Відео

That would have been cool to have.

@@dillbob4603 i have one of those. I can look at it and tell you what color does what. Or i can draw up a diagram of the plug and show what goes where. Is there a good way to get that to you?

@dillbob4603 If yours doesn't have the plug, Black ground Red rotators Yellow take down Green rear flashers Blue left alley Brown right alley White's speaker If you still have the plug. You should have seven exposed terminals and one covered. Putting the covered one up and going right to left Covered ground 1st rotators 2nd rear flashers 3rd take downs starting below covered one right to left 4th left alley 5th right alley 5th &6th speaker Hope this helps Let me know if there is something else you're looking for.

@marcs3982 Thank you for your time serving your community. I was a volunteer for 12 years here in Florida. In my county, they didn't let us do roof lights. So i had a windshield light. Red that was for fire. But after a while, they band us from using those saying that it was a liability. Right now, the one bar left to get is a twinsonic.

@@loosenut1969 thank you

@@loosenut1969 thank you

@jab642000 thank you, i have a second channel where most of my Halloween stuff is. There is more on there if your looking for more ideas. Type in halloprops

@@jab642000 thank you

@jamiesnider9568 No, i had to replace the rotators in the front bar.

@@rarmst75 thank you

@aldenlarrick503 if i can find the drawing, yeah. If i cant find it i can draw up another one. Then just let me know how i can get it to you.

@@testos2701 all plastic.

@@bluedakota80 So I went ahead an installed the gauges, 2020 Mustang EB base, and the oil pressure don't work, bummer, but the cable was there, and thanks to you the install was a breeze. Wondering is a tune will activate it?

@testos2701 I've been told some could, but i haven't gotten a straight answer from anyone which one would.

@@bluedakota80 I think I got it figured out in my case anyways. The sending unit on the base EB which has a green connector with just one pin by the oil filter won't send the proper signal to the oil pressure gauge, it acts as an on/off switch, maybe with a mid point reading because the base cars don't have and actual gauge, is just an indicator, low, normal, high, those are the 3 readings you can get from that combination used on non PP ecoboost engines. The PP ecoboost engines come with a 3 conductor black connector by the oil filter, I got BAMA working on a possible solution if there is one, but unless the sending unit on my car's engine is not change to the 3 pin black connector I don't see how this could work. Hoping to find a hidden 3 pin connector wiring harness tucked away somewhere in the car's engine compartment! Maybe by installing a full digital gauge that has that low, normal, high scale, but not with the ones that comes with the PP ecoboost and most GTs and or others as well. Bottom line, check your sending unit by the oil filter if you got a base model, if is green you will know what to expect if is black you are in good shape! The gauges look nice though, just not the pressure one since is not moving! The 4 pin connector was in the back of the radio tucked back there, it was there, so my question is why put the 4 pin connector there if on a base model the sending unit will not work with the gauges the 4 pin connector is for!

@testos2701 Yeah, the ones with the gauge factory. Come with a three wire sending unit. I found a wiring diagram a while back, showing it. But you have to connect it to the ECM, and then the ECM has to be programmed to recognize it so the gauge will work. Since it all runs through the ECM. And i haven't found a shop willing to do that. With the liability of doing damage to the cars electronic. Figured one of these days ill find a shop to do it.

@tommytomtomt i didn't think about using transparent paint for that. Plus, with the filters, i can change it up.

@@LiLSeBSwagg im not a shop. Just a DIY-ER

@ ah ok. I bought a quad tip active exhaust taken off a mach1 and I currently have a single tip active exhaust from X Force. The X Force wiring is essentially what you show in this video so it should all work, but I dont trust myself cutting open the small black motors and doing the wiring. Any chance I could bring you the car and pay you to do that part?

@LiLSeBSwagg no im sorry. I only work on my own stuff.

@E85_STI did your car come factory with it? If so, you should have a warranty. Have the dealer look into it. If you are adding it. Im not sure how Ford changed the system with the new generation.

@Domsgenerallandscape the lenses are held on with two screws on each end. Take those out and slide the lenses outward from the center. Or if you mean the reflector, those have a nut on the underside. Undo the silver plate they are attached to, and you'll see the nuts. Will have to cut the wires to remove.

@ that’s what i thought I have the screws out but i couldn’t get it to slide the previous owner dropped it and cracked it and I didn’t wanna break it anymore than it is thank you

@Domsgenerallandscape if its being stubborn spray a little silicone spray or WD 40 along the bottom on the rubber gasket. And just slow wiggle it and pull slowly. Ive had some not want to move. And thats what i do.

@ thank you!!

Just the intro. Lights went off at the end of my driveway.

@marcs3982 they're old and noisy for sure.

@vrgs1385 i bought one of those variety packs from O'Reilly. Came with the stud and nuts for them. There were three different sizes. Now they weren't the same thread size, but the diameter of the stud was the same. So i had to use the nut that came with it. A little black paint, and you can't tell.

