Philipp Galvan Design
Philipp Galvan Design
  • 189
  • 852 366
Ladybug Tut. #24 - Rhino sun with Ladybug and More
Philipp continues the Ladybug Tools course in this tutorial, covering advanced sunlight and shadow analysis tools in Rhino and Grasshopper. Here’s a breakdown of the key topics:
Reintroduction of Legacy Tools: Tools like "Set Rhino Sunlight" and "Surface Ray Tracing" have been resurrected in the latest versions of Ladybug Tools (1.8+). These tools allow precise control and animation of sunlight within Rhino, enabling users to simulate sunlight by minutes, hours, and even years.
Surface Ray Tracing: This tool tracks how sun rays hit and bounce off a 3D model, useful for analyzing potential lensing effects and solar impacts on design.
Solar Envelope Tool: Determines how obstacles (e.g., buildings) cast shadows and block sunlight. It helps architects understand where to build without infringing on solar access rights.
Sky Mask Tool: Visualizes the percentage of visible sky from a given point in the project, allowing for optimal sunlight exposure.
Practical Tips: The video covers essential settings in Rhino, such as adjusting sunlight quality and shadow sharpness, controlling lighting in viewports, and animating sliders in Grasshopper for dynamic sun studies.
Upcoming Tools: The creator hints at exploring "Shade Benefit" and "Thermal Shade Benefit" in future videos, focusing on optimizing output visualization.
Hashtags:
#LadybugTools #Rhino3D #Grasshopper3D #SunlightSimulation #SolarEnvelope #ArchitectureVisualization #3DModeling #SustainableDesign #BIM
Disclaimer: The content in my videos is for informational purposes only and does not replace professional consultation. I do not take responsibility for any decisions or actions taken based on the information provided in these videos.
Переглядів: 689

