Відео

dios tevediga entodo el travajo

What fog lights did you use to fit ?

This stuff is not garbage. If you cleaned both surfaces properly they would not come apart unless you tore them apart.

Well this didnt work i replced fues on fuse boc replace rack replaced woring and also checknunder dash meter 7.5 fuse and nothing 🥲 also replaced the module box and still nothing 🥲🥲 any help in this

it worked ! thx !!!

I got those Hardrace tie rod ends but the taper is not right and the fitment is off, I don't know why

You get the issue resolved?? Concern on vehicle fixed?

💪🏻💪🏻

My EP2 is having EPS problems for 1 year. It started to turn the EPS light once in a month, and now it fails every 10 seconds or so... With a fancy scan tool it showed "motor voltage error", the battery voltage never went below 12.7v consuming 59A...I will try this and update the progress...

It worked thanks dude. I was tripping out why the eps light was on i thought it was some electrical isssue since i have my battery light on and thought that was casuing the eps light

Gracias por el video me ayudo bastante "thanks"

Big help, thank you very much. I confirm it's the same for ep1 and ep2, you don't have to splice the wire. Just use a hard copper wire and push it in the hole of pin 8 from behind.

Ok so you turn 45 degrees the. Turn the ignition on ok ok

So when they say tur. 45 degree how do they mean and mine stays flashing

You sir, are a life saver! Been tearing my hair out trying to sort this light issue.

bro can you get me the connector for the windshield washer pump and the connectors for the fog lights?

can i replace the knock sensor if i take out the alternator?

Thank you so much. This was extremely helpful. I was ready to remove the rack and replace it with a new one for $700

gigo

U dont need to do anything like that. U turn your steering wheel 45 angle then turn on the ignition to reset

Idiot doesn’t use 99% alch to clean surface complains about tape not working

Thanks for the video! The a/c in my ep just doesn’t get very cold anymore even after being topped off with a/c freon. Looking at just replacing the whole system since I don’t know what the problem is. Your video is some good info for part of my project soon thanks!

I think the issue could be the plastic mount on that skirt is not designed great. One area to hold all that skirt is too much. No wonder it doesn't hold. For the tape to work it needs like 2.5cm length for every half a kilo - assuming everything else is followed like clean surface free of oil etc.

That spring is connected to the “P” lever mechanism only, there is no spring to return the foot lever in that area,

That's all the parts my ep3 needs. I'm also looking to get a LSD for my trans too. Right now I have a 05 TSX K24A2 swap with a RSX Type S trans. I also swapped in a Type R Oil Pump, valve springs, and Type R PRC intake manifold. Still needs to get tuned.

I like the Type R bumper too. They look clean with the preface headlights. I actually like the preface headlights better than the facelift to be honest. Nice carbon fiber piece you have too.

I love to get me a set. Right now I only have the usdm side skirts.

Nice to know. I'll revert back to your video whenever this happens to my ep3.

I ordered this same bumper. Did you have an issue fitting the bumper over the stock metal bumper support?

Did you prep the mounting surface on the side skirt? I used this stuff to mount the front lip on my car and I skidded into deep snow and the front lip didn't budge.

You bought the wrong one, thats the light foam tape, same thing happen to me and i had to return it..

does the same grill fit on this bumper ?

Your garbage Honda couldn’t hold the sideskirts on and you’re gonna blame the tape you used wrong

User error is garbage 🗑

I love how that facelift bumper looks. Way better than the USDM one.

3 years late but I'm here big thankyou x

Can you clean it and maybe sand paper it for texture. And give us an update please

Yooo what did you use for brackets couldnt understand you

We’re u bought the part from

Plus it needs 24 hour cure time before you attach both sides together

Hey bro, I have a 2003 ep3 how much did you get your TR side shirts for and where?

Pretty sure your surface needs to be clean, and also have more than one adhesion point. If all of them are "garbage" it's user error.

Sir, would you please contact us through info@llptapes.com? We would love to find a solution for the issue you have and we are always here to support. Your satisfaction is very important to us.

If you got the rear bumper, what size is bolt on the inside of the crash bar??

Bruhhhhh u did all that work for just the knock sensor?! You didn’t need to do all that

You need to work on your presentation. Boring, dizzy, and no connection with the viewer.

Great vid! Gave you a thumbs up! Hope you had good luck with the sale. Hope you can drop by my channel, where I teach acoustic guitar lessons. Have a great one! :)