- 609
- 1 476 474
automotive tech-vet
United States
Приєднався 2 чер 2015
Automotive repair and diagnostics and advice
Відео
gm code PO496 evap system flow during non-purge tech tip of the day diagnosis and repair solution
Переглядів 2610 днів тому
hard brake pedals Chevy equinox and all engines with a vacuum pump for the brakes tip of the day
Переглядів 3,8 тис.10 днів тому
tech tip of the day how to put you infinity into neutral electronic shift
Переглядів 360Місяць тому
toyota siscion xb 2011 maintenance reminder reset procedure
Переглядів 327 місяців тому
flat tire tech tip of the day
Переглядів 757 місяців тому
how to manually put flip up head lights up and down tech tip of the week
Переглядів 782Рік тому
how to change cabin air filter toyota 4runner
Переглядів 62Рік тому
Created by InShot:inshotapp.page.link/YTShare
how to reset oil life message chevy Colorado
Переглядів 3,5 тис.Рік тому
how to reset oil life message chysler town and country 21
Переглядів 205Рік тому
tech wiper diagnosis tip
Переглядів 195Рік тому
tech tip of the day axle install tip
Переглядів 135Рік тому
how to reset maintenance reminder toyota highlander
Переглядів 354Рік тому
how to reset maintenance reminder toyota rav 4
Переглядів 348Рік тому
how to reset maintenance reminder mazda cx3
Переглядів 1,8 тис.Рік тому
What about 1.4 whiteout turbo ?
do you ever review your videos? my guess is NO! your video was/is a complete waste of time.. could not see what you were doing and the audio sucked!
Yup perfect fix much appreciated 🙏
Thank you 👍
So, is the pad sensor built into the e brake?
@@PushrodBob no it's a sensor you have to pop into the other pad on the other side
Thanks for the video. Very helpful for a home mechanic to see…1. How straight forward the job is 2. That replacing the whole control arm, with attached bushings is the cost effective route. 👍🇺🇸
Fantastic!!!!
Oof had one on a Malibu go out but it went out with a bang like by destroying the camshaft in the process. You got lucky
Needs extensive editing. Camera is bouncing all over the place.
How much would this job cost
Thank you, it was too easy!!
Hey, man, get that stupid text off the picture!! Bad move!
is this similar in location for a 2019 ford ranger?
I call bs. Had to work them 2 inner bolts out. Now axle wont budge from that inner housing
@@jimweimer6725 sorry you’re having issues it happens sometimes
Did you have to compress piston before putting caliper back on ? Did you remove cap on top of master cylinder so piston wouldn't push out?
What's crazy is not using any Spark Plug Boot Protector Dielectric Grease.....
Thanks replaced gasket myself 💙💙🥰 saved me 218$$$!!
fucking mint baby great video. very clean and efficient work!!! thanks you
that's what she said ,............................==========
took the wheel off to drain lmao
Not gonna take issue with your torque specs, only with torquing the forward bushing bolt before the wheel was back at ride height. Without that, you're driving around with a prematurely twisted bushing, right?
What are you supposed to do with the old control arms? Do any shops take discards?
Captions right over the spot we need to see. Genius. Lol
Cool ❤
Whats this seal really called
Horrible videographer
Is it the same for a 2011 ford fusion se?
Yes 👍
How long does it take to fix it. $100 an hour is crazy...lol
What the hell did you show. Be more specific.
how to delete the worn pads warning?
Hey man! Do you a tool that can fit on the passemger blend door?? Nothing fits the gap
thank you!
Not a complete proper brake job
Can you splice in the dorman quick connect purge valve that is designed for the 2.0 litre onto the 1.5 liter harness? I dont see why not, other than the electrical connector being at a different angle, but i could extend the wiring so it fits. What do you think?
Yeah that'll work
Thanks for the response, Ford in Canada wants $394.86 for the oem hoses before tax! $442.24 after tax. You killed it in this video getting all the ends off in less than 10 minutes by the way.
What makes you think we want to watch you fumble around while you piss and moan. Why can't any of you make a quick and easy video with a touch of editing. Nobody needs to watch you bust bolts loose, nobody wants to.
FREAKIN NEW GUYS lmao jk bro... camera angle was definitely off but I seen enough to know what I needed to find out lol... thanks man... and work on the camera angle 😅
Use a light next time
This was a great video thank you, do you think I can do without a lift like the guy below mentions?
Good way to f up your brake line
Ok but only last 6 months in my car then I have to replace it again duralast brand.😅
Watched several videos on how to reset 2019 Colorado. Only yours helped and made it incredibly easy! Thank you
Do you have to clear the codes from the history to get the dash lights to go away ? I have replaced the wheel hub and it is no longer throwing codes , but they are still in the history . I have the Service Engine Soon light, the Anti-Lock light , and the TRAC OFF light "on" at all times , even though they use to GO away when , and especially when you ran the car through a car wash , they no longer stay off but are always on now. My codes that are in the history are C1216, C1221 , C1225 , and C1232 . But like I mentioned it is not throwing codes . It has to be a wiring issue somewhere . This is a 2002 Buick Century .
Love it!!!
I've been told if you bleed the front caliper you have to bleed every single wheel is that true ?do you have to bleed the whole system?
That's not true you only have to bleed the one that got air in it
@@automotivetech-vet thankyou bro. I did my calipers rotors and pads today. Got to bleeding the passenger front. Put the tire on and the first break push I think I blew the front brake line above the banjo. Then I did drivers side and the craziest thing happened. I didn't buy a caliper so I used the old one and when I got to the bracket with the slide pin bolts, the bottom hole had ZERO THREAD! I mean absolutely no thread for slider bolt. It looks like it rusted away? So now I need a break line and a caliper.
Wouldn’t lift a transit by the side panels like that. Gonna get crushed one day and cost you big 💰 💰
Poor quality
Couldn't see much of anything
Didn’t work for me why??
Might want to leave the cover off until you fire it up and check for leaks.
I've find this in my hummer h3. I replaced the thermostat. After driving for half an hour the temp Guage starts to go up