Відео

Hello Bryce, Can you send photos of your floor to support@epodex.com for further assistance? TEAM EPODEX

Hello Lynn, With our 2K Polyurethane Resin, you must apply it very thinly, in a crisscross motion. This process eliminates lap lines or roller marks. The product is also dilutable with water to avoid an orange peel texture.

Hello, Yes, it does, it's designed for these purposes :) The EPODEX Tile Grout Pen is a special acrylic-based paint for colouring and refreshing tile grout lines. See here: www.epodex.com/en/product/epodex-white-tile-grout-pen/ Team EPODEX

Hello, Yes we offer Microcement for walls: www.epodex.com/en/product/microcement-for-walls-doors-and-furniture/ Make sure your order the correct primer as well: www.epodex.com/en/microcement-individual-products-components/ For further assistance email support@epodex.com. Team EPODEX

Hello, Normally yes, but it also depends what paint was used on the concrete previously? Email us at support@epodex.com :) Team EPODEX

Hello, You can use our Tile Paint directly: www.epodex.com/en/paints/tile-paint/ The gloss level for 1K is satin & for 2K satin matt. Do you mean can you make it more glossy? EPODEX

Hello, You can use our Polyurethane Sealer found here: www.epodex.com/en/product/microcement-for-floors-and-stairs/ EPODEX

Thanks :)

Bună ziua, PU lucios: 10:2 în greutate (de exemplu: 1 kg A + 0,2 kg B); PU mat: 10:1 în greutate (de exemplu: 1 kg A + 0,1 kg B). Sper că vă ajută :) EPODEX

Hello David, Yes our MATT version has the highest scratch resistance :) EPODEX

@@epodex-uk3877 Thanks a lot :)

Hello, Our products are BUBBLE FREE so we do not recommend using a pressure pot nor can we advise what pressure to use as we dont test our products with a pressure pot. Team EPODEX

Hello, To bring your surface to a high gloss, use our sandpaper, which can be found at the following link below: www.epodex.com/en/product/waterproof-sandpaper-230x280mm/ Start with a grit of P100 and gradually sand your way up to a P3,000 grit. To achieve a mirrored effect, you can also sand up to a P10,000 grit. Then simply polish the surface for completion. Polish your surface with EPODEX Polish, which can be found at the following link: www.epodex.com/en/product/polish-polishing-paste-100ml/ Team EPODEX

@@epodex-uk3877 Thanks for your help. What about walls. Can you apply that for vertical surfaces or its only for horizontal ? Thanks

Hello, We recommend stirring for 3 minutes, then transfer the mixture to a clean mixing jug and stir again for another 3 minutes :)

Hello, No its not :) If you decide to sand only use DRY sandpaper. EPODE

Hello, We do not recommend spraying our epoxy resin. What kind of project do you want to do? EPODEX

Our Tile Paint 2K has a satin matt gloss level :)

Hello, We recommend the Pro System. www.epodex.com/en/product/pro-system/ The epoxy resin PRO system is ideal for coating surfaces and making jewellery and small objects. It can be poured up to 2 cm deep per layer. The Resin A-component and hardener B-component are included in each set, as well as the desired colour dye or pigments. Instructions for use can be found on this product page. 24 hours at 20°C to harden and 7 days for full chemical curing to occur. You can use a demoulding spray if needed but epoxy never bonds to silicone moulds :) Team EPODEX

Hello, It wouldnt be easy no :( Removing paint is never easy. We offer the 1K acrylic based paint and the 2K epoxy resin based paint. The 1K would be easier but still a hard and messy job. EPODEX

Hi :) Our products are chemical products but once cured and hardened they are not toxic and do not pose a threat to one’s health. Our products are remarkably odourless during processing, but we always recommend wearing a mask, protective clothing, and gloves (nitrile). Goggles can also be to protect one’s eyes. When sanding and griding surfaces please wear a respirator mask to avoid inhaling dust. Always work in a ventilated room meaning that the doors to the room are open to provide adequate air flow but do not open the windows as humidity can affect your work. Team EPODEX UK

