Відео

The mad scientists 💪👌👍

What’s that cost right there!? What about with no rear steer

My dream rig would be something less then 10 yrs old, dependable, and won't cost me a arm and leg to maintain. Very cool build though.

Dream car🇺🇸

Great work Thomas!!

S0 dope

Beautiful work @Fabn801 👏 Videos are getting better every time!

Grind hard gonna have you beat very soon

Very nice. I like this chassis as well.

That dash and floor came out great. Nice build.

Looks good 👍

thats cool

Nice build!

That’s has to be dumbest and most dangerous way I have ever seen a tire change

Another old square body 1 ton donate it's parts for a rad build

Hell yeah on the grind, on point

Love it!

Make sure to keep the small block too, it runs!

First ! 2025

When the cherry picker doesn’t work you want to break the bead off in 1 spot of the rim. Put that square stock right next to the edge of the bead and drive up it with a truck or buggy. Once the bead starts to go in that 1 spot it will go over the entire tire.

What is the advantage of this over say an atlas

Awesome case backed by some cool dudes.

Other than supplying drive train axles and wheels. What does it run to get a roller like this? You have some nice cars

I always use a burke bar I flip it upside down shove the fork side in the bead then I drive up the bar and it pops the bead every time helps if you weld a plate to the handle of it I just welded a flex plate to my burke bar

12’ ish ???

Any idea what a set of 9 inch portals run ?

Steel plate between legs with hole just barely over wheel diameter. Weld ring to edge of hole to push on tire. Lift from center.

Sheesh 🔥🔥

Holy crap

Where the tires glued on?

Lots of ways to split a pea!

Somebody needs to educate that boy on the dangers of Stored Energy.

Weld that piece of box section to the crane between the legs use wd40 not water and buy a slide hammer to brake the bead

Hook a trailer up to a truck and use the jack to push the bead down to break it. Had to do the same thing with another set and it worked surprisingly well.

Bead breaker from harbor fright, for the win.

Dang that was rough, how long have the tires been in wheels??

It is VERY obvious that you've never worked in a tire shop before. This is almost painful to watch. Search "tire hammer" and then buy one. Use that to break the bead and the wheel will come off easily. Or, use a hi lift jack under the bumper of whatever truck is handy, put the base of the jack on the tire as close to the wheel as you can and push the bead off.

This is the most sketch shit I seen today😮

Put a board on the edge of the bead and drive a truck up on it, you might have to reset it a couple of times. This is the farmer way of the old days..

Are the tires junk? If so just take a sawzall to them. 😅

You put the forks from your forklift on the top legs to hold the tire down and safety when it pops

You guys could've used the floor jack sitting there and already had both of those tires broke down off the bead or you could put a piece of square tubing under the cherry picker legs in just in front of the rim and secure it in place so you're not pulling the tire up with the rim. Or you could just make a slide hammer with a 4 foot piece of bar stock a pipe to slide it into and a 4X8 piece of 3/8 steel plate. And you could also just go and buy a cheap manual tire changer at Harbor Freight and bolt it to the floor or a pallet

1 foot backhoe bucket. Use the teeth push down with back hoe. Or stand tire up against a wall or conex and use forklift forks

So as that forklift was driving by you didn't give you any ideas? Lol.

If you wanna quick way to de bead it we just slide the tire up under our jeep bumper and use a high lift jack to break the bead it's super easy

Ive done it several times, just takes a few adjustments of the "ramp" so its almost touching the wheel so it pushed the bead down and doesn't just mash the sidewall like what was happening with your method.lol

Should put a weld on that bar u run across the front so it doesn't slide out

Lay a 2x4 box tube on it close to the wheel and drive the front tire of a diesel truck up the box tube to pop it off the bead

Boys aren't too smart.

Boys aren't too smart.