Відео

The Key for a successful SubD model - Rhino3D - Intro
Переглядів 235Місяць тому
Mastering SubD Modeling in Rhino: Precision vs. Topology Have you ever wondered what sets a professional 3D model apart from an amateur one? It’s not just the software but something deeper-structure and topology. Key Highlights: Precision Isn’t Everything: In early concept designs and organic shapes, SubD-modeling can offer more flexibility than NURBS. Advantages of SubD Modeling: Editability: ...
SubD Modeling for Beginners | Rhino3d
Переглядів 2772 місяці тому
Chapters: What and Why: 0:00 Intro: 1:51 SubD Interface: 3:32 SubD Plane: 9:55 SubD Box: 12:22 SubD Symmetry 13:02 Subd Edge Loops: 14:51 SubD Remove Symmetry 18:21 SubD Soft Transform: 19:42 SubD Gumball: 20:38 Delete and Add Faces 23:20 Introduction to SubD Modeling in Rhino In this tutorial, I delve into the basics of SubD modelling in Rhino, a powerful alternative to NURBS modelling that of...
Perfect Terrain Models within Seconds - Grasshopper Tutorial for Beginners
Переглядів 5213 місяці тому
Perfect Terrain Models within Seconds - Grasshopper Tutorial for Beginners
Ladybug 1.8 Tutorial: Outdoor Comfort and 3D models #23
Переглядів 1,1 тис.3 місяці тому
This comprehensive video tutorial guides you through performing Outdoor Comfort Analysis in LadyBug tools 1.8. It leverages the Universal Thermal Climate Index (UTCI) to analyze outdoor comfort, but with an added twist - you'll learn how to incorporate a 3D model for a more nuanced analysis that considers shading from surrounding buildings. Chapters: 0:00 Intro and Channel Member Shoutout 2:05 ...
What the hell are Attractors in Grasshopper?
Переглядів 3274 місяці тому
Grasshopper Tutorial: Attractor Points This video is a beginner-friendly introduction to using attractor points in Grasshopper 3D. You'll learn how to: Create a grid of points Use the "Move" and "Series" components to manipulate points Craft data trees for complex operations Implement attractor points to influence object properties (like circle radius) Generate surfaces from your final geometry...
Ladybug 1.8 Tutorial: Mastering View Analysis #22
Переглядів 9895 місяців тому
Struggling to understand how much view your building offers or where to place surveillance cameras for optimal coverage? This video dives into the exciting new features of Ladybug Tools version 1.8, focusing on View Factors, View Rows, and Visibility Percentage. We'll guide you step-by-step through setting up these studies in Grasshopper. Learn how to interpret the results, including colorful v...
Outdoor Comfort Optimisation with Galapagos and Ladybug | LBT 1.9 Q&A
Переглядів 1,3 тис.6 місяців тому
This video discusses using Ladybug Tools, specifically focusing on limitations encountered while creating a script for outdoor comfort analysis. Here's a breakdown of the key points: Goal: Create a script in Ladybug Tools to analyze outdoor comfort and see if the building position can be optimized for better comfort. Steps Taken: Weather Data: Downloads weather data for a specific location. UTC...
Ladybug Tools 1.8 - Q&A and Troubelshooting - Part 1
Переглядів 9366 місяців тому
In this video, Philip tackles common problems faced by viewers using Ladybug Tools 1.8. He guides you through setting up a simple Honeybee model and choosing Radiance parameters. You'll learn how to: 0:21 - Apply Radiance parameters to a model 7:40 - Assign a sensor grid to a model 11:32 - Run a point-in-time Radiance analysis 12:19 - Compare the impact of detail level on results 14:49 - Import...
How to Install The Ladybug Tools 1.8
Переглядів 3,6 тис.6 місяців тому
This video is a guide to updating your Ladybug Tools plugin for Grasshopper to the latest version (1.8). Upgrading offers new features, bug fixes, and improved functionality. The speaker walks you through the entire process, including: Uninstalling old versions Downloading and running the installer Verifying successful installation Installing optional components (Radiance & Open Studio) Great f...
CFD Analysis - Case from Folder - Butterfly #21
Переглядів 8427 місяців тому
Struggling to manage your Butterfly cases in Rhino 7? Are you constantly recreating the same case setups wasting valuable time? This video is your one-stop guide to mastering the Butterfly Case from the Folder function! Learn how to efficiently retrieve and utilize existing cases, saving you hours of repetitive work and streamlining your CFD workflows. In this comprehensive tutorial, you'll dis...
Ladybug & Galapagos Combo Simplified! | Ultimate Ladybug Course #21
Переглядів 8197 місяців тому
Related Video: ua-cam.com/video/QF6frP9GDMI/v-deo.html Welcome back to a bonus tutorial where we explore combining Ladybug and Galapagos, addressing a common question in architecture. Most tutorials dive deep into complexity, but we're keeping it simple. In our last video, we delved into Ladybug's view percentage tool, questioning if we could facet cylinders for non-circular buildings. To do th...
Mastering Ladybug View Analysis: Exploring Design Thinking | Ultimate Ladybug Course #20
Переглядів 8678 місяців тому
Welcome back to the Ultimate Ladybug Course! In this milestone 20th video, celebrating 8,000 subscribers, we delve deeper into Ladybug's view analysis tool. Join us as we explore the intricacies of this powerful feature, unlocking its creative potential in design thinking. Using real-world examples, we demonstrate how to optimize window placement for maximum views while maintaining privacy. Fol...
#19 View Analysis is Underrated and Undervalued
Переглядів 8498 місяців тому
In this video, we delve into the critical aspect of view analysis in architectural design, focusing on the importance of considering views in hotel design and urban planning. The host emphasizes the significance of selecting views strategically, whether for guest rooms, rooftop terraces, or public spaces, as they greatly impact the user experience and urban aesthetics. Using Rhino software, the...
#18 Cracking the Code of Incident Radiation & Direct Sun Hours | Ultimate Ladybug Course
Переглядів 1,6 тис.9 місяців тому
Ever feel lost in the world of Ladybug's radiation studies? Don't worry, you're not alone! This video is your illuminating guide, helping you navigate the complexities of Incident Radiation and Direct Sun Hours. Unraveling the Mysteries: Beyond Sunlight Hours: Go beyond basic sun exposure with Incident Radiation, revealing valuable insights into energy potential, building performance, and even ...
#17 Why Sustainable Design Starts with Sun Studies (and Not Just Pretty Pictures)
Переглядів 9369 місяців тому
#17 Why Sustainable Design Starts with Sun Studies (and Not Just Pretty Pictures)
#16 Bonus 3 | Site Modelling for Ladybug Analysis
Переглядів 5719 місяців тому
#16 Bonus 3 | Site Modelling for Ladybug Analysis
#16 Bonus 2 | Sketching is Thinking | for Architects, Landscapers and Designers | 2 of 2
Переглядів 27610 місяців тому
#16 Bonus 2 | Sketching is Thinking | for Architects, Landscapers and Designers | 2 of 2
#16 Bonus 2 | Sketching is Thinking | for Architects, Landscapers and Designers | 1 of 2
Переглядів 45910 місяців тому
#16 Bonus 2 | Sketching is Thinking | for Architects, Landscapers and Designers | 1 of 2
#16 Bonus | Conceptual Bubble Diagrams - Gift or Curse | Turn your Brain on
Переглядів 65711 місяців тому
#16 Bonus | Conceptual Bubble Diagrams - Gift or Curse | Turn your Brain on
Grasshopper Fundamentals Beginners | Your First Script | #03
Переглядів 604Рік тому
Grasshopper Fundamentals Beginners | Your First Script | #03
Grasshopper Fundamentals Beginners | How to link objects from Rhino into Grasshopper | #02
Переглядів 2,7 тис.Рік тому
Grasshopper Fundamentals Beginners | How to link objects from Rhino into Grasshopper | #02
Grasshopper Fundamentals For Beginners | The Interface | #01
Переглядів 694Рік тому
Grasshopper Fundamentals For Beginners | The Interface | #01
#16 Direct Sun Hours - All You ever Need - Ultimate Ladybug Course - LBT 1.6
Переглядів 4,7 тис.Рік тому
#16 Direct Sun Hours - All You ever Need - Ultimate Ladybug Course - LBT 1.6
#15 Ladybug Sky Matrix Tools in Grasshopper 3D - Ultimate Ladybug Course - LBT 1.6
Переглядів 4,2 тис.Рік тому
#15 Ladybug Sky Matrix Tools in Grasshopper 3D - Ultimate Ladybug Course - LBT 1.6
#14 Demystifying the Psychrometric Chart in Grasshopper Ladybug - Ultimate Ladybug Course - LBT 1.6
Переглядів 1,5 тис.Рік тому
#14 Demystifying the Psychrometric Chart in Grasshopper Ladybug - Ultimate Ladybug Course - LBT 1.6
#13 Mastering Monthly Charts - Ultimate Ladybug Course - LBT 1.6
Переглядів 932Рік тому
#13 Mastering Monthly Charts - Ultimate Ladybug Course - LBT 1.6
#12 Everything about the hourly chart - Ultimate Ladybug Course - LBT 1.6
Переглядів 962Рік тому
#12 Everything about the hourly chart - Ultimate Ladybug Course - LBT 1.6
#11 Enthalpy and more - Ultimate Ladybug Course - LBT 1.6
Переглядів 563Рік тому
#11 Enthalpy and more - Ultimate Ladybug Course - LBT 1.6
#10 Optimizing Solar Panel Orientation with Ladybug + Galapagos - Ultimate Ladybug Course - LBT 1.6
Переглядів 3,9 тис.Рік тому
#10 Optimizing Solar Panel Orientation with Ladybug Galapagos - Ultimate Ladybug Course - LBT 1.6

