of the door. Thanks again.

The photo eyes are installed to high off the Floor need to be 4” to 6” off the floor for Safety Reasons

thank Very helpfull The best expanation I coud find.

What an amazing video!!!!! its hard to find a contractor that knows about garage doors and will actually come out. This is crazy helpful. Thank you so much!!!!

I had this similar issue and got it fixed. Great instructional video. Saved me a couple hundred dollars!!

This was an excellent informative video. Thank you

What is the piece the lifting arm bracket screws to called?

I just fixed mine! thank you very much!

Thank you sir I been trying to figure this out for a while

I've seen some other videos but this video truly guides you along answering the question: WHY for everything. Great video.

Thank you! I appreciate the help. Great video! Very informative...

could show the IPPT calculation....then ,max turns

Too bad the manufacturer doesn't give specific torque specs on drum and spring set screws...fewer over or under torques...but then meh must not be that hard to get right without a torque wrench

Unwinding the broken (second) spring? For lube and tune, what do you to lube?

Why would you ever put a shorter spring if it doesn't last as long? Why not put the longer spring that lifts the same weight? Cost difference?

Love it!!

Great tutorial video.Thanks and this will help me a lot as a first timer.

I have a new garage door that makes one loud popping noise going up and down. It pops when a certain section bends. Any suggestions?

Porn🎉❤ 1:01 1:01 1:01

Excellent video! The quick release arm screws came off. I didn't know the name of this part, so your video helped out😊 Thanks!

Amazingly explained. Thank you so much.

This was explained so well! Thank you. I feel like a pro now. I guess I’ll go try it out.

By far one of the best explanations of a diy I have ever came across.

You have very informative videos.Thanks.

In my profession, when on a call for a "service/repair". It's policy to replace the cables, do not install the kinked & frayed cables back on. Otherwise another service call soon... Great info video😁

Gracias

Really good explanation thanks

Any update on him breaking his leg for standing on that little stepping stool like that? How’s he doing? Good I hope.

Hahaha he called a bottom bracket a drum

Cable clamp left side with a come along and lower door while some one kind of keeps the right side level if you don’t have some one use a second come along NEVER EVER EVER PUT A DOOR DOWN HOW THESE MORONS DID VERY DANGEROUS

nah...much easier method...no drum release required..raise the loose cable side higher than the tension side..rewind cable on drum..lower , then check balance..use a piece of cardboard not to damage the wall with vise grip, too

Great but if there's only a single spring ???

This is exactly what i needed help with. Thank you both

Thank you so much. Very well explained. This video help me a lot.

Don't work on the drums in either position. You're going to get someone hurt bud, not all springs are 225s 🤏🏻

Great video!!

My right side cable keeps un-spooling from drum. I fixed once and it did it again today. Should I push garage all the way up evenly and then lossen both spools and then tighten them up? Or do I need to re-spool and then look at tightening my torsion spring? Can't figure out what's causing this cable to keep unspooling

Does not work and DANGEROUS! Only bends the garage door guiders and will cost you $3000 instead of $500