Відео

Go buy another throw that in the box there's your new tool Go return the old trash

Yeah man, bought one for an industrial pump job to get in some crevices. Loaded with m12 5.0 high output bat and had the same issue of it randomly slowing down when not under load. Sometimes not even firing up when the triggers pulled. Milwaukees pretty solid on their warranty repairs so I’d recommend sending it in for service

Problem is you should of got a DeWalt

Hahaha, i learned i hated mud as a kid growing up on our farm.

Speed setting three doesn’t do that

Speed setting three doesn’t do that

I have the same tool. I only run a 4.0 battery or higher and never ever had problem on over year and a half. 3.0 is not letting it run at full speed or power !!

Looks like a lemon, it’s bound to happen at some point, have it warrantied, Milwaukee covers the whole process

Mine does it too. I take battery off and on. It works but sometimes it just stops

Wrong application. Save that cute lil fisher price tool for something small.

Went to change a pony motor on an old D8h at the landfill during the winter. The operator had taken lots of dumps down the side of the motor. We told the city on the way out we'd come back and do the job after they steam cleaned the dozer.

The issue is that Milwaukee is owned by the C C P

My Milwaukee drill does the same thing and I just bought it

220 for bare tool shts like 160 amazon

I’m a Milwaukee repair tech it’s the defective electronic module. Extremely common in all Milwaukee brushless products. Look up your local shop

Only thing i can think (other than the tool being defective) is maybe it's too much load for the 3ah battery to take. Try a higher capacity battery pack or maybe a high output. If it's the same then warranty it out. Defects happens and sometimes you're just lucky enough to get one.

Could be a battery issue. Could be a tool issue. Unless you’re pressing down really hard.

Wow somebody that is not intimidated nor afraid to work.

Same with mine. It kicks into protection mode. Anyone that says they don’t have that problem doesn’t use theirs enough. Doesn’t matter what battery you have on it. Cut off wheel is a dud as well. Only complaints I have are these 2 tools in the m12 lineup.

Get a good set of rain gear, the heavy stuff. I used to wear mine dealing with pipe in mud that would pull your boots off. Worked great

I have for the same thing in feild service! Makes the tarp like a water bed 😁😁😁

Hello its hot ovrheat..🔥

That dozer is begging for steel plates all over it!

Makita is better

I have the angled and the straight for years, it's been a game changer for me... Although the smallest large packs I own are 4.0s, I try to run mostly 6.0s in them or even better the couple of 5.0 HO-XCs I own... Unless Milwaukee changed the overload because of too many burnt up units I'd say you may have a lemon... They do perform better with minimal rotating mass, so I usually run a lightweight 2" backer even if I'm using 3" rolock pads... That looks like a pretty unnecessarily heavy 3" backer, which may be the issue if they have upped the cutout when using lower capacity batteries 🤔 Remember brushless motors want to stop when they are getting slow or lose power, but sometimes on pneumatics the heavier backers can help prevent stalling once up to speed... If you get another one or try this one more try a lighter rubber or composite combo backer instead of the big hunk o' rubber 😉👍Hope it works out for you, I love both of mine, and my straight grinder lives with some shape of carbide cutter on it full time, for steel 90% of the time! 🤷‍♂️

you bought milwaukee what do you expect

Does it do that when it isn't under any load? Can you just hold it and run it and it shuts off?

Milwaukee is garbage

Try a different battery I've had a lot of batteries do goofy shit

Return it bud. Why even make a video 😂?!?! They’ll swap it for a new one and you’ll see it’s just THAT one.

Sounds like you need to find a pressure washer!

Its a Milwaukee thing! Have many Milwaukee tools that do this crap.. hammer drill..impact gun..throw away tools😊

Good luck

Is this Cat years or Dog years?😂

Used to enjoy the same thing helping my daddy and he taught me a lot by the time I was 18 so I wanted to go to school to learn more. He talked me outta it. Idk what he said but whatever he says I usually do it and I'm 35 now and still enjoy working on his stuff with him but after that idgaf about it. And we work in a nice fairly clean garage usually and have the tools we need. I hate having to work on shit on a job in the heat, wet, cold, snowy shit. Winter we do a lot of major things going through his equipment so usually field mechanics is usually minor shit.

Dozers suck complete ass to work on

No issues with mine, warranty process is easy, send it to Milwaukee.

Battery can't handle the current. Usually flashes the lights

Hot chocolate is my sweet spot

Thats a first world problem bro... now cold hot chocolate really bends my blade

Yup same here with wire brush but I noticed load and triger pressure sets it off

now fixing equipment is a chess game because of this one miserable fk

bro why would someone even consider nuts and bolts under what a simple fix was what a prik

A liberal dressed as a mechanic

I didn't like the color of the mud. Deal breaker! Call local towing company with a rotator wrecker. Relocate the piece and work in a dryer location for major repairs.😊

Wow that's crazy I can't believe they wouldn't scrape all that crap out of there and maintain it😂😂😂

Yep I know the feeling I did flooring for about 30 years under houses and doing anything you can think of plumbing remodeling etc😂😂😂 be careful what you ask for you just might get it❤

If that was my machine you are working on, id make sure that you were in a lot better conditions. Mistakes happen when you're cold and wet.

bought it for even a simple task of buffing the inside of a tire for a patch even the slightest pressure they shut off

Suck it up buttercup if you don’t want to mechanic pay the ones who do I love to take your cry money