КОМЕНТАРІ

  • @FatemehHedayati-r1f
    @FatemehHedayati-r1f День тому

    Hello Philip, thank you so much for the explanations. I had run into issues a few times, but now I was able to install it easily

  • @safaeoulmouden8103
    @safaeoulmouden8103 День тому

    Hello Philipp! I’m working on energy performance optimization using simulations. I’m currently trying to implement the Sobol sampling method in Grasshopper to study different design parameters. I’m facing challenges with running simulations for each sample and saving the results properly. I’d really appreciate any advice or guidance you could offer on this process. Thank you!

  • @jav_mx9856
    @jav_mx9856 5 днів тому

    How install in Rhino 8?

  • @abhishekmhatre648
    @abhishekmhatre648 8 днів тому

    Thanks a lot broski <3

  • @PhdQuicktips-DZ
    @PhdQuicktips-DZ 12 днів тому

    Hi Galvan! I like your channel! Thank you

  • @arghavanjalayer1011
    @arghavanjalayer1011 12 днів тому

    Hello and thank you for these tutorials, I got this error at ''loadporbsvalue'' ''C:\Users\username\butterfly\ Failed to find probes folder windtunnel\postProcessing\probes do you have any suggestions? Thank you

    • @PhilippGalvanDesign
      @PhilippGalvanDesign 11 днів тому

      Not sure. Did setup the Bluecfd environment? Are you running Rhino in admin mode? Did you run a calculation successfully before?

