![Drew Jackson](/img/default-banner.jpg)
- 7
- 36 500
Drew Jackson
Приєднався 14 сер 2013
Welding/Fabrication instructionals videos, Racecars, Motorcycles.
2023 ktm 2 stroke is a ripper
2023 ktm 2 stroke is awesome. The fuel injection has been spot on.
Переглядів: 202
Відео
2023 ktm 250 sx
Переглядів 967Рік тому
2023 ktm 250 sx. Just getting back into riding. I took 10 years off from the sport. This is my 2nd ride back in 10 years off on the new ktm 2 stroke. I love the bike so far its been amazing.
Quick mountain trip yesterday for lunch.
Переглядів 292 роки тому
Quick mountain trip yesterday for lunch.
How to read spark plugs and Tuning with datalogger
Переглядів 2193 роки тому
How to read spark plugs and Tuning with datalogger
Bent Axle Tubes?! - How To Fix It.
Переглядів 23 тис.3 роки тому
How to fix bent rear axle tubes. Here I straighten my axle tubes in my built ford 8.8 with 9 inch ends. I use a oxy acetylene torch to heat the tubes and draw them back to being perfectly straight. Kicked Up Pumps by Audionautix is licensed under a Creative Commons Attribution 4.0 license. creativecommons.org/licenses/by/4.0/ Artist: audionautix.com/
8.8 Rear End Build - control arm and coilover relocation
Переглядів 12 тис.3 роки тому
I show how I built and braced my 8.8 rear end for my sn95 race car. I used the tin soldiers coilover and control arm relocation brackets and 9 inch ends. Here you will see me tig weld the brackets on.
like the clip hope you cap this diff to make it stronger if you dont the first hole you hit will probably bend it
Lol man this car has made a thousand passes by now making around 950 yo the tire of 2 kits
Caution,,, As u have already mentioned AT 3:15 you can see the puck is not a tight fit on shaft ## TIP 1 / the puck needs alot larger diameter where it meets axle flange 2 / A locking collar which clamps to alignment bar can also help align /square up axle tube puck
whats material of the rod? I have two 1" ,one is classic normal full iron rod but seemed to me bit bended ,so I bought really hard kind of piston rod (for custom shocks fabrication or hidraulic pistons) but its also bit bended..and measure with those inaccurate rods is just circa, not very reliable.. or ,do you think 1" rod is too thin,despite its full inside ?
Did you use the 309 rod to weld tubes to the housing? I ordered 309 to weld front brace kit on and dont want to spend the extra on nickle if the 309 will holt the tubes to center as well. Also what control arms did you use? Im hoping any spherical adjustable will work
What size of tube you use
Nice job
GOOD WORK 👍👍👍👍👍
Very good ji
Killer work my man 💪🏻😎
Wow! Riding amazing for taking such a long break. New bike looks like a riot🤩
Maybe I missed it, but were the LCA brackets and coilover brackets set to ZERO with the diff housing, or were they offset and if so, by how many degrees? Excellent job btw.
These was set at zero but some companies recommend setting at a certain amount of degrees back. It'll tell you with whatever one's you go with
@@drewjackson4056 Thank you Drew
Great video, excellent the way you set the camera up to show the gap close as you quenched the hot spot. Seeing is believing. Great work, thanks!
Thanks man!
great video... if you could get a mic on you that would be amazing . its a little hard to hear you speak. over all awesome video!
Beautiful Work D!
double tap backwards 10 seconds (if you're on your phone) from the 2:44 point in this video and you can actually see the tube move like an eighth of an inch from the heat! it's pretty cool! nice job! or do this click on 2:50 then 2:40. it's amazing how much it dropped!
Yeah it's pretty cool
DO you still have a link to that diagram? You did nice work and its definitely thought through
Super helpful! One concern: does heating and quenching harden the metal, therefore making it more brittle and prone to cracking? Is the area spread out enough that it doesn't really matter?
A tube isn't going to break like that. The center section is by far the weakest
Shouldn't the adjustment holes be in an arc (rather than in line) as the control arm end will move in an arc?
The trz kit is like this. Which I really prefer because ones like mine requires you to adjust lower control arm length to keep correct pinion angle
can you use map gas if you dont have tanks?
Doesn't get hot enough
We need more videos!!!
Badass!!!! Thanks for the video
She’s bad man
What type of round stock bar and what size bar did you end up using ?
just go to local metal supplier and say i need a piece of 1.5 or 2 inch round stock
Great watch! Thanks man.
I need to get my rear end built like this, nice work. Rip your buddy’s eyes toward the end of the video haha staring directly at the welds😂
hes a welder. he knows not to look directly at it.
Good video. For an accident damaged axle, how close should I get it in the press before I finish it off with heat? 1/4"-3/8"?
What that lower bar for
Reinforcement
awesome stuff. whats the song in this?
Tnx for the vid. That job is awaiting me aswell. Have a 04 TJ sahara. Fitted JKR axles to it. Had to fab all new brackets to fit the longarms and marry up the jk axles to the tj chassis. Subseqently the rear axle warped in a smiley arch. Current low tech measurents show 6mm. Or 1/4" Hope your system works
yeah man mines as straight as an arrow thanks for the love!
Hell of a job...Well done
Good job dude! Check out my build
Nice stuff. Always wondered how to straighten them up. Now I know. Great work.
turned out awesome !
thanks man!
Nice....keep them coming
Looking good bro 👍
Good job bro!
Awesome work man. Always such great quality stuff coming out of your shop.
thanks man!
@@drewjackson4056 what rod was you using on the brackets? 309ss like on the housing?
@@nickm9854 nickel
@@nickm9854 and 70s on bracketa