Відео

Hey Topsky, how about making a way to attach the power supply to the desk top. And tell the executive that accepted this deficiency that it’s NOT ok and they should have more pride in their product than to send it to market like this.

where can I buy this?

And, what’s with the ever so short cord that has to reach the hand control box?! Can’t you spare a few extra inches there. Other than that, just installed and my wife loves it!

Slower indeed. Also, the caption at about 2 minutes in (for the stand) should read 6 x 16 screws, not 6 x 10…

That's dumb. It'll get stuck again.

Slide size?

Is there a more detailed installation video?

My desktop control no longer works, the words "R E S 1" appear on the screen and it doesn't move anymore, do you have a similar problem?

The controller punked out on me while installing 😢😮‍💨😤

Cable for controller is way too small. It does not work with a 30 inch desk. 😮‍💨 Why not include two cable extensions instead of only one?

I have an issue - I didn’t put the desk top yet but decided to test electronics and when press up or down or any preset buttons, it starts moving but then suddenly stops, shows E-2, goes into opposite direction and there is no obstacles! What the heck?! What’s wrong with it? I’ve read in the instruction to disable this gyro function which helped but now no protection for obstacles if I get them in reality like window opened or windowsill accidental catch. Let me know. Thanks! Is it the control box that’s defective or the motors? Or it behaves like that because there is no table top yet on it?

This video was good, if you just ordered the legs without the table top

Um... so... the power adapter, at the end... does it MAGICALLY stay attached to the underside of the desk? You didn't show how to attach it, and I see no instructions on that included with my desk!!! 😡

Fixed my error code issue. Great video thanks 🙏👍

Onde comprar desse

Wow so it just magically attaches to the tabletop?

Worst directions ever. Absolutely no explanation and leaves you hanging at the end on the most important part. Well done. Next time just do it in Chinese so that at least you’re not pretending you’re trying to confuse us.

Why would anyone think a “helpful” video should move so fast????

topsky and ydy nahuy, almost like netflix and chill

thank you for this great demonstration.

These instructions did not help me reset my desk, does anyone have any other suggestions?

For anyone not sure how to bolt the frame to the tabletop: TOPSKY only gives you bolts which cannot go into wood unassisted. I used M6x15mm threaded insert nuts (brand: uxcell) and drilled holes big enough for them. I put the M6x16mm bolts into those inserts and they attached the rail of the frame to my tabletop just fine. The rail of the desk frame adds about ~1-2mm of distance that the M6x16mm bolts need to travel, so the M6x15mm threaded inserts were the right size.

Where is the attachment of the legs to the desk top?

Nice ,thanks

Would be good to use it with a voltage regulator?

Love how the video just skips the table top install😂 we go from frame and feet to just magic

Hey! I’d love to review one of your products if you’d be interested.

Nice aap ka dusra nuskha kaam aya h

Amazing yaar....it worked😊😊😊

The dumbest video I have ever seen Do you work for 5 minutes crafts or whatt!??😐😂😂😂

O.K. But how do you stop this problem from happening again?

Good bless you! I was just about to throw away the suitcase 🤣

In the past, I always had problems assembling the keyboard tray. I would just leave it off the desk. Decades later, just recently assembled a computer desk with a keyboard tray, my old nemesis. The instructions on the desk were so unclear, I went to UA-cam. Your video showed that I had installed the rails wrong and after correcting the problem, I am enjoying my new desk and the keyboard tray!!! Thank you so very much!!

My antivirus block your website, I don't know why?

Really helpful

Imagine skipping an entire step in your installation guide.

I always wondered who would ever need to use the 0.5x playback speed on a youtube video. Now I know.

Worked good👍👍

Not helpful. How do we attach the power supply to the bottom of the desk?

Lift the tip of the black piece away from the metal and then pull apart. Do not press the black piece against the metal.

Just sent you all en email, need help asap!

Enjoying my desk frame so far! Great buy!

Thank you! You hack works

😂 this didn’t fix anything. Great music though.

Mera bhi thik ho gaya

Supurb

I bought the DF04.01. I need to attach the frame to a 6'x30"x1.5" acacia butcher block and I think the best option for me is to use wood screws. I might look for some plastic washers to use so I don't scratch the frame. Do you have any recommendations?

Love everything about this desk except for the keypad design, worst in class. Change it.

Thank you for your tutorial,very helpful

I just put my desk together and was hoping video would help me understand something. That power adapter box at the end....HOW am I supposed to mount it? There is no mounting hardware to hold it against the desk but it will otherwise hang/dangle by that two prong connecter to the control box which can't be good with the weight always pulling on the control box...plus it will be an ugly mass hanging from the center of my desk. WHAT AM I MISSING? This video ends showing the power adapter being plugged in but NO example of what is then done with it.