Hello Jasmine, This is called a Dirty Pour Technique. Heres how it done: If you wish to create a dirty pour you must first create a barrier (dam) around the edges with our strong, durable masking tape. Press the tape around the entire project. The tape should stick up at least a half-inch. 🎨 Pro Tip: One continuous piece of tape may be difficult to achieve but aim for as few seams as possible. Don’t wait too long before removing the tape. If the resin completely hardens, it will be difficult to remove. For the least hassle, it is best to remove the tape no more than 16 to 12 hours after pouring. Gelling times can be found on our system comparison sheet. You want the resin to be set, but still flexible so that the tape pulls off easily allowing the epoxy to flow down the edges in a slow movement. Upon removing the tape, you will notice some spots that will need to be treated with a paintbrush to ensure full coverage. Make sure you dip the paintbrush in the epoxy mixture before using it. Start using the paintbrush in a horizontal motion, spreading the epoxy over the edges. Do not worry about messing your design up if you have worked with various colours as the epoxy will still flow downwards bringing the design you have created over the edges. Only work on the face of the edges, not the top. Once you have painted the edges with a paintbrush take a stir stick and run it along the bottom of the edges to scrape the bottom drips off. You will need to do this periodically for an hour or two. For a final topcoat of epoxy, you can sand at a higher grit as the epoxy layer will then remove the scratches from sanding. You can round sand the bottom edges as well if needed to give the finishing touches to your edges. Hope this helps :) Contact me for more assistance at support@epodex.com. Team EPODEX

Hi Gordon, Ofcourse :) Do you have the moulds already? How thick do you wish to pour the epoxy resin? Team EPODEX

Hello, We recommend our Tile Paint 2K: www.epodex.com/en/product/tile-paint-2k-all-colours/ It is an epoxy resin based paint :) Contact us via email at support@epodex.com for direct assistance and design tips and tricks.

Thanks

Hello, We are only selling epoxy resin in the USA at this time but will expand our product range soon :) Team EPODEX

Hello, The rose or any real flower must be 100% dry before it can be casted into epoxy resin :) TEAM EPODEX

Hello, Thanks for your interest! Do you want to coat a surface with colour or without? TEAM EPODEX

Hello, Thanks for your interest! What are the measurements of your project? Length, Width, and Depth? I can see what we can offer you :) TEAM EPODEX

@@epodex-uk3877 Hmmm… I’d say no larger than 1 1/2 (one and a half) inches, length and width. Probably pretty thin, but thick enough to fit a small cut piece of paper, maybe an inch or so depth. Small but big enough to use for a charm to wear on a necklace or something similar? Would that work?

Hi Darren, Thanks for your interest! Yes the epoxy resins we offer are all self-levelling, bubble free, and crystal clear. According to our epoxy resin calculator found here: www.epodex.com/en/media/epoxy-resin-calculator/ You need 15.40 KG. For layers of 2 cm in depth you can use our Pro System. www.epodex.com/en/product/pro-system/ Hope this helps :) TEAM EPODEX

Hello, Thank you for contacting us :) The image needs to be primed as paper is porous but how to prime depends on the paper used. Contact us via email at support@epodex.com for further assistance. Team EPODEX

Hello, Which system are you referring too? What kind of project do you want to do? Team EPODEX

@@epodex-uk3877 2k time paints

@@epodex-uk3877 another question. Someone mentioned that they had different colour when dried as while painting they were putting more paint from mixing cup to tray seemed like paint already darkened?

