![Mack Of All Trades](/img/default-banner.jpg)
- 10
- 357 671
Mack Of All Trades
Приєднався 12 вер 2020
Michael Mack has two art degrees and a ton of construction experience. What good is knowledge if you don't share it?
How To Install A Towel Bar In Tile
How to install a towel bar in tile. By Mack Of All Trades.
Переглядів: 20 830
Відео
How To Hang Shutters On A Brick Wall
Переглядів 56 тис.3 роки тому
How to hang shutters on a brick wall by Mack Of All Trades
How To Repair Wood Rot
Переглядів 25 тис.3 роки тому
How to repair wood rot. This repair was done on the side of a shed. By Mack Of All Trades.
How To Match Ceiling Texture
Переглядів 17 тис.3 роки тому
How to match ceiling texture after a ceiling repair or patch. By Mack Of All Trades.
How To Resurface A Work Table
Переглядів 1083 роки тому
How to resurface a work table. By Mack Of All Trades.
How To Freshen Up Your Tub Shower Caulk
Переглядів 4423 роки тому
How To video about renewing a moldy caulk line in your tub/shower by Mack Of All Trades
How To Improve Your Fence
Переглядів 4193 роки тому
How to improve the look of your fence from the inside. By Mack Of All Trades.
How To Retile A Shower, Add A Niche And A New Valve
Переглядів 1,1 тис.3 роки тому
How To Video showing a complete tub surround remodel including tile with a new niche and shower/tub valve replacement. By Mack Of All Trades
How To Repair Rotten Fascia and Soffit
Переглядів 237 тис.3 роки тому
How to repair rotten fascia and soffit. By Mack Of All Trades
How To Remove A Toilet
Переглядів 1603 роки тому
How to remove a toilet to either replace or upgrade tile and replace original toilet.
this is going to be rotted out in one year....
Doing my research , z flashing could be considered. This guy knows more than me. He helped me decide to just buy 1 sheet pressure treated plywood and only cut out the rotting spots. I’ll be using z flashing I think. I’m also struggling to figure out if u should flash explosed wood trim. The wood trim capping my existing plywood exterior is generally rotted on the top side. I could just caulk after cleaning and repairing though
It's not his repair ability but his sense of humor which is harder to establish being a multi home owner😊
I agree with how you do this, but I added a dab of adhesive to the hole. A dab will do ya, and if you ever want to remove, just drill it out
thank you. good video :)
Strong work. At ~16:00 when you lay out your tile, how thick are your wedges - what gap do you want btw the bottom tile and the tub? Also, your tub was level but if the DIY audience notices that their tub is not level, they would need to account for that. Also, the DIYer might tile from the inset to tub instead of tiling up, as trimming the base of the tile is easy and not noticeable. Also, at 17:20, what dimension did you miss by 1/4"? Have you buried cardboard behind a shower in the past? No, it shouldn't ever see moisture, but... Why run the cement board vertically? I feel that would allow the board to shift and crack, whereas horizontal pieces would not. The dimensions are usually 5ft long, to match the length of your enclosure.
Good man.
how do you cut so straight?
Great job
Precise and exactly what I needed to know thank you
I love that the Jenga joke was so good you had to film it instead of just doing a VO hahahaha
One of my favorite products for iffy wood is Minwax Wood hardener. It's a liquid you brush or pour on that soaks into porous wood instanttly but hardens as resin is dissolved in it. Fairly water proof too since it's resin but will harden even particle board like a rock if you use enough. Adams Rock hard putty is another fave.
what a fun lesson! thank you Mack :)
No need for primer?
Awesome video. So easy. 😂
Excellent video, fun to watch. Great tip to use longer screw to find good wood. I’ve subscribed!!
"I'm also really good jenga" 😂😂
top work!
about to replace a 2ft end piece of the facia... needed this 'how to'... thanks 👍
Thank you for explaining
The imaginary line measure😂😂😂... FNG
Come back mack we need you
Very good bro, and very entertaining.
Im attempting to fix a friends situation that is very similar to this. Thank you so much for the video.
Ok now can u come to my house and help me. I have a lot to repair 😂
Loved the video, I shudder to think of the mess I would have made in my own.
This is the worst way to install vinyl shutters. The PVC pins break from the suns UV. Very poor design. This will become a high matintenace issue over the years of home ownership.👎🏻
Great advice on not having to use concrete anchors. This looks like it will be a much easier job what I had imagined also appreciated the advice to go into brick, and not the mortar, especially since they had recommended going into the mortor and not the brick.
He is doing very well, he is repairing, explaining details, very good.
I scoured the earth to find a video clearly explaining what a fascia and soffite were. I loved your explanation at 2:35. Epic!
Great video😂❤
Your fantastic shutter jokes got me hooked, you have a new subscriber! Thanks for the laughs and the help on my shutter project.
what thickness wood is this
Looks good, why not use treated wood where possible?
I am not surprised that the dude has two art degrees. I am sure if the art jobs paid more, he would not be doing this sh**t.
Love it. No B.S. makes this a straight forward repair. He not telling you that you have to rebuild the whole frickin house.
In 15 years, my son will you how to fix it again, this time addressing the flashing errors that delivered the water into the soffit!
About the triangle shape how you cut it?
Thanks Brody, just wanted to know if the tile would crack and therefore would need to follow a special process. I enjoyed the tutorial, greetings from Mex.
All my soffit hangers are termite eaten I saw them from the inside when I rebuilt a door rough opening. So all the material has to come down and be replaced along with splicing some termite eaten rafter tails.
Should have put a piece of flashing behind the downspout But otherwise looks good.
No z flashing?
Best Video on YouTUBE!! Dude, you are funny!! Thanks so much!!!
I'm here because I started a paint job that has now become a rip and repair job. The honey do list exponentially expands on its own!
ain't that the truth... 🍺
Very good job
Before you call them “shutters,” ask yourself whether they can be used to “shut” the windows. These are not shutters, just imitations thereof.
Thank you! This really helps.
You're a great teacher, thank you!
You’re funny! hahahaha
Dude! You’re funny! Thanks for the helpful video! 🙌