Відео

Thats got to be the best earth clamp I've seen on a small machine

Hi pal 3 years on any issues? Have you run 6010 on it? I'm seriously considering this as my next buy

great video. have you still got the welder? if so how has it held up the past couple years

How well does it run 3/32 7018 and 6010 on 115v 20amp breakers ….. mostly what I would need it for the most .

How low will this go down in amps? Thanks

Did you get the tig lead with it or have to pay separately? And where did you get it all from? Cheers.

High frequency refers to the start on tig which doesn't require contact between the the tungsten and the workpiece, IE. A button or a pedal to initiate the arc rather than lift/scratch start. HF has nothing to do with MMA welding. A decent looking machine for site work. Cheers 👍

Can this machine run 6010

Hi , on my fuse box I got information about fuses.and my garage got B16 NHXB16 MCB.. If I buy this machine can I use I’mn my garage? Thanks

Top video. Loving the contents. Always coffee first.

Hello Sir, is the machine accept 220V AC from mains? And what current it shoots? Is still AC or DC only or both? And can we change polarity on this machine? Thank you 🙏

Hi! Never roll the ground cable like that. It creates induction circle..

Would like to see you do a reviews on the Warrior 250 & Warrior 170 single phase mig welders.(reviews are hard to find).Been looking at Warrior,but Oxford Migmaker is tempting.

Had a 250amp from Phil for ages now, still going strong, much better than those inferior millers, esabs etc :)

Any problems with the torch trigger ?? My one been strange from new .. When you welding and then take finger off the trigger it still pumps out the wire live ! till you pull the trigger again , even then it still comes out live .. ?? only used if on few jobs .. Didnt know if theres a trigger mode i dont know about or its just faulty from new ?

How easy is it to feed the wire? Thanks

Made in china?

Weres part 1? And can u plz weld sum 10mm Plate or sumthing simler id like see how the it welds cheers

I agree always coffee first ha

Thanks for the video been thinking of investing in a warrior welder to start doing some small metal working and fabrication work from home in my spare time as I work as a welder in a company at the moment

thats big amps for single phase.It looks very portable and easy to move about i like that about it. do some videos of it welding soon please.. do the airline fittings work well for the gas? no leaks at all?

good job..hope the welder goes good for you..

You can get ND (neutral density) filters to put on your camera lens, so you can film the weld puddles. They don’t cost too much either. Great stuff though, Thank you👍

Doing a good job there. So many folk these days would just do a few tack welds along the bottom because "nobody will ever see it".

Nice walk through, thank you.

Manual 1 & Manual 2 modes are high/low impedance, that control the rate of current rise. Use manual 1 mode for thinner repairs with thinner wires where it's important that heat is controlled and manual 2 for larger wires & anything substantial. I've had this welder for over 12 months now, I really can't fault it. Excellent Build quality and packs a real punch. I like the fact that in synergic automatic mode you have the option of letting the machine get you in the 'ball park' very quickly. For any sort of positional work I always default to manual mode so that you've got the ability to dial it in. I've done everything from auto repairs, to mobile structural jobs with this machine! It'll spray 0,8mm wire so can be used for mobile structural fabrication where that mode of transfer is permitted. I'd highly recommend this machine to anyone that's thinking of buying one!

Is the tension housing all made from plastic?

You can buy euro-adapter and use euro torch

I just switched the useless ESAB Handy for an ESAB Prima, and I used the spacer it came with to gap the bridge of the thinner cord. Should I re-do it like you did and double wrap the cord instead?

Hf ignition on mma mode?

Gracias por su tiempo me ayudo bastante

I have been using this machine for two years in really heavy use. The machine has been used in cold, hot, and dusty conditions. Works well ... Kemppi is the best welding machine, that's why I bought it.

can i use argon only for gas?

Would be really good to see how these run ally wire!

hard to find a review in English, thank-you!

I'm slowly getting to grips with shooting these videos, cheers all

I'll have the stinger..send it out and ill use it in my next video :) i like the look of those small ESAB sets.