![JoJoMasterson](/img/default-banner.jpg)
- 15
- 73 073
JoJoMasterson
Приєднався 6 кві 2021
ima shitpost here
A1/A2 Buttplate Repair
Had this video done for a while just had to edit it, and I'm Lazy
Переглядів: 383
Відео
DD RIS II FSB Hao To Install
Переглядів 28 тис.Рік тому
how to put on your dd RIS II wit da front sight block
Hao To Replace Your Berretta M1951 Locking Block
Переглядів 11 тис.Рік тому
Vid I made on replacing your m1951 locking block with a new one
Replacing AR Dust Cover
Переглядів 2,2 тис.Рік тому
Video on how you can replace your ejection port cover/dust cover on AR style guns.
Garbage Guide: AR Upper Parts Kit Install + Super Easy C-Clip Install
Переглядів 161Рік тому
Video I made on installing your upper parts kit, and a super easy way I found to install your dust cover c-clip without it flying across the room, forcing you to buy another one, which will cause you to wait a few days. In those few days you will be wondering, why didn't I watch this video, why did I fail to consume this brilliant (wildly autistic) content, and where was this video when my life...
DIY IDEX Ender 3
Переглядів 3,1 тис.2 роки тому
Built this a while ago and found the clip. NGL prob wasn't worth the effort.
Garbage Guide: Side Sling Swivel Install
Переглядів 6 тис.2 роки тому
Quick video on how I set up my side sling swivel. Stuff I used: Electrical tape 1 3/4" Knipex Pliers Wrench (Channel-Locks will work too, but make sure to use a generous amount of electrical tape on the jaws to prevent scratching) Shims made from a drink/soda can Large Shim = 17mm x 34.5mm Small Shim = 17mm x 14.5mm These dimensions are loose, you may need to change the size for different manuf...
Garbage Guide: DIY Rust Blue
Переглядів 16 тис.2 роки тому
In this video I show you how to rust blue my way. Supplies: Rust promoting solution (off the shelf solutions will work too, but this is non-toxic and cheap) -Hydrogen Peroxide (3%) -Sodium Chloride (NaCl) Denim Rags Heat Gun Heaters Steam Pans Old Toothbrush Wash Bottles Being Based Purified/DI water Check out my Odysee for files and content that isn't up on my youtube: odysee.com/@JoJoMasterso...
Garbage Guide: Repairing A Pattern 83 Battle Jacket
Переглядів 1,9 тис.2 роки тому
In this video I repair a pattern 83 battle jacket using a sewing awl. What I do in this video can also apply to repairing other pieces of outdoor/tactical gear. I'm no seamstress so please go easy on me. Materials used -speedy stitcher (sewing awl) w/ #4 needle -Bonded Nylon 6,6 thread #138 T135 420D/3 -3/4in A-A-55301 Milspec nylon webbing (I sourced this from jontay) Check out my Odysee for f...
3d Printed Vityaz/KP9/KR9 Mags Test
Переглядів 5693 роки тому
Video of my friend firing the 30rnd Mag. How to make the springs: ua-cam.com/video/mIuBKca4FrU/v-deo.html Magazine Files: odysee.com/@JoJoMasterson:6/3D_printable_vityaz_mags:2 Check out my Odysee for files and content that isn't up on my youtube: odysee.com/@JoJoMasterson:65b9831d92836908e1593f0b8b7f7bf54ada17f7
Lunk Alarm
Переглядів 3573 роки тому
Shitpost I made just for fun. Idk who the original comic is from.
Vityaz Magazine Spring Winding Video Guide
Переглядів 8313 роки тому
I hope this video helps anyone trying to make these magazines. This is my first attempt at making a video, hopefully it isn't that bad. Magazine Files: odysee.com/@JoJoMasterson:6/3D_printable_vityaz_mags:2
Just installed mine (Colt cage code) and didn't even need shims. Thanks for the info. 🤘🏿🤘🏿
Nice, thanks.