    • @arghavanjalayer1011
      @arghavanjalayer1011 11 днів тому

      @@PhilippGalvanDesign yes like your video, but I didn't wait for the calculation as it took so long and it was running and running and I didn't know when will it finish.

  • @mdrajibulhoque2789
    @mdrajibulhoque2789 13 днів тому

    Is there any cyclone simulation

    • @PhilippGalvanDesign
      @PhilippGalvanDesign 13 днів тому

      Not that I know at least not in Butterfly. What you like to analyze?

    • @mdrajibulhoque2789
      @mdrajibulhoque2789 12 днів тому

      @@PhilippGalvanDesignwind flow

    • @mdrajibulhoque2789
      @mdrajibulhoque2789 10 днів тому

      @@PhilippGalvanDesign yes

    • @PhilippGalvanDesign
      @PhilippGalvanDesign 10 днів тому

      Butterfly can only analyze one wind direction at a time... Although you could more than one inflow but that would not simulate a cyclone. Butterfly works like a physical wind tunnel. Maybe you need to modify your question. Instead of wanting to simulate a cyclone which is pretty unpredictable maybe think of what problem you want to solve first.

  • @oykuongoren7223
    @oykuongoren7223 13 днів тому

    Hi, it was a really helpful vide as always. Have you ever got error in annual daylight that Radiance fails to load one of the files when calculating the direct sunlight. I'm having it and couldn't figure out

    • @PhilippGalvanDesign
      @PhilippGalvanDesign 11 днів тому

      Hmm not sure. Haven't encountered such problem. Let me know if the problem persists.

    • @oykuongoren7223
      @oykuongoren7223 11 днів тому

      @@PhilippGalvanDesign thanks for replying. yes unfortunately it continious. I shared the post in ladybug tools dicourse platform under the name in oyongoren. I'm trying to try every suggestions 🙏

  • @Ahmed_7afez
    @Ahmed_7afez 15 днів тому

    Hello Philipp I tried to follow your steps but when i tried to connect all geometries blocks as walls, inlet & Outlet to the block case from geometries i had an issue to connect all geometry together it took only one of them Please help me with that

    • @PhilippGalvanDesign
      @PhilippGalvanDesign 11 днів тому

      You might need to check the mesh resolution of the objects. Maybe you need to send me a screenshot if the problem persists...just note that I'm traveling at the moment and won't be home before in 2 weeks.

    • @Ahmed_7afez
      @Ahmed_7afez 11 днів тому

      @@PhilippGalvanDesign Thanks a lot for your reply Have a great travel 🤗

  • @ClintWorton
    @ClintWorton 16 днів тому

    Thank you for this!!!

  • @aCatIsLeo
    @aCatIsLeo 16 днів тому

    thank your lady bug guild,its help a lot

  • @odedabir
    @odedabir 24 дні тому

    Hi Phillip, on Rhinolands there r two options to purchase: Rhinoland or Lands Design. which out of the two you are using? Thanks, Oded

    • @PhilippGalvanDesign
      @PhilippGalvanDesign 24 дні тому

      I use Landsdesign. Rhinolands is basically a combo. Rhino + Landsdesign. In case you don't have Rhino you could go for that option. it doesn't have more functionality...

  • @faisalazamkhan3240
    @faisalazamkhan3240 28 днів тому

    What are the benefits of memberships

    • @PhilippGalvanDesign
      @PhilippGalvanDesign 26 днів тому

      No specific benefits. It's for me to survive as a channel and I will prioritise members questions and suggestions.

  • @devikaarun5207
    @devikaarun5207 Місяць тому

    thankyou!!!!! good video you explained in very easy way and easy to understand but i have one probler which is (1. Solution exception:WindowsError ) is there any solution ?

    • @devikaarun5207
      @devikaarun5207 Місяць тому

      12:59 here the problem occurs while toggle set to true

    • @devikaarun5207
      @devikaarun5207 Місяць тому

      please help me its important

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      Did you follow the installation properly. Which version of bluecore CFD did you install? Did you follow the steps to setup the bluecore CFD environment. And are you running Rhino in admin mode?