⁠​⁠@@bluedakota80 awesome there’s an O’Reillys right down the street. I don’t think I’ll have room to sneak a tool behind so hopefully it’s strong enough. If not, I’ll have to go the other route. I do painless repair or at least I’m a broker now, but I have all my old tools I might be able to sneak one in behind for leverage. I’ll post back tomorrow and let you know how it went. Thank you so much for the video again!

@vrgs1385 hope it works out and gets you all fixed up

By the way I am not placing a statue on top of my obelisks so it won’t be top heavy. You might like this being a Ghostbusters fan but I’m trying to create an altar for Gozer (seran wrap/packing tape) and a few small store bought skeleton dogs and off to each side of the altar the obelisks to hold my lights to shine on Gozer/dogs as well as my foggers.

@kevincrabtree3482 i don't. But it's just a piece of schedule 40 water pipe. That i welded a large washer to. Then, i welded a bolt to the other end and grinded it to a point.

@vanbooth9564 all kinds of places. The manufacturer, county auctions, marketplace,, ebay, garage sales, swap meets, and other slae sites.

@kevincrabtree3482 Thank you, I dont have a video on that one, but here is another one i made. ua-cam.com/video/iw9kku6QT6g/v-deo.htmlsi=g45V4SVb3M7Ell7h I do have a few other videos on how i make other structures that might help steer you in the right direction. Type in Halloprops it my other channel. Everything i make is made from foam wall baord and 1x2s to keep it light weight and easier to work with. If you need any suggestions, let me know. I'll try to help.

@leejenner3810 there're not bad for the price for what they can do.

@@bluedakota80 I'm well happy my family think I'm off my nut with the light bars about £38.89 paid

Yeah brilliant I can run all my light bars now my family think I'm off my nut though people think where to collect light bars

@aprilh691 i used caulking on the whole roof. I used nails where i had foam on foam. And screws where it was over the wood framing. Those were mainly to hold until the caulking dried. Im adding a link to my more detailed video if you wanted to see more of the fab. I still didn't show the roof. On how i held it to the framing. ua-cam.com/video/8xBSqeq3948/v-deo.htmlsi=4b9QKBbE-Gq5i__N

@@bluedakota80 thank you! Love your videos! I built a sleepy hollow bridge out of wood and foam and need to be able to assemble and disassemble it so I can store it. I was looking for ways to attach the foam roof. I might use bolts, but am not completely sure yet.

@aprilh691 you can glue wood to the foam. And when you set it on your bridge, you can do screws. Then when you take it apart. The roof with those pieces of wood will come off together.

@@bluedakota80 thank you!

@mbaer5 Thank you, Same here. I like the slower look over the led.

@@leejenner3810 New Version DC 12V 50A 600W Switching Power Supply Adapter 110V AC to 12V DC Converter Power Supply Transformer PSU for 12Volt Motor Pump CCTV Security Camera Car Stereo 3D Printer and More 12V Device a.co/d/iz5nPcG this is the link to Amazon. This is the same as i have just in silver

@leejenner3810 if the link dont work, it's a mysweety 600w(50/60HZ) Dc out 12v 50A

@@bluedakota80 thank u very much I have a look love your lightbar set up

@leejenner3810 you're welcome. Thank you

@tylerhair9067 you're welcome, If you have any questions, let me know. Did you see part 1 to see how i made the front and bricks.

@@Imtravis-t5o thank you

@@bluedakota80 no probs

@@pennycaschera203 thank you

@ameg7571 to be honest i haven't seen one of those with a holigen bulb in it. Most are a quarter turn incandescent light bulb. Either type you should be able to go on ebay or Amazon and type in the style and you should be able to find something that will work. I found these on Amazon not sure if this is what you are looking for. BA15D Double Bayonet Sewing Machine LED Light Bulb 5 Watt Daylight White 6000K Non-dimmable AC110V-130V (Pack of 4) a.co/d/7eBbYnL

@@bluedakota80 thank you so much Sir, I appreciate this link

@shawnramsey8264 🤘 Oh yeah

@robvader theres not much in the way of links. Just about everything I used, you can get at Home Depot. The main parts is 3/4 foam wall board. You can use the style with the foil or the style without. The one without is normal a pink or blue color. The glue i used is from Loctite PL 300 caulking that i got at Home Depot. But any siliconized acrylic caulking will work. Then i get a box of 3" nails. Those aren't specific, just a nail. Its purpose is to hold the parts while the caulking dries. All the paints are latex house paint. Indoors or out works just fine. After all, they are not supposed to be perfect looking. The pray gun is from Harbor freight. They are cheap there. If you wanted to do the ball on top. I got those from Hobby Lobby they always have their Christmas stuff out super early. They are the large 6" Christmas ornaments. And last the fence. I kept those simple. Those are made with 1x2s from Home depot as well. And painted black and brown. Black for iron brown for rust. Depending on how big you want to go and how detailed they are, you can make two columns with one 4 x 8 sheet of foam board. In the design i made with leaving one side open for lights. Feel free to ask anything. I'll help with any questions you have.