- 1
- 3 674
JazzyProjectz
Приєднався 1 бер 2024
MAZDA CX5 2.2 SKYACTIV - ENGINE REBUILD
Mazda CX5 2016, Sport Nav, 2.2D Skyactiv, AWD - Engine Rebuild
Parts bought and work done:
• Cylinder head rebuild
• Head skimmed and washed
• Rocker arm lifters refurbished and tested
• Valves cleaned and re-lapped
• New valve stem oil seals
• New cylinder head bolts
• New exhaust cam shaft
• New rocker arms
• Crankshaft and conrod bearings inspected. No excessive play or wear found.
• Turbo inspected, no play in turbine shafts.
• Injectors ultrasonic cleaned
• De-carboned cylinder head, intake manifold and EGR system.
• DPF inspected, no issues found.
• Water pump inspected, no issues found
• New timing chain and oil chain kit installed.
• New flywheel install
• New clutch kit installed
• New gasket kit installed
• New thermostat
• New coolant temp sensor
• New MAP sensor
• New exhaust gas pressure sensor
• New oil strainer
• New oil filter
• New fuel filter
Parts bought and work done:
• Cylinder head rebuild
• Head skimmed and washed
• Rocker arm lifters refurbished and tested
• Valves cleaned and re-lapped
• New valve stem oil seals
• New cylinder head bolts
• New exhaust cam shaft
• New rocker arms
• Crankshaft and conrod bearings inspected. No excessive play or wear found.
• Turbo inspected, no play in turbine shafts.
• Injectors ultrasonic cleaned
• De-carboned cylinder head, intake manifold and EGR system.
• DPF inspected, no issues found.
• Water pump inspected, no issues found
• New timing chain and oil chain kit installed.
• New flywheel install
• New clutch kit installed
• New gasket kit installed
• New thermostat
• New coolant temp sensor
• New MAP sensor
• New exhaust gas pressure sensor
• New oil strainer
• New oil filter
• New fuel filter
Переглядів: 3 716
Hi my friend. Hope you can help me. I must change the connecting rod bearings on my cx-5 diesel. I have ordered the bearings from ebay, but they keep sending me bearings with the lock notch on the right, instead of the left, like what's on your vehicle Do you know where I could get the bearings with the locking notch on the left?
I got mine from Ebay too. Link of my supplier is below. The part number you need is SHY111SEO. www.ebay.co.uk/itm/156002979283?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=A1fDF8X5Rhu&sssrc=4429486&ssuid=Pg-Y2FF6QT2&var=&widget_ver=artemis&media=COPY
@@JazzyProjectz Thanks very much
Excellent join!
Hi, congratulations. Excellent job. Could you tell me how much the investment was in spare parts and how many hours of work it took to finish this project? Thank you 👍
Project cost about £1500 in parts and about 10-12 days, Evenings and weekends.
Hi. What was the cost of materials to do the job. What made you decide to do it? Camshaft failure?
Was about £1500 in parts. The car had a blow head gasket. So by doing a thorough rebuild like this I'd like to think the car should do another 70,000 miles without any engine troubles. £1500 for another 70,000 miles is a good return for me.
How do you take ecu off
I used a bolt extractor kit like the one in the link below. www.ebay.co.uk/itm/115792899049?itmmeta=01J28TGH2N2EYGP14CCMC07CVE&hash=item1af5cb6be9:g:3oAAAOSwIIxiBTRk&itmprp=enc%3AAQAJAAAAwHa41648EWlOZBqgGR2LtOuM0%2BT5tBZsWchLnHJHZDNQyNaWSQhRWAeis9uGSbekMnYmOPsoeyeLbQleciygQCIK6fbMvPPvtpyqaZd1FaehVN2tNjVaBcVmhrjovl1HXtzkzDLZvpkgYs%2BtD2e0nt2OdCCMLoX5qD0KOF5TrKmE65Wlnoxd2Vtlrp11V5BEJDPdOyn3WjTge%2BUvouEGizvvrQNbbF3wq6ZixWiXX8vnJeJQdmWfLQJNVxwujML5QA%3D%3D%7Ctkp%3ABk9SR7SRwpqSZA
@@JazzyProjectz thanks
Great video
Jazz where you based
Hanwell, West London,
@@JazzyProjectz do you have a contact number
Excellent video, appreciate the time taken to make such a thorough video. I may have missed a part there and if I may ask. The conrod cap bolt, did you reuse the original bolts, if so what was the torque procedure/setting to nip them up? Many thanks
Conrod caps 1) 29 +or- 3Nm 2)90 +or- 10 degrees Cap bolt do stretch over time but can be reused. Maximum bolt length = 45mm. If your bolts are longer, get new ones.
How many kilometers on the original engine?
137k
Done the same but without taking the block out of the body... all on my driveway. I did two huge mistakes: 1. Did not clean up the Exhaust Pressure Pipe going to the sensor, even though I replaced the sensor with the upgraded one. Big headache followed 😁!!! 2. Did not change the clutch and seems like it was necessary to do so! I have the same engine 2016 CX-5 with 140k miles, pretty descent car once fixed! Still beating my head off because didn't change the clutch back then! 😆 My total cost of parts was nearly £1000... Little advice which I needed and couldn't find nowhere - to clean the Exhaust Pressure Pipe once on the engine and you don't want to take DPF and Turbo apart = use hand break cable on a drill... the only wire that helped me to unblock the fully blocked pipe! Hopefully this comment can help someone in need! Good job!
Great tip with the handbrake cable. will keep that in mind for next time
How much did this project cost please. I have a cx5 with no compression, and don't trust local mechanics. Also what area are you based in
This project cost about £1500 in parts. I'm based in Ealing
Those copper wasters are no good and will eventually cause a carbon death , you should pull the injectors and use part SHO 1-13-H51 which are silver in colour
you're right. I'm going to swap them out. thanks
Hellow please advice where did you get your parts from, thanks
Most parts get from Ebay. Also get some parts from Japan. Website. www.amayama.com
let mi ask coz am in uganda and i happen to have aproblem with oil dillution i happen to have a dpf delete after i found out that the dpf material was stolen then i unpluged the sockets for the two sensors and my ecu was given aremap and dpf was deleted but one of the mechanics used the can at one point and plugged back the sensors was my mistake not to seal of how ever after some month down the road the oil dillution started again i dnt knw if it has anything to do with the dpf sensors active again and now the valve are high and the ecu tries to do aregeneartion again any advice wd be of help any any one can try and find mi asolution
Sounds like this car has been hacked to bits. I don't really have any advice for you, sorry.
Great job! Keep it up Jaz ;)