  • @luizmendes1625
    @luizmendes1625 Місяць тому

    Hi Philipp. Thank you very much! I've a problem. I created my energy model, and inserted brise-soleil (sunshade) with the "HB Louver Shades" node, as you taught. But when analyzing the building with and without brise-soleil, the result of the operative temperature in the "HB Read Room Comfort Result" node is the same, as if the brise-soleil had no effect, do you know what that could be?

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      I'm not sure I haven't looked into HB for a while. I'll check it out when I get to. Is the the 'HB read room comfort result's part of HB radiance or HB energy? Also is your shading inside or outside the glancing line?

  • @mackenziemodde5439
    @mackenziemodde5439 Місяць тому

    Hi there, why would my heatmap be giving me in the inverse of color. Where hot areas should be using a shade canopy it provides less hot areas and where less hot areas should be (under the shade) it is bright red...

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      You might need to check if your surface is not upside down. Or you maybe have a different colour legend code. What is the temperature under the canopy and what is it next to it? Are your canopies solids? Which climate are you testing? (Which geographic location) Which time of the day are you testing?

    • @mackenziemodde5439
      @mackenziemodde5439 Місяць тому

      @@PhilippGalvanDesign Turns out I was testing for 7 pm in a climate where the sun had set, so this would makes sense. Is there a way for calculating WBGT as opposed to UTCI?

  • @georgeneverland896
    @georgeneverland896 Місяць тому

    Hi! In order to analyse ground surfaces I have to extrude them into solids?

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      No you don't need to extrude them into solids. Except if you use Honeybee.

  • @nanox4520
    @nanox4520 Місяць тому

    and URBANopt CLI? is not necessary?

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      @@nanox4520 Not necessary except you want to run Dragonfly models through E-Plus... I never used it as it is very specific.

  • @orcunfindik1195
    @orcunfindik1195 Місяць тому

    hi many thanks for the video! I was wondering if I can use the hb utci confort map component to make an estimation for temperature levels and so efficiencies of the PV panels that are located at a certain level?

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      The comfort map is the perceived temperature. But for PV panels the most important aspect is the exposure to the sun. Not the temperature. But you should be able to calculate a heat map just from the surface temperature only. It's an interesting topic.i might make a video.on this.

  • @oscarjames5056
    @oscarjames5056 Місяць тому

    Hi Philipp, When I run the Direct SunHours component, I seem to get an extra timestep. For example, if I am analysing 1hr with 6 timesteps (every 10mins), I seem to get results greater than 1hour (e.g. 1.16hrs of sunlight between 12pm-1pm). Do you know why this is the case?

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      I am wondering if you need a 10 minute interval for a Sun Hour study. The idea is to calculate hours together. Except you want to animate the Sun exposure over time. However I think the reason why you get a seventh step has something to do with the way how ladybug calculates this. It adds values for points in time. So for example. The first value is captured at 12:OO then 12:10, 12:20, 12:30, 12:40, 12:50. (6 values) Now because you define the hour as 12:00 to 1:00 you get a seventh value at 1:00. This value supposed to be part of the next hour. 1:00, 1:10 1:20 etc... Now again I don't see much reason why I would calculate an hour in 10 minute interval if I can just calculate 1 hour with an hour interval... You get the same result...

  • @devikaarun5207
    @devikaarun5207 Місяць тому

    thing is i followed same procedure but my structure is highrise structure with detail wall and multiple floors which i combined and made a bloock and group of that so when i select in brep its not getting selected as well there is error ? i am not able to send you picture of that on youtube chats will you please help me on that ? please send me mail id so i can send you the actual doubts and question regarding shadow as well wind analysis ????

  • @alicelim2225
    @alicelim2225 Місяць тому

    Hi! Is there a way to adjust the albedo/reflectivity of the material and obtain the value of mean radiant temperature to see the impact and relation?

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      In theory I should be possible but I haven't tried that myself. I am quite busy these days. But if I come across it I'll try

  • @devikaarun5207
    @devikaarun5207 Місяць тому

    i have doubts regarding installation of cfd .. it didnt work on my pc after following same procedure and thz video is 3 years old maybe not working on new rhino.. so please upload trying new version of rhino and grasshopper using same procedure .

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      Which version of rhino are you using. And which blue core CFD version did you install?

    • @devikaarun5207
      @devikaarun5207 Місяць тому

      @@PhilippGalvanDesign same version 2017 bluecfd and rhino 7

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      Are you running Rhino in admin mode?

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      And did you create the CFD environment?

    • @devikaarun5207
      @devikaarun5207 Місяць тому

      @@PhilippGalvanDesign how can i check thz ?

  • @faisalazamkhan3240
    @faisalazamkhan3240 Місяць тому

    This is very useful particularly how can we use ,it in the design and extract more from it.

  • @faisalazamkhan3240
    @faisalazamkhan3240 Місяць тому

    can you also include 5 minutes ,how we can get benefits of these data.

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      Yes good idea, I will do a follow up video at some point to explain use cases.

  • @MonaMostafaMostafaAmin
    @MonaMostafaMostafaAmin Місяць тому

    Hello Philipp, Thank you a lot for your videos. Great work! I have two questions. 1- Don't you need to also limit the simulation period for the data of the fract. solar exposure? 2- How can we average data for each point on the grid and plot one hourly chart for UTCI? I can only plot a chart for each point on the grid.

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      Question 1: The human to sky relationship doesn't require weather data information. It's the relationship between location and objects. No sun movement. Result is one number per point. Question 2: you need to average the list of values per point to get an average number per point. Then you need to flatten the resulting list to get a single list with one value per point. Not a list of lists with one value....

    • @MonaMostafaMostafaAmin
      @MonaMostafaMostafaAmin Місяць тому

      @@PhilippGalvanDesign Thank you a lot for your reply.

  • @naghamismail4780
    @naghamismail4780 Місяць тому

    Hi Philip, Thank you for this video, I have a question, how UCTI component has accepted the wind speed that has different length than the temperature and the relative humidity? Should not be the same size? Logically, you should take the probe points of the velocity and put it in the point of human to sky so that every probe point has utci and velocity, no?

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      Yes I'm using the probe points as my points for the human to sky relationship component... In the UTCI component I input the windspeed resulting from Butterfly. Not sure if I can follow your questions correctly.

  • @sevtapozyldrm8564
    @sevtapozyldrm8564 Місяць тому

    Hello Philipp, your videos are great, thank you very much. I followed every step and I think I got a good result but I'm not sure about the accuracy. I also indicated the north direction but there is equal amount of light coming from all directions. When I do the Lady Bug solar analysis on the same location, I see that there is a significant difference between north and south. There should be very little light coming from the north but in the daylight analysis it is the same from all directions. Why do you think this happens? Thanks a lot again

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      Daylight is different from Sunlight. With Solar analysis you can calculate the direct sun hours which doesn't include the skylight. Only direct light. Have you tried the solar radiation study in Ladybug or the Sun Hour study?

    • @sevtapozyldrm8564
      @sevtapozyldrm8564 Місяць тому

      @@PhilippGalvanDesign Thank you so much for your answer. I did solar radiation in Lady Bug

  • @invencibletheory
    @invencibletheory Місяць тому

    amazing! is there a way to bake the sun range of a specific period as a shape? so as to mark an outline where the sun hits throughout that period?

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      You might want to look at the Sun envelope in the new Ladybug 1.8. that might be able to do that.

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      Or at least help to get there.

  • @extrasausage586
    @extrasausage586 Місяць тому

  • @Felix1090_
    @Felix1090_ Місяць тому

    Großartig! Bitte mehr! 🤞

  • @VisualartStudio04
    @VisualartStudio04 Місяць тому

    Great

  • @alefareh5624
    @alefareh5624 Місяць тому

    have so much gratitude to you for this playlist! Thx fron Buenos Aires

  • @beomsukim4568
    @beomsukim4568 Місяць тому

    I've looked at a number of wind analyses using Ladybug, and it's difficult to follow them step by step from the beginning because they all show only the details without showing the overall flow. I'd like you to show me the overall composition of the grashopper or upload a file. I don't know how the beginning part was structured.

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      This video is part of a series: You might want to follow the playlist ua-cam.com/play/PL4Rc2GtLpcNWBnE9B_tj36rtQDVFuPzUu.html

    • @beomsukim4568
      @beomsukim4568 Місяць тому

      @@PhilippGalvanDesign Thanks for the instruction!

  • @abdoudoula2472
    @abdoudoula2472 Місяць тому

    why i have this problem when i turn one the simulation .... can you help me please i'm using lady bag 1.5 and i have a kaspersky antivirus either i switch for ladybug 1.8 and th promlem stille existing .....any one can help me please UTCI MAP show me the ffolowing message errore 1. Solution exception:The recipe failed to run with the following summary: Scheduled 43 tasks of which: * 33 ran successfully: - 1 ComputeSphericalViewFactors(…) - 1 CopyGridInfo(…) - 1 CopyRedistInfo(…) - 1 CopyResultInfo(…) - 1 CreateDirectSky(…) … * 1 failed: - 1 RunEnergySimulation(…) * 9 were left pending, among these: * 9 had failed dependencies: - 1 LetUtciComfortMapFly(…) - 1 RestructureConditionIntensityResults(…) - 1 RestructureConditionResults(…) - 1 RestructureCspResults(…) - 1 RestructureHspResults(…) … This progress looks :( because there were failed tasks Use the report_out attribute of recipe settings to see a full report.

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      @@abdoudoula2472 Which Openstudio and radiance version did you install?

    • @abdoudoula2472
      @abdoudoula2472 Місяць тому

      @@PhilippGalvanDesign open studion 3.8.0 and radiance 5.4 .... thinks for responding me

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      @@abdoudoula2472 First you need to install the right 3rd party versions for 1.8. Also I would make sure 1.5 is completely uninstalled before installing Ladybug 1.8. Then instead of installing open studio. Uninstall and install the open studio app. Which includes the right version of open studio and Energy Plus. Follow this guide and links for the right versions: github.com/ladybug-tools/lbt-grasshopper/wiki/1.4-Compatibility-Matrix

    • @abdoudoula2472
      @abdoudoula2472 Місяць тому

      @@PhilippGalvanDesign what do you meen by the right 3rd party version for 1.8 .... the 3rd party of what now i'm using rhino 7.37.24107 and if i follow the guid in the link i'dont matche betwin ladybug 1.8 and rhino 7 because ladybug 1.8 need rhino 8.4 ..... what should i do bro

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      @@abdoudoula2472 Openstudio, and radiance are 3rd party software which you need for These tutorials.

  • @galjvdjy
    @galjvdjy Місяць тому

    I gave up on this and turned into design builder.just can not do trombe wall simulation always turn into error

  • @hemanisingh1309
    @hemanisingh1309 Місяць тому

    Hi Philip , Thank you for the tutorial. I have a query, m not able to fine the epw file folder in my pc so that I can put the location for the folder in grasshopper . What should I do ?

    • @hemanisingh1309
      @hemanisingh1309 Місяць тому

      Now that I figure out , I made a new folder to save my epw file :) but import epw showing an error - index out of range :2 , I don’t know what does it mean .

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      Ok you don't need to download the weather data. You can just place the URL of the weather data in a panel. Ladybug will do the rest for you... Now if you got an error on your weather data then it might be corrupt. Some weather data files are empty I realized. If the size is very small it might be empty. Have you tried a different one?

    • @hemanisingh1309
      @hemanisingh1309 Місяць тому

      Dear Philipp, Thank you for your response. I re-watched the tutorial carefully and managed to input everything correctly. However, I am unable to see the desired results because the software freezes every time I connect my surfaces via brep. I also realized that the Radiance file is missing. I am currently trying to install Radiance, as I am doing thermal comfort analysis using materials as well. If I encounter further problems, I will ask for help. If you have any suggestions, please let me know. Thank you.

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      Make sure you install the right versions github.com/ladybug-tools/lbt-grasshopper/wiki/1.4-Compatibility-Matrix

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      Further be sure your file units are in meter not millimeter. Often a reason why things freeze.

  • @AdamjoseMourinho
    @AdamjoseMourinho Місяць тому

    Thank you, that's a very good explanations, better than our university lecturer

  • @fatimas9790
    @fatimas9790 Місяць тому

    Thanks so much philip! I have a question, I made a model for bifacial solar module by using HB faces. I added a modifier for the ground ti observe how the incident radiation in the back side changes, but I noticed for values from 0.1 to 0.7 reflectance of ground am getting same radiation values but for values 0.8 and 0.9 it jumps to 10 times higher what could be the reason?

