Відео

if you're still using the ev800d - can you share your video settings? I mean brigthness, colour, contrast etc.?

I like the Cobra V2 better. Thanks for the comparison.

hey man! I just finished mine and I was wondering if the CG marks are properly located, what are your thoughts about that? Mine is aprox at the same weight as yours and balances fine with a huge brick of a battery on the nose.

Looks like youre in the Austin area... lets fly our 2400's together hehehe

cobra dvr doesn't seem that much better...I assume in person it's another story though

Witam. Jaki pakiet lipo? Mam phoenix volantex 2400 ale bez fpv

эксклюзив

Absolutely great thanks for sharing. Just got one of these 2400 but do not yet have HD vtx/ground view.

What is your Settings for ASA? I have issues with ASA on my Ender 3 S1 Pro small prints looks good but bigger prints they get loose from the bed after hours. After i set the Flow to 80% i got good result but the print get warped on the corners.

You need to use a design with more iner support structure i had this same problem when printing thin wall in abs

Super fun diving with you! Thanks for sharing your video!

Very beautiful, like in the Maldives

Quality of dji03 is 🔥🔥 nice flight!

Such a nice plane, nice flight mate!

P R O M O S M 💯

Are you still flying your twinky?

Bravo !

I flew over you right as your were making ur landing approach.

Gee. you add the big draggy video camera on top, leave off the spinner so there is a big hole in the front, and strap whatever that blob is onto the outside of the tail. This at least TRIPLED the drag of the plane, so yes, it will come down 3 times faster than it would if you kept it clean

Красиво!

Со звуком было бы круче

wow,. thats very cool,..

Que vídeo fantástico rapaz. Eu não sabia que um drone como esse poderia ir tão alto 😅😅😅

Thank you for the vid.

Does the model s instill trust in 3d printed planes? Is it a solid every day flyer? What are its week points? Thanks.

Nice video! I caught some of your shorts on printing a plane in ASA, I've just started messing with ASA, so far I haven't had much luck, I have an ender 3 also, can you tell me if you used any glue or anything on your textured PEI sheet to get the ASA to stick?? Just installed that PEI bed, haven't tried the ASA on it yet. Any other tips you could offer on the ASA printing would help... I couldn't leave anything in the shorts as there isn't a place for comments.... Thanks!

what hotend are you running? Also what fan shroud is that?

Место конечно приятное, что зимой, что летом. Есть где пофристайлить и разложиться в хлам :)

That is satisfying

Which one is better, this or twinky

What battery are you using

what flight times can you get with this plane?

Hello! Could you tell me the max pitch setting (in PID TUNING)? on the other hand, know what your climbing grade is and finally know if you went out with a motor at 2000us. Thank you so much!

Is the bad glide ratio due to it's weight? Would you build another LW-PLA plane?

Nice video, would you think it can fly with an 1850 6s battery and 2207 motor?

PLEASE RE-DESIGN THIS PLANE WITH CENTRAL PART AXECTLY ALIKE A CAR & WINGS ON BOTH SIDES. THEN UPLOAD THAT MODEL ON UA-cam.

nice setup, where did you get the fpv canopy from?

Nice job!

Есть в планах сделать гидроплан?

Thank you for sharing this detailed video about your build. I am in the process of building a few Groms. Could you share a link to the STL for the O3 Pan and Tilt setup you used? It looks very compact and solid.

Какой же это "Гром"?! Это Strix Goblin. Он хорош в любом виде! Хоть из пластика и ЕPS, как в оригинале, хоть на 3D-принтере напечатанный. Это модель-бестселлер.

Noice

Super nice.

Can you put a link of the pan and tilt camera stl.?

And which is better?

Great video. Have a new Ender 5 S1 and this will be the first project. Printed a few 3d printed planes on my CR10-V2 and looking forward to getting this in the air. Thanks for sharing.😀

Hey Alex, did you make any upgrades to motors and propellers ?

Какая у него круизная скорость?

бьютифул!! )))

Fantastic you are getting good results with that Grom setup!