Відео

Yet another one done wrong. You didn’t measure the stack height

that was very good man. thanks i just did a god damn indo on my own cause someone stop short and i slam my font and did a indo and my front fucked....

i hav ducatin 795 accidentally detached the wiring from the connector now a cannot insert it due to lock of knowledge on the arrangement of the wiring

sir can you view the wiring arrangement coming from the body connector of fuel pump 1234 wiring insertion

I just need to remove the stator cover because there was a hole in in it, the stator has this white substance around it is that normal?

THANKS FOR THE VIDEO!

Hello, Thanks for This!!!! Great job!!!!

That’s a street twin not a speed twin…

Doesn’t look too hard. Thanks

Hi mate, thanks for the video. Did you manage to make it work with the last plate not offset? I'm having the problem that how the service manual tells to assembly offset does not work, but they way you did works instead. Cheers

Good complete mounting screw info. I fail to pry the cover excluding the longest screw. Now I know. TQ

NO NEED TO REMOVE THE ROTOR!!! After removing the side cover, the remaining two allen screws can be removed through the holes in the idle gear!

Thans for the video.just bought one.

Hello, thanks for this! Do you need to drain the oil before doing this work?

Hey hopefully someone can give me a answer to my problem ima try to break it down best as possible, So I have a 2019 Yamaha MT 09 that has 18k miles with a few mods like a ECU Flash, SC Project Exhaust, Quick Shifter, K&N Filter.. When im in my higher gears mostly going fast giving it full throttle my bike will rev higher than supposed to while losing power but I’m still able to up & down shift with no problem and take off in 1st gear with no delay I was told it’s most likely my clutch plates but the dealership wasn’t 100% sure they said they never heard of this problem if you was having these issues as well or know what’s going on I will really appreciate any advice..

Missed the gasket install

Couldn't watch this due to the STUPID music !!!! wtf ....

This video is garbage. It does not teach you anything!

I heard you need to soak the new plates in oil for at least a few hours before installing them.

You skipped removing the cover. That's the hard part cause of the gasket

The last friction plate is suppose to be off set

thanks chris my starter motor finally failed

Thank you so much. I have to do this at a friend of mine's bike because he bought a bike with a bad stator. This is a lot easier than doing it on one of my Harleys

Thanks I have an issue on a 2015 Scrambler, I'll watch those rollers on the removal.

Did you need to scrap old gasket off the engine mating surface?

Everything you showed is basically common sense. How about showing the most difficult part for most people which is getting the cover on and aligning the pull rod and the pull lever correctly. Or the proper order for stock plates...

Perfect

Excelente video me ayudo mucho. Muchas gracias.

Ducati key cover：ua-cam.com/video/x3n-0fOxj0c/v-deo.html

How did you remove the bolt from the rotor?

Can you pleas tell me what is the order to re install rhem agein ?

Where did you buy the parts

Nice. Good tutorial!

thanks for this! I'm having to do it the first time and it's great to see your video

do you have the torque specs for the bolts?

So when removing the fuel hoses does the tank need to be 100% empty or is there some kind a plug because I have a full tank and would hate to have to go thru the process of draining it

Hey thank you for this video. I was changing the battery on my Ducati 796 & your two minute video was so much more informative than the owners manuals complicated instructions

That’s the intake you took out in the front

Dumbest video ever

Do know d tourque specs for d spring bolts

It’s a street twin, not speed twin

coooooooool

Hey awesome video! I just wanted to make sure if I want to change my battery, I should stop at 1:49 right, or do I need to do the rest? and also what tool sizes do I need exactly? from what I saw in the video, 3mm hex allen key, 5mm hex allen key, and 8mm to remove the bolts, do I need more than that?