Based GFL m4 wife thumbnail
Thanks for the install vid; the info/tip about the shims was spot-on, and made my install solid (Rock River version). TY
MEILING MENTIONED OORAH
I like the $Boys beats in the background!
The DD SOCOM profile barrel is only* available when you buy one of the Brownell's special uppers with the brown rail.
You should not ever use loctite when threading steel screws into aluminum.
Good vedio nice Info,, but plz never put cartoons in guns vedio my eyes are hurting
7 mermi sıkıp kırılıyor bendeki. Toplam 3 adet kırdım 1 hafta içinde ne yapmam gerekiyor lütfen yardım edin
great vid! what size of knipex pliers do you have? Would a smaller knipex still do the job?
I have the 10" ones in the video the other ones might be a little limited on the jaw opening size to get around the pins.
That is not a SOCOM barrel, that’s a government profile barrel. You can tell by how skinny it is behind the FSP.
Well explained and very good job! Thank you very much!
Nice 👌
500 for a rail. Id rather buy ammo
Interesting to see your methods of putting this rail on
29:00 "this guy is very quiet ill turn up the volume, couldnt hurt" 29:55 "fuck me"
What kind of adjustable wrenches are you using? I like them.
It's a Knipex Pliers Wrench, IIRC the one I use in this video is the 10" version.
I’ve got an upper with the serial number in the 12000 range and a lower in the 18000 range. The slide uses original style parts and I think the frame does as well but when it comes to getting them to sync up I just can’t rack it all the way back. If you have any tips it would be appreciated.
I have one that’s stuck I can’t take it a part, the empty ammo inside it do you know how to fix it?
Couldn’t stay awake…💤💤
What height dot needed to get that front iron at lower 3rd? Looks tall
Is there a plastic lining within soda and beer cans? If so, has it melted to your barrel?
Can you please tell me......do you know what you are doing ...........????
I have doubts.
You just use a standard barrel nut?
If you have a DD RIS II it should come with its own proprietary barrel nut and wrench.
Do you use a carbine length gas tube and barrel ?
Yes the barrel and gas system are both carbine length。
Freaking Love the berserk references. And. The soundtrack
Idk ive always thought those rails were cool when i first got into guns and now i remind myself how fundamentally goofy they are, but i dont doubt it works for you good video
Ditto
I am a sucker for quads and fixed front sights
Did that rail come with the hardware to mount the m203?
Bro, my piece will absolutely not go onto the barrel (into place in the slot of the iron sight). It's too tight. The website I got it from swear that's it's a US GI piece, and it looks identical to yours.. I'm trying to put it on a Colt CR6920, Aland it is just too tight. 😭 Any tips?
Same here. Mines a RRA part.
You have to tap out the tapered roll pins to the FSB and it will then give you room for the swivel.
Guns and anime. Home.
Looks freaking sweet bro!
Will a 16 inch Fn barrel work
It should work if you use a barrel with a carbine length gas system, if you use a different length gas system you might run into issues with there not being enough clearance for the gas block.
Thanks 👍🏻
What pliers are you using? Also what rail length did you use?
"Hao To Install" haha
Thx good vid
Too much work,I'm just gonna buy one from broenells😊
Will a emg daniel defence licensed 9'5 m4a1 handguard fit a LM4D
Where are you purchasing your lowers?
Did you use a torque wrench/screwdriver on the handguard flange screws? I cannot find one that will fit and wondering if it's absolutely necessary. I didn't know if you could just hand tighten then give it a 1/4 - 1/2 a turn more.
I just hand tightened it then gave it like a 1/4 turn. If you want to use a torque wrench to ensure everything is to spec, you could use a ball hex on the end of your torque screwdriver/wrench, just keep in mind those will strip out before a regular hex would so be careful.
got that thumbnail game down
Bro help will this rail fit the Cilt OEM 2 or is the gas block too big
Negligent discharges are a normal part of firearm ownership
Heavy boom boom 😢
I picked up a Socom profile from Faxon
S&W M&P15 16 inch 🤔 will it fit..
I wonder what caused that crack 🤔
age