Відео

Just stumbled on this video . I just purchased a used dynamic boxer like this one but after some play test I got problems with the led panel starting to shut off and on repeatedly. This causes the game to stop taking credits and operating . When I shut it off and turn it back on I’ll get the game to boot and operate just fine a couple min . Then it starts shutting off again. When the panel shuts off the buttons are still lit and the bill acceptor is still lit green . So in short I’m pretty sure I need to replace the power supply as the board works fine when it’s getting power. Long story short I’m new to learning how to fix games . Can you tell me what wires are what on the supply and how to wire up a new supply properly? I would appreciate any help from someone who knows these boxers . Great video and thanks for sharing!

Love this type of video, I'm amazed how quick triotech got XP to boot so quickly

I replaced my motor and im still having problems. I could use some help.

I have a 90's era IceBall machine and I was hoping you might have run across this problem... The ticket dispenser only works on the first game after powering up. Everything works for that first game, but it won't dispense tickets until another power cycle. I have 2 different DL-1275 dispensers that I bought used and they both exhibit the same behavior. I shipped the mainboard to ICE for some repairs (needed a new voltage regulator) but they said the board was dispensing tickets fine for them. Thanks!

Do Dave and busters and more please ❤

Do triotech mad wave motion theater setup please but without the errors❤

Curious to know, what card system are you using? Ive seen this reader on ebay constantly lilke no one wants to use this system.

nice stickers dude!

Hi need operative sistem software plis

I love the attract music on this game

At the end there, you said 'you'll never have to mate them again'. In all my past experience working on this game, it's required the guitars to be mated every time the game gets powered back on, is the firmware you installed a permanent fix for that or do you still need to mate them upon boot-up?

The bracket looks like it is aluminum. Very difficult to weld. You need a TIG welding setup and experience. I think your zip-tie fix will work well until your new parts arrive. Very clever!

second part? thank you i love it

Cool win!

I'm a little bit jealous that you have the ability to bring the assembly to a separate maintenance department in order to cut the shaft. I am the maintenance department. It's all on me. Diag, parts ordering, repairs, etc.

Any arcade that requires buckets of five balls need a good machine for it to be winnable.

This is probably one of the hardest arcade games EVER.

I play monster drop a lot and on 2 of the machines where I play it I won the monster jackpot but the ball ended up getting stuck on the monster hole and I had to get someone to push it through! What do you think could have been the cause as to why it would get stuck and not fall all the way through?

How do you fix "burning mode"

I hope you didn't throw away the button usually just the piece is broken on the micro switch so it's a waste if you did Also I recommend you change the bulb out with an LED one so the heat doesn't cause the plastic to get brittle and break again

😂aaaa

where did you purchase the game trailer?

Good solution (making a game out of it) for an old computer from 2010/2011 :-)

😅aaaa

You can get bigger one and adjust the screen size

Oh man ive seen some gross macgines at some major places. Ive seen a spinderman pusher that was beyond gross.

Candy...Score?...lol

Going back to this. The "your" sensors look bootleg/unofficial. They don't have any official mention like "omc" or "sega gun sense" on them. This explains the cheap build quality on them. I myself am now curious if the sega built sensors work with this game.

Never knew that the XD Theater, Typhoon, etc used DBOX's motion code actuators. Pretty cool!!

Aaaa😂

🎶

Great!... don't error out... one cannot have too many balls on ice ball :)

Those black parts are like... 3d printed.... You can make them yourself :-)

You found the issue. Could be the drive going bad or over time it might have come lose (from the weight hanging). If it does not find any disk it cannot load it's operation system. The game is running a Linux image (probably Ubuntu core or a custom image) and was checking the drive for errors. it's a very small harddrive and probably not as expensