Відео

Do you know what brand and model theae are? My wife has a limited x with that side cladding and these are what she needs ( 5'1").

Wow you solved it!

hey man. i just watched your video from about two years ago of you installing rear rotors and pads on a 10th accord. basically i also have a 10th gen accord and i replaced all of my rotors and pads but i am having a problem with both rears. i think it has something to do with the electronic parking brake but i am not sure. is there any way i could get in contact with you and ask you a few questions to see if u could help me fix this? let me know man. thanks!

Wow that’s so interesting! I subscribed and I always watch in full

Can you please show where the VVT solenoid is on this exact vehicle? Thank you.

Bro thank so much

Bro you just save me $1200. Thanks!.

I have a 2004 Rx8 and this method don't work for me. You would need to take out the 3 screw on the Intake like in the video (2)10mm nut near the Oil filter. Also take out the air filter with 4 screw of the Throttle and if you want easy access and work better because have big hand/arms take out the alternator. This method on this video is for engine with 6 ports which the intake is different of 4 port

Can you please tell me what size exactly is the 2 starter mounting bolts

Nice installation with explanations! 👍

Most in depth mechanic video ever in general. Really appreciate the thoroughness!

I like that you did this during the day with plenty of light, so your audience can see everything clearly.

Long time mechanic, just checking on the job. Brother, this is by far the best video I have seen, good job.

I just did this solenoid swap today and tne method that you used to pull out the entire solenoid was the way to go. I initially pushed in the clip on the soneoid so i could then used your method of pushing it out and keeping the clip and the vacuum line connected on the blue clip. I then removed the vacuum line. complete access to white clip solenoid and repeated again. Thank you for the hand gesture to indicate pushing out.

where is part 2?

The video left out the actual removal of the knock sensor. Was that intentional? Otherwise, great job on the video! I appreciate your attention to detail!

The serpentine belt.wpuld that.make.my turbo sqweek after shutting the engine off and while.driving it

Mechanicing is fun!

ty!!!!

Ok was it making a high pitch squelching sound about 5 minutes after you start it ?

Have you had to do the tensioner pulley on the 2016 cascada?

I was told the car would have to be lifted in order to replace these?

Honda Prius? Hmmm🤔

It was originally labeled "PB Blaster" and the manufacturer renamed it some time ago to just Blaster. Us old timers still remember PB Blaster and still call it that out of habit. Great vid. Thanks.

What codes was the car showing? I have a low purge valve flow and car feeling like turning off sometimes

So the only o rings required are the ones in the compressor? You don’t need any on the hose end as well?

I’ve found it easier to leave that bolt that holds the hoses to the compressor be. Disconnect them from the accumulator and condenser and remove the compressor from the front with the hoses attached. You can then transfer them to your new compressor.

Thanks subtitles

covers it all and great video, make it seems very easy to replace brakes. Thank you!

Thank you

You can reach the top bolt with some extensions from the top side

Also can you replace just the strut that has the hydraulic lines on it or do both the strut and lines have to be replaced? I see the O ring on my has broken loose on my 2010 srx

Where in FL are you located?

Are all the camshaft sensors the same? Im ordering 4 on amazon in a few days.....

Yeah everybody shows how to fix the lower but they don't show you how to fix it when it comes off to shift through

Subbed and liked. Thanks!

I had this code on my car on saved codes for a while but mechanic kept telling me it didn't come out on his code reader. I got a catalytic converter below threshold code now and this one finally came out to pending code with the cat one. Can the cat code be because of the 0661 code?

Did you post the dryer/receiver replacement?

Scale 1-10 how difficult is this lol

I just wondering if I can adjust the brake pedal little big high?

THANKS SO MUCH FOR SHARING EVEN THE SMALL DETAILS <3

You the first but you are way off topic and subject but thanks for trying

Twisting those brake calipers back in doesn’t damage the actuators?

crappy video. Cant orientate where he's working on the engine

Great video my friend. Thank you for all of the information in the description

Truly appreciate you sharing this. Just replaced mine and everything went flawless. Thank you

How did you know the starter was bad mine would turn on but wouldn't crank

Can you do a water pump on Buick cascada

Thank you!!

Hi mate, thanks for making the vid. I just got 8 mm Allen key but it's slipping and I don't get enough grip. Damm I have a manual jack and already kept it down twice due to mazda's stupidity. Is there any other tool I should consider? Thanks heaps, appreciate your time man