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      Not sure really. Hard to know without looking at the script or model. I would probably test more. And different settings, makeing sure no other settings have changed.

  • @jingzhitay6736
    @jingzhitay6736 Місяць тому

    Great stuff.. trained w rh/gh for over a decade and never ventured into subD.. I sense a calling 😮

  • @mellowjunction
    @mellowjunction Місяць тому

    Such an engaging video!!

  • @4d_sculpture
    @4d_sculpture Місяць тому

    This is amazing, bro

  • @mohanedebraheemsaeed7986
    @mohanedebraheemsaeed7986 Місяць тому

    hi Philipp the butterfly shows me it is old in grasshopper also I download the latest version what can I do

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      There is only one version from 2018. Sadly the developers haven't updated this software.

    • @mohanedebraheemsaeed7986
      @mohanedebraheemsaeed7986 Місяць тому

      @@PhilippGalvanDesign but can i use it or no?

    • @PhilippGalvanDesign
      @PhilippGalvanDesign Місяць тому

      Yes you should be able to use it still. I use it together with Rhino7. I haven't tried it with Rhino8. But I don't think it's an issue.

  • @bahadorziaeemehr6877
    @bahadorziaeemehr6877 2 місяці тому

    Philipp, you are my hero!

  • @henrycowdery2688
    @henrycowdery2688 2 місяці тому

    Thanks for this tutorial, it's great. Can you share what your display settings were for "rendered" mode? it looks nice and clean.

    • @PhilippGalvanDesign
      @PhilippGalvanDesign 2 місяці тому

      I played with the environment to allow for both sun and skylight. Which gives a more realistic look. The menu is slightly different now. In the viewport settings I used scene lighting not ambient occlusion and I turned on edge lines for surfaces etc... thats all. That's all.

    • @PhilippGalvanDesign
      @PhilippGalvanDesign 2 місяці тому

      I probably should do an update on this....;)

  • @LidiaBalan-nf6tm
    @LidiaBalan-nf6tm 2 місяці тому

    Hi! Is it possible to download this code somewhere or purchase it for a university project? I'm getting an error and can't find a solution to fix it. Thank you!

    • @PhilippGalvanDesign
      @PhilippGalvanDesign 2 місяці тому

      Which portion gets an error..? What does the error say?

    • @LidiaBalan-nf6tm
      @LidiaBalan-nf6tm 2 місяці тому

      Could I send you an email with photos of what I haven't managed to understand, as well as some other questions about my project? Briefly about my project, I have tried to analyze an area of the city of Vienna using your tutorials and then introduce my shading construction as a solution for uncomfortable temperatures to test its effectiveness. Of course, if you have the time and would be willing to help with a few tips.

  • @visualrhythm9101
    @visualrhythm9101 2 місяці тому

    I spent 24hrs figuring out how to make it work, in the end dont download the latest version, and download the blueCFD-Core 2017-2 😭

    • @PhilippGalvanDesign
      @PhilippGalvanDesign 2 місяці тому

      well its all explained in the video.

    • @visualrhythm9101
      @visualrhythm9101 2 місяці тому

      @@PhilippGalvanDesign skimmed through because rushing for an assignment i missed out on that key info

    • @PhilippGalvanDesign
      @PhilippGalvanDesign 2 місяці тому

      @@visualrhythm9101 Understand. : 😄 good luck with the assignment.

  • @maxdriftmier6786
    @maxdriftmier6786 2 місяці тому

    Hello, thanks for all the great videos! I went back to this one to try and understand the LB Import Stat node. When I plug the LB Download Weather "stat_file" output into the LB Import Stat node, it turns red with the error "1. Solution exception:invalid literal for float(): N_A" Do you know the reason for this?

    • @PhilippGalvanDesign
      @PhilippGalvanDesign 2 місяці тому

      Have you provided a weather data URL? If you did then you can check the following. LB automatically downloads the file and stores it in a folder. Find the folder on your C: Drive Probably under you user account and Ladybug... You should see several files including a stat file. Note: not every epw file has a stat file. If it's not there then you need to find another source.