- 9
- 10 142
ptandjb
Приєднався 7 лют 2007
Eddie's Electric Car Project Finished After 37 Years
Decades of off and on work went into this electric car project that was finally finished in 2019. I was involved only in the last two years of the process and Eddie, Norman and I worked to complete the project. I did mostly electrical work, Norman and Eddie did the bulk of everything. I had promised to do a video but only learned sufficient skills to get this admittedly low tech video done recently, two and a half years late.
Переглядів: 73
Відео
How To Cut Squid (Preferably Frozen) for Porgy/Scup Bait and Use On The Water (Porgy Video 3 of 3)
Переглядів 1,1 тис.2 роки тому
This Video discusses how to process frozen squid to make prepared cut baits for porgy fishing in advance and store frozen for later use. Also baiting of the 3 hook rig of the first video of this 3 part series is discussed.
Recommended Porgy/Scup Spinning Rod/Boat Gear and General Fishing Tips (Porgy Video 2 of 3)
Переглядів 1,6 тис.2 роки тому
Recommended gear and general fishing tips for new/beginning porgy fishermen. These recommendations are based on trial and error over my first two seasons catching porgies in Connecticut near shoreline Long Island Sound waters at my recommended depths of 25-50 feet. Fishing experience developed on low wave forecast days in a Starcraft 14'3" FS14 boat. This video is intended to make it easy for b...
Tie Your Own 3 Hook (Hi-Med-Lo) Porgy Scup Bottom Rig (Porgy Video 1 of 3)
Переглядів 2 тис.2 роки тому
After two seasons experimenting and going through many design iterations came up with my current 3 hook bottom rig design and assembly process anyone can easily do. This video explains step-by-step how to tie this very effective bottom rig for porgies/scup. These instructions can be modified to adjust the design per your own personal preferences or make other types of bottom rigs. Please put co...
2021 Tohatsu 9.9 HP MFS9.9EEFTL Electric Start/Tilt Outboard Motor First Pics
Переглядів 2,5 тис.3 роки тому
Received this new Tohatsu from Online Outboards. Just learning to do videos, this picture sequence done in Shotcut. Actual videos will follow.
Pileated Woodpecker Courtship? #2 of 2-Raw Unedited
Переглядів 518 років тому
Pileated Woodpecker Courtship? #2 of 2-Raw Unedited
Pileated Woodpecker Courtship? #1 of 2 Raw Unedited
Переглядів 2138 років тому
Pileated Woodpecker Courtship? #1 of 2 Raw Unedited
Suzuki 2.5 motor mount test on Seahawk II
Переглядів 2,6 тис.9 років тому
Replaced standard Intex transom with plywood version to raise motor 4" higher above water and to get swing clearance for tiller
Get on with the cutting save me the details
Any issues with electric start?
Thanks, I’m 17 and this is my first time fishing for porgy
Bro is exactly like me I’m 17 in Long Island trying to catch porgy
I was gonna try using a coping saw to saw up the block.
The prices on these reels vary over time on AliExpress, sometimes free shipping, sometimes not. Wait for free shipping. Average shipping time to date 8 days. Also these inexpensive reels will rust easily so do not get water salt or fresh inside the reel. Also after salt water use wipe down reel, remove spool and clean where accessible and lubricate reel. Do not rinse with hose, water may get inside.
Link for hooks? Thanks.
Sources come and go, one current link: www.ebay.com/itm/322494201256?var=511469780327
@@ptandjb Thank you
thanks for showing your video. you made it look easy
last night I caught 2 porgies with this rig
Super dobar motor sa dugom osovinom sa malom potrošnjom na pola gasa za mene bolji od yamahe ja sam tohatsu 5 hp ima 21 godinu i nikad problema samo ovaj noviji 9.9 duge osovine nema još kupit u hrvatsku
Super je. Svidja mi se sto nema carburetor. Evo baš gledam reviews i planiram da ga kupim ovu sedmicu :)
Please guys...is this short of long shaft this motor you have . Thank you . Cheers
this is a short 15" shaft, to my knowledge this small motor is only offered as short shaft.
Thank you so much . Very kind. Any thoughts about this Suzy 2.5 please. Went to see a used one 2007...look good but I am new on boating. Do you recommend this motor compared to a Honda 2hp. Thank you in advance. Best Regards
cruise the web, main differences Suzuki water cooled and reasonably quiet; Honda air cooled and sounds like a lawnmower, which is also air-cooled; most commenters seem to prefer Suzuki, that was my choice when buying new.
Yeah I been reading around....but wanted the word of someone who have it. I am going to buy it . Thanks .
I have the same exact boat and outboard motor configuration as you have here. Does your motor like to bury itself when you get on the throttle, like mine does? I'm trying to get any ideas from others on how to keep this from happening.
+Kevin Knudsen Yes, the motor tries to bend the end of the Intex Seahawk II (aka Mariner 3) boat down from the torque produced by propeller thrust, bringing the 29 pound Suzuki 2.5 HP engine too close to the water. It was really bad when I first launched here at Mashapaug Lake in Connecticut that day even with the new plywood motor mount. I returned to shore and added as much air as I was comfortable with to make the boat stiffer. That helped a lot. Also on my previous outing with the standard Intex motor mount I was concerned how close the motor got to the water surface. Disassembled motor mount, cut a piece of 3/4" plywood to raise motor 4" higher. This height still kept the water cooling intake port below water. This also brought the propeller closer to the surface making for less torque force bending the motor toward the water surface. Of course, the ultimate solution would be to attach the motor mount to a frame attached to a hard floorboard, but what I've done works OK for me.