Hi Tom, Thank you for your interest in our products. We recommend the Tile Paint 2K. www.epodex.com/en/product/tile-paint-2k-all-colours/ EPODEX TILE PAINT 2K has a satin finish and is abrasion resistant. This 2-component paint is ideal for painting tiles subject to heavy wear and tear on floors, walls, and ceilings. In addition, this paint is specially designed for tiles that are in constant contact with water (e.g., in a shower). It is the perfect solution to modernise your tiles in a durable way. Consumption Volumes: 120-150g/m². The quantities listed on our website are for one coat so double up to cover your sqm for two coats which are recommended. Depending on the texture of the tiles, use 80 grit for high-gloss tiles and 150 grit for matt tiles before you apply the product. Then use our Pre-cleaner found in your equipment tab. We do not recommend using a primer as we cannot guarantee the adhesion with our product. Detailed instructions for use can be found at the link above. Once fully cured the tiles are waterproof and chemically resistant :) TEAM EPODEX

Hi Paul, Thank you for your interest in our products. Rough sandpaper for example P400 can be used. www.epodex.com/en/product/waterproof-sandpaper-230x280mm/ TEAM EPODEX

Hello Paul, we recommend to apply 1-2 coats depending on the substrate and the desired colour. A top coat isn't necessery.

Hello Paul, at 20°C the tile paint 2k has a pot life of 50min.

Hello Paul, we recommend using masking tape to cover the edge. You can either use a paint brush or a small roller to paint the edge.

Hello Miha, Thank you for contacting us. The mixing ratio is 2:1 so based on the information you have provided the ratio you should have used is 113ml to 56.5 ml however you used 113ml to 56ml. If the ratio is off the epoxy wont harden. The epoxy is extremely sensitive and if the chemical reaction between the resin and hardener doesn´t occur it wont cure. Can you send us an email to support@epodex.com for further assistance? Team EPODEX

@@epodex-uk3877 0.5 ml over 56 ml that's less than 1% error. What margin error do You allow for this product when mixing?

​@@epodex-uk3877 isn't it mixed by weight and not by volume? How does the humidity in thr ait affect the hardening process?

Hi Jimmy, Thank you for your interest in our products. We recommend pouring a thin layer at the base of your mold. Then place the flower inside allowing the stem to sit in the poured epoxy and wait until the layer becomes gel like. This way when you keep pouring over it wont float or move around. Your EPODEX Team

Hi there, yes any silicone mold can be used!

Hello, Thank you for contacting us :) The EPODEX Separatng Agent Spray is ideal for casting applications with epoxy, polyurethane, acrylic and polyester resins. Ideal for applying to smooth GRP and silicone moulds and in combination with the EPODEX Separating Tape. Excellent separating and sliding effect. Thanks to the fine spray mist even angled areas can be reached. Team EPODEX

Hello, Thank you for contacting us. The scale is required to weight out each component so that you can precisely adhere to the mixing ratio of 2:1 (2kgA:1kgB). For layers of up to 10 cm you should have purchased the Pro MAX System. The Resin A-component will say Pro Resin but the Hardener B-component will say Pro MAX. Is this the system you are using? Mixing Instructions: Mix the resin A-component with the hardener B-component in a ratio of 2:1 (e.g. 2kg resin: 1kg hardener). Stir through the edge and bottom of the mixing cup as material will settle there. Ideally, pour into a clean mixing cup and mix again until the mixture is streak-free. This ensures that the resin A-component and hardener B-component are completely mixed together. Pour the resin-hardener mixture onto the surface to be coated immediately after mixing, as the product can start to boil in the mixing cup. Let us know if we can be of any moe assistance :) TEAM EPODEX

Hi there! Yes the resin can overheat which would lead to cracks, bubbles and yellowing. For deeper castings, we recommend using our even less reactive epoxy PRO MAX. www.epodex.com/en/product/pro-max-system-resinhardener/

@@epodex-uk3877 thanks. Would I still get the crystal clear effect? I want to create a coffee table sized slab of resin with a flower arrangement inside it.

@@kierand9410 Yes our PRO Serie is crystal-clear

Hi Denisa, Thank you for contacting us. The max. material shrinkage after processing is 1%. Cracking can occur from when the wood used is not properly primed and therefore sealed off. The table shouldn´t break if you properly apply the epoxy and allow it to fully chemically cure. Make sure to also apply the necessary legs and bars underneath the table to prevent it from warping as well :) Team EPODEX