Відео

Is this process the same for a automatic trans? 2013 Subaru Outback. Pretty sure it's the Viscous Coupling making the noise.

Thanks for the video and the education. Cheers

He dead forgot the ring 😭

Ahoj, prosímta ty si Čech? Vedel by si mi dať na teba nejaky osobny kontakt? Potreboval by som poradiť..

Will this be similar on a 2016 Crosstrek? Mechanics are quoting me 3-4 thousand dollars for this job and the part is only like $700

This is n47 engine?

Hello, i have question about variator, did i need set it up some how?? Or just to tighten a screw and set Up Marks ?

Would you know how different an automatic Center Diff replacement would be compared to a manual?

watched the video a few times … it gave me all i needed to accomplish the job myself … thank you for making the video … also thank you for that 8mm rod slide hammer info, that came in handy 🙏🙏🙏

dude talking in background super annoying

I have just compmeted the timing chain i have built the car back up and now its not starting... i have my computer plugged in but cant see any fault codes ahhhhhh.... my timing marks where spot on and everything went smooth... im lost now haha

Браво дружище ! Невероятно !

This video was super helpfull thank you. Quick question is there a reason the simplex chain was made for theese vehicles was the original roller chain not good 🤔

Terima kasih

👍🏻👍🏻👌🏻💪🏻

Nice work

Soo good Chettayii ❤❤❤👌🏻👌🏻👍🏻

What are you spraying on the casing after you've cleaned it off? And what kind of gasket paste did you use?

I mean, you didn't show how the syncos actually work. For that, you should have the free spin gears running and only then we would be able to see how synchronizers work. But, thanks anyway

Meu câmbio desse modelo na ecosport faz barulho em ponto morto, ja troquei os rolamentos internos, volante bimassa mas o barulho insiste, só para quando piso na embreagem, será que posso colocar um óleo com especificação mais grossa, o 75 w acho muito fino para o Brasil sendo um pais muoto quente, percebo que com o câmbio frio não faz barulho, quando aquece faz

👏🏻👏🏻👍🏻

So much Good baby ❤️🤞🏻

I'm having similar problem on 2010 subaru outback mt where feels like the front end is welded diff at slow speeds and locks up around corners... I'm starting to think it's the vc..... I did a clutch on the car and notices cv alxes need to be replaced did that now I'm having this lock up issue😮

💪🏻💪🏻💪🏻❤️

isnt there a bearing preload that needed to be accounted for?

Great work 💯 baby 💪🏻💪🏻❤

Hello Sir, we have a similar problem with our 2005 Mondeo 2.2 TDCi. Engine turned off at low load and refuses to start. Fuel pressure is too high (around 400 Bar) even after replacing fuel pressure regulator (ours seems slightly different, because of facelift). The sealing ring of the fuel pressure was damaged, so we replaced it too. ECU still refuses to start because pressure is too high. Maybe it's a bad injector or cable? High pressure pump is fine, no shavings. Error code P1608 (bad cables?), P2288 (pressure too high) and P2623 (injector control pressure circuit open (also bad cable?). Any advice? Thank you so much.

Hello, do I have to bleed to start?

My car is leaking oil through the starter motor, what could it be?

Guys. Stick to the press

U made it look easy...tempting me to try it on my own...thought I'm afraid I'll head in to some unexpected issue and be left half job done. I myself had replaced too the cv axle thinking it was the problem..yet..

Okay so which one is spinning by default aren’t all of them spinning together

Excellent explanation Thank you ❤❤

Open bleed screws when draining too? Another bleed screw on heater pipes on bulkhead

what if the fluid IS frothy at the end?

Price kitna ka he

Oh is there i30?

not replace the upper holder? you'll be doing it again in no time :-)

Radiator cap 1.1 bar or 0.9 bar ?

That's a work up for an annual service item.

Can I change valve seals without removing the head with compressed air?

Thank u so much ❤ from Algeria

I need one of these, Mine's starting to clunk tight turns park speed. Replaced front cv shafts but still clunks, Anyway good content i know now what's the problem.👍

I replaced the fuel filter with help of your video. But now car not starting. All connections are ok

Oven cleaner is also possible I have heard.

Why change fuel filter ? What is the problem

👍

Awesome video!

acha kam ji

Good one baby ❤❤❤