Відео

คุณคิดว่ายังไงฉันจะลองหาตลาดใหม่ในเวียดนาม

Blue angels not as good as red arrows

this was my first ever airshow ive been to, it was a crazy feeling during the f 22 demo feeling the rumble of the engine.

I was there I saw this live a few hours ago.

Nice video! One correction, these are F-18 Hornets rather than Phantoms.

Amazing! You’re video certainly captured the action.

I can certainly say without a doubt that it isn't a prop problem. Looks like probably a bad esc or like someone else mentioned motors may be damaged

Possibly the pin underside of the motor is pushed out just try and push it in. If that’s not the case then your entire AIO all in one board needs replaced this happens a lot with Emax tinyhawk boards

Bad esc

First try turning the motors by hand and making sure the motors are not grabbing as they could have debris or warped bells. If not that then access the AIO and ensure the motor wires have good connections to the aio. If they are connected fine then you should remove props, connect lipo, connect to betaflight, access the motors tab and test all motors using the slider bars and see if the motors are bad. If they are still not running right then you should check the escs by using the same steps you just used for betaflight but connect to blheli and make sure all four esc are detected. If you89 do not see all four escs then the aio will have to be replaced..

How was this fixed?

Definitely check your transmission fluid level, you will need to purchase a sold separate dipstick. It is very very common for the transmission wire harness gaskets to break, causing a leak and problems transitioning

Having the same problem but with the T-12 jumper. any ideas.

Could you do A step by step video on calibration on press/level with the Trex?

Can you do some more videos on flow, level, and temp on calibration???

Can you show me all block mode because I did same but nothing happened simulation

Actual block mode can you show me

Fuell pump?

I have the exact same problem even using the bind button and yes I connect the battery at the same time. Same thing happens with the emax controller. I have two new Tinyhawk 2s and a freestyle also. I've bound other Quads to other transmitters easily like Spektrum. Seems like others struggle with emax also. I'm pulling my hair out trying to figure this out. Any help would be appreciated.

Hey did you fix it? im having the same problem

What about modes did you change it ??

bad motor,, check motor n prop screws , make sure not rubbing , maybe swap motors to see if it might be esc.. if its new contact emax good customer service i hear , never had to call them.. love my fs2 , quiet

min throttle wasnt low enough so i got arm switch to work but i think my stick are screwed up when i hit throttle up it does go up but i think right stick when i move it is also throttle.so i need to get sticks right and im set setting up switches was a breeze following you.

I have jumper T8SG 2.0 and i bound the freestyle with frsky.setup my switches on my ch5 mine isbackward G0 is on top but no matter i picked G1 and my other switches.BUT everytime i got to arm it the little red light next to blue steady light blinks fast like 3 times and nothing no arm at all,i had first tinyhawk setup like a champ im hoping its not the drone.can you help at all?i dont understand am i missing something in betaflight.the freestyle is brand new out of box.

I also purchased this radio Id like to see a better setup video using the Jumper T8SG and the Tinyhawk 2 and Freestyle

