Відео

1 hour is nothing.... no wonder my smaller batter died on me

Dealers: we added this dope pin stripe bro that matches absolutely nothing about the cars body lines that’ll be 899.99

Should use br2032

I bought a replacement TPMS set on Amazon and used the MotoScan app to program the bike along with the "wake up" tool gizmo. Worked like a charm!

Will it work with the 7volt vest liner?

where did you buy your 12Pack CR2032 Battery, CR2032 3V Lithium Battery with Solder Tabs? great video. thanks!

I bought a Frontier. Drained the radiator and engine block plush flushed the heater core twice, put it back together and barely had any heat. 3 years later I bought a $90 heater core and was about to spend my Saturday doing this job. Took it to a mechanic to have the a/c evacuated and he talked me into letting him do a flush instead. He did it for under a $100 and now its blowing REAL hot. Just going to return the core. Good video though. I was literally a day away from doing it myself.

I wonder if it’s the same on a 4 cylinder? 🤔

H7 55W is the correct one

for a 2017 this did not work for me. good news it is way easier. no need to remove the windshield in my bike keyless FOB for 2017 R1200RT. A bit of background.... strangely enough to use the flat plastic "spare key" you get with the bike you pretty randomly slide the key part between the top of the digital dashboard and the bottom edge of the NAV holder (there is no official "key hole" there). it is able to slide in slightly to the right of center. and if you slide it in there, and only there, you can start your bike with only having the plastic key (slid into that spot). and that means that is the spot for your rfid in your dash. so you start your bike (with the plastic key) then take that key away from the bike then hold the new fob at the same exact spot. you can almost slide it in there a bit if the key is laying flat along the top of the dash at the point and push it a bit will go a bit under the (lower right of the) nav holder. you can press and hold the bmw button until you hear a beep, or just watch the orange key symbol with the ? over it on your digital dash and it will eventually turn off. takes about 30 seconds once the new key is in the right spot. have patience. good luck!

Don't turn the engine backwards. This method only works if you turn the engine in the normal working direction.

Thanks for info I guess the other terminal just presses on the battery

Thanks for the video!

I tried this and it does not seem to work for me. Following all the steps I still get the yellow key with ? On dash. Using a newly programmed key from dealership with emergency key. Once I removed the emergency key out of range, the new key won’t start the bike. Any suggestions?

I can’t believe these companies go out of they way to make it difficult for us to replace the batteries so they can charge us an arm an a leg.

With a little more effort BMW could have made this impossible. I love this bike, I do all my own maintenance and services - changing this bulb is the most difficult task, I have changed 3 in 88,000 miles and every time its been traumatic.

I had trouble removing the throttle side clipped spring. Carefully guided a small minus screwdriver to apply greater pressure on the spring than my fingers could. It worked right away. Big relief. Hope that helps someone.

Tried a few times but can't get the plug to let go from my low beam light. I was pulling on it like crazy but it won't release. So that stopped me at step 1. Is there an extra step to release the plug in a 2017 RT? Is it clipped somehow? It seems to be.

I'm trying to get this done on my '21 RT with the TFT Is it the same process for that as well?

Hi, I believe the video is really good. I am doing the same project. What did you use as a sealant? Many thanks

Just had to take my 2019 r1250rt to the Dealer in Livermore to get the FOB programmed. Turns out, the speaker on the right side had to be removed in order to get the Key FOB close enough to the antenna to recognize it.. $130.00 in labor cost, and now it works...

Not sure if I missed it, what battery was pulled out? 2032? I saw that you put in a 2032.

Great video. You explained everything fully to a T

Is that one hour on high with both the pants and jacket liner running or is that just individually running or the other?

Many thanks!! Great help... saved a bunch of time!

You failed to show the most important parts.

What size is that charge port? Is that an 8mm???

Thanks for the video!

Did you reuse the old plastic heater core tubes or get new ones?

is the wakeup tool absolutely necessary?

thanks for sharing, .. Question about the denali lights, did you use their clamps for the lights or your own?If, yes.. can you tell me which lights you have on your bike please? Cheers

What was the connection procedure for the lower contact? Did you also solder it ? Thanks

Thanks for posting this. I just managed to change the bulb in about 15 minutes....Great!

Awesome job dude!

Hi Ayman, do u know if this new key from the factory requires its to be Pre program with our VIN before we program it with the bike? I am thinking to buy the key from a non-bmw dealership but i am worried this key might need some pre-VIN programming before we program it together with the bike. Do u have any idea? Thanks

Hey bro I just changed out my low beam on the 18 RT. I used Phillips H7. What a pain in the rear. Lol. I had to remove Oem horn due to it being more forward because of my Denali air horn. I found the throttle side spring wire the hardest to get back on. It’s done now, maybe led bulb in the future.

Me and anthony owe u a beer!!

Will this work with out a hook up to the motorcycle?

Absolutely love this Video😂 but Why is mine Only beeping on the wall?😳😕

Quick n imformative thumbs up mate

Thanks your video was very informative I just replaced my heater core on my xterra my self my mechanic wanted to charge 850 an claim a two day job I done it in a couple hours me an my brother

I flushed my radiator and engine block with my hose, refilled system with distilled water, ran until hot, and flushed that a couple times (it was real bad). Refilled with radiator fluid.... and I still have crappy heat. Going to flush heater core and if that doesn’t do it.. we’ll then I greatly appreciate this video

Thanks! the tubes broke when the engine got hot, by passed for now and new engine, but this will help allot when I replace core.

Thanks for taking the time to make this video.

If you are looking for this product, go to www.Gerbing.com then "12 volt Accessories" the scroll down to "Gerbing 12V Heated Clothing Battery Kit 10000 mAh"

Good video...I’d also suggest putting it in the center stand. I know yours was, but wanted to make it clear to others that putting it on the center stand will help. Otherwise the forks get in the way.

I think i can make it work if get two plastic tubes and 8 bolts or screws

hello sir i have very similar setup, do you know the part number for those 8 heater core screws or bolts cant find them greatly appreciated thank you .everything was pretty much the same but that plastic piece its aluminum that doesn't detach had to cut it just to remove it . the new one they gave me has the screw holes but can't find online

Would this work for a Milwaukee heated jacket?

My fob was not working after I’ve change the battery. This video works for me. Thanks!!!!