Відео

where can you get the interface board?

price ?

Hi, I have an error in Hosonsoft that says "x motor position error (grating position and pulse position error are too large" This happens after about 2 hours of printing and after a knocking noise. Any ideas

Their on screen interface needs a lot of work. After hitting ok it just stays on the same screen. There is no confirmation that calibration is complete. Kinda like this video cuts off too. Struggling yo calibrate my machine and I can’t help but wonder if the calibration simply hasnt took.

After installing the riser base, how the hell am I supposed to use the laser now? It won't measure the distance, because everything that I want to cut/engrave is sitting too low.

How is this different from silhouette

Can you make rhinestone heat transfers with this

The ipaddress you verbally say is not the ip address on the screen. Really messed us up!

Cameo 4

Useless

The riser you sent me does not have the ability to screw the base on the bottom. Please update the video! (there are no screw plates as shown on it's bottom). This one does net even have the passthrough panels.

Good

Does this procedure also work with LightBurn? Thanks

I've just purchased a licence key from you but when I go activate it's just coming up with could not connect

I need one ASAP too, and xtool is impossible to deal with.

You did a wonderful job!! Thank you so much!

How the heck does the software know/tell what screws are where??? This sounds so dumb

Hello, can you please tell me the possible reason my camera isn’t working after I upgraded the software?

찾던 영상! 도움이 되었습니다 감사합니다!💝

How much does it cost?. If it is different price ranges, please give examples thank you thanks for the video

Hi we have this exact model and still on a learning curve - the first rounds of prints have been great but we are now finding minor scratches on the prints - any advice? Looks like it happens when the prints go through the dryer perhaps?

What version of software is this using? I do not have a burn mark at level 1 and no buttons to move closer to the first mirrors. I am not using the V2 Beta software since none of the tutorials I've found show this software

i am trying to find a video that show exactly where to put thr Strip seal

My machine has quit exiting the air. I’m gonna try and clean it.

I tried to watch this through the link in the app, but the ridiculous klaxon sound was going off throughout. Quitting the app, or going back to stop it closed the link to the help guide and video. 😖

head doesn't stay in. brand new. junk trash.

I keep getting an error calibrate again when I click updating calibration. No customer support to help.

Hello how did you put the Lazer down

Hello! We are having an ink out error but we tried this method with no luck. We pressed the ink button to unlock the carriage and then when we press the button again it doesn’t do anything. Our main printer blew a board and have been waiting for it to arrive so we we’ve been working tirelessly for days trying to figure it out. We are drowning financially and really desperate to get it working. We were thinking maybe a firmware issue or maybe something with the ink volume control board thing..our other printer doesn’t have one of those so we aren’t familiar with it and can’t find any material on its usage. It has a little blue button on it and we aren’t sure what it’s intended for or how to properly use it. We have regular dampers with no chips… if you could please help us we are desperate. We would be forever grateful

Where do you find that software. All I can find is XCS on their page.

This does not work. Mine never says it's ready!

What OS are you using

could this be used with UV prints?

Has anyone fixed the optical sensor? This thing is an aggravation. It's supposed to free you up to do other things but I have to stand and babysit it or it will reel the film and a pile of DTF glue right into the oven. I have cleaned the sensor with sensor cleaner and antistatic. It works great for less than three pages then it's off to better off doing it manually land. If anyone has the actual fix I would be eternally grateful!!! Right now this thing is just a POS in my shop, not earning it's keep. 🤬 ~Please forgive my cross post.

This is exactly what i needed to see, thank you for the clarification.

Bonjour, cela fait des mois que j'essaye de mettre la caméra à niveau mais rien ne j'ai fait appelle au service technique du site et rien, pouvez-vous m'aider quand j'appuis sur process j'ai une fenêtre qui indique exception:illegal input!

this is a very silly video. I come here looking for assembly instructions and you start the video in the middle of the assembly?

"perfect spray pattern every time" hahahaha

do you have to wait for the printer to tell you when to replace? it currently just says near end of life

This is amazing!!!!

Hello, this is very helpful but the water pump is not is amazon or eBay, any place where can i buy it? I need one sap

A DVD SHOULD HAVE CAME WHITH THIS DON'T WAST YOUR TIME OR MONEY

This is a Wast of money I have this Printer All kind of problems I will be getting my money back Whoever Reading this don't wish your money

Pretty useless not seeing it WORKING. Was going to buy; but I hear ot does not cut well off a roll. Goes out of alignment.

How I buy this product ? Please help

It is very inconsiderate to upload 200 videos at one time. I am on my phone, looking at my subscriptions and I have to scroll for days to get past your videos. I am immediately unsubscribing.

Bonjour, Comment régler vous le focal je n'arrive pas à utiliser lightburn avec ma p2 .

Where can I find those clips to hold the hat in place ?

When you litter my feed with endless videos, I hit unsubscribe.

I’m having issues when I’ve cut the media and it feeds into the powder at the end it folds in on itself and then when it comes out of heater the last ones don’t cure enough and get stuck to the previous ones