Here is how I solved it. It took me about a week working with EMAX support (which was very helpfull). Turns out I was binded but I had to setup the transmitter. I found these two videos very helpfull for programming my T8SG. ua-cam.com/video/gwKltefJBGA/v-deo.html ua-cam.com/video/NLo6K3vMKi0/v-deo.html So you have to set everything up in your Transmitter first, Main Menu > Model Menu > Model type MULTI > 30 mW power > Frsky Power on the freestyle, then just press the Bind pushbutton on the bottom of the freestyle quad or hold for 5 seconds, then select BIND on the Jumper Transmitter. When speaking with EMAX support they advised it should be FRSKY V8 (D8 equivalent in deviation) but my freestyle and Tinyhawk S seem to both work with just FRSKY. So once you have it binded, you need to setup your transmitter mappings Menu>Model Menu>Mixer> 1-AIL > Simple > SRC > and move your right thumb stick left/right. You'll notice the Source changes to AIL (curve should be 1 to 1) > SAVE 2- ELE > Simple > SRC > move right thumb stick up/down, SRC should change to ELE > 1to1 curve>save 3 - THR > Simple > left thumb stick up/down, SRC changes to THR > 1 to 1 > Save 4 - RUD > Simple > left thumb stick left/right, SRC changes to RUD > 1 to 1 curve > Save Then you have to configure your inputs in order to ARM the quad, so after you program 4-RUD, next input should be Ch5 (Arming switch) > Simple > highlight the SRC and click your top left toggleswitch down. The SRC should change to SWG1 > Simple > Save Ch 6 (horizon/beginner mode switch) > Simple > SRC> click top right toggleswitch down SWH0 should appear in SRC > SAVE Ch 7 (beeping (VERY IMPORTANT FOR BEGINNER FPV PILOTS AFTER CRASH)) > Simple > SRC > Click whichever toggleswitch you want to program this fuction to > 1 to 1 > Save Ch 8 (Turtle mode/flip over) > Simple > SRC > whichever unused toggleswitch > 1 to 1 > Save DONE WITH Transmitter programming. now connect your freestyle to your PC and open Betaflight, Go to the receiver menu and you should see your Transmitter is changing things input values! click in the Character Map text box and change that to AETR1234 Then you will have to program your switches. go to the Modes menu, try clicking your arm switch. You'll notice the little yellow dot at the bottom of the first bar moves. You want it so when the switch is down, the yellow dot is in the yellow moveable range, this indicates It will be active when pressed down. For the horizon/angle mode, make sure they are both set to aux 2 and as you toggle the top right toggleswitch, make it so whatever mode you want, the yellow dot and yellow slider area match. So when in horizon mode for me the dot is at the top of the range in the yellow slider range, and when in angle mode and i toggle the switch again, the yellow dot is at the bottom and the yellow slider matches. The videos linked also explain this. MAKE SURE YOU PROGRAM THE BEEPER TOO. I lost my freestyle on it's maiden voyage (first time using FPV goggles) because it ran out of battery midflight, and crashed into a ton of thick bushes. Had to get another one.

Hello, I have the same problem! How to solve? Thank you.

hey you ever solved this ??

If you give it throttle and the red light flashes. You need to arm it with 0% throttle. Did you set up your 5th channel to arm it? Mine stays sold blue even after binding.

I have the beginner RTF Tinyhawk and wiped the settings and reinstalled them but now can't seem to be able to Bind the RC to the Quad. Still looking for a solution. However, in watching you attempts you may want to try this: Set your RC to D8 mode/channel. Hold down the Bind button (I assume it has one), as you simultaneously plug in the battery, for a few seconds, then turn on your RC and looking down inside the quad you should see a little green light appear.

Do you not have to hook it up to betaflight?

I'm having the same problem I think that the light panel and motor need to be replaced, you can get them for $10 - 20 .

The same happened to mine. Looks and acts just like yours. I finally figured it out. The damaged leg on mine was bent. I discovered it by comparing it with the other three motor legs. I believe in your video your leg is bent also. When holding the machine level the motors should be perpendicular 90 degrees and mine was not and I believe I noticed the same looking at yours. I simply grabbed hold of the plastic leg holding that motor and twisted it until it looked straight. Went out and flew it and now it flies again.

I had this problem. I took everything apart, cleaned it with rubbing alcohol, resolder some loose wires, and replace all of the gears. After that, it worked!

Just replace that arm for like 10 bucks

this is my problem now too,, unbalance,, i replaced the motor,, the gear,, still the same,, garbage thing,, i paid more for this, and for me a beginner it look like a bad nightmare for me,it better the i bought from best buy a protocol dronium,, what a waste money for helimax,, don't buy it

I have one too and just fixed mine.

no, The cog has come disembarked from the motor shaft. Take the leg off the one that is running wierd then remove the cover that has the motor in it. pull the cog off and put some superglue or nail glue (if you have a wife) on the shaft then put the cog back on. Prob solved....

Seems one motor is malfunctional

Put a new set of props on. One of the back ones looked damaged.