Відео

114" is correct, that's from the roof line to the top of your chimney measured from the roof on the high side of the chimney to the top. That will bring you two feet higher than the ridge of your roof.

Same thing, except a much more costly and difficult install

I would suggest a wood stove rated for mobile home that can take it's intake air from outside and they don't depressurize the house. They are not special just rated for tight fit homes, there are a lot of affordable ones on the market.

Yes , I did that. The problem with that it is illegal .the fresh air intake can become a chimney, 😮

Here it's not illegal to install your stove anyway you want, just not insurable. In this case it's recommended to use. The stove would have to be rated for and certified for this purpose being used in that manner and insurable and yes there has been anomalies where the flue gases reverse that's why they use non combustible venting for it. @@MrSprintcat

Thank you for your reply, Chris. I'm thinking that having a company come out and do weatherization on my house was a mistake. My old wood stove ran much better ,with not that much more wood . Now we are air tight with a high efficiency, BK, wood stove, and stainless steel liner the challenge is great😢. Old stove in 20 year old chimney was the cats meow 😅.

Through the roof is always the best option. Keeping in mind that the most important issues is placement of the appliance and having the most direct and shortest route to get flue gases out of the building envelope with the fewest amount of direction changes.

When in doubt bracket are less than 100.00, some lighter wood rated chimneys I would definitely use bracket like ICC EXEL chimney.

Go to www.chriswoodheatservices.com/links-blogs/ there you'll see a link to GUIDE TO RESIDENTIAL WOOD HEATING from CMHC

Flat roofs pose a potential problem with leakage, having said that yes you can, as long as you out of the roof minimum 3' and are higher than 2' of anything within 10'. This applies if you live in Canada.

1890 Beckwith is a parlor stove, but if you live in Canada you'll need to install it with the firebox 18" off the floor if installing it in a garage, just like other fuels (there is exceptions) sealed units etc..

You can add the chimney cap for additional height, but according to local codes and manufacturing instructions that I deal with you would need 24" above the ridge, you could have issues with turbulence or down drafts and even insurance issues unless you comply

@@chrismajor6682 gotcha , thx for the quick response! You Rock.

Keeping in mind that your local regulation need to be considered but the installations instructions of factory chimneys and the standards here in Ontario Canada would be a minimum out of your roof 3' and 2' higher than the highest obstacle therefore is your chimney comes out of your roof 3' and there is nothing around or within 10' other than your peak or ridge of the roof you would only need to be 2' higher than that (the peak). Check you local officials to get your local codes etc... Having your chimney unnecessarily much higher there is possible issues with the flue gases cooling off create issue in very cold climates.

@@chrismajor6682 we put the chimney 4'6" higher then the peak of the roof top

@@claytonroberts344 If I am understanding you right, that's higher than the codes and manufacturers instructions I deal with. The issue is then if it gets cold enough where you live the flue gases can cool off too fast and turn to a solid, (more creosote) if not, you would have better draw going higher.

@@chrismajor6682 that's what I was thinking too.

I was thinking on going 9 to 10 higher up to get it were it is the same high as the peak of the roof of the neighbor's house

B vent is a vent not a chimney.

@@chrismajor6682 yeah i know thats why they call it a vent LOL. I was referring to if you just want to use a b-vent thru the roof. I believe there is a 8' rule

@@bkoz319 I'm a gas technician as well and It all depends on the classification of the appliance that's being vented and the brand of certified materials used It's easy to generalize in general conversation but it's technical with all the different types of appliances and circumstances in roof configurations. Gas unlike wood is not a DYI project.

It would depend on the one inspecting the unit, I would think without seeing it one on the corner would be enough, think of a car, lawn tractor or other toys as 4x4 or snowmobile etc would hit it before hitting the stove. I don't think it's logical to think you can stop a out of control vehicle from hitting the appliance or going through the wall for that matter. But protection from someone encroaching to close and a notice by an impact to the driver/operator.

Just the shampoo not the conditioner LOL

The chimney manufacturers all have roof flashing that is certified for their chimney system, the best way is through the roof, I use a metal flashing on metal or asphalt shingle roofs. Check with the brand of chimney you are installing as to what is available.

@@chrismajor6682 okay thank you i will do just that.

Not really getting the question, check out an installation manual to get the basic requirements for what your doing.

@@chrismajor6682 thanks for your answer sir i downloaded your manual but i cant understand. I have a 7x6 metter home with triangle roof with tiles height 4 metters. If i have a total height for pipes 3.8 metter that means i come + 50 cm up the top of roof how many metter is the max horizontal length of pipe i can have? Pipe size is 120 mm (5 inch). Hope you can understand me

@@user-bn8qr2gz8l It sounds like you need to get a professional to assess your situation, I cannot determine your needs in what your telling me. Good Luck

Yes and a minimum of 3' above the roof line, it gets tricky when the roof is steep and the roof itself is withing 10', that's when the formula helps. thanks Casper for your comment.

Yes of course, but factory chimney's are designed for the general public to install as a DYI projects, and is why they are sold in hardware stores. Not all people who install their own chimneys do it for fun but out of necessity, installation by professional can double or triple the cost of installing a factory chimney. Not sure about your comment "it may cost a bit" you can add 1 to 2K. I install and/or consult, then inspect either way it gets done right.

It's not rocket science so getting it done right is pretty easy to do. It's not worth doubling or tripling the cost when you can do a couple hours research and find out the info.

@@NickFrom1228 No it's not rocket science, I picked the two most common issues I see where people tend to get it wrong, chimney height above the roof line and Garage installs requirements. Thanks Nick.

@Nick Knight So true I saved 2k by doing it with a friend, researched all the codes and is all done in code, and the satisfaction of doing it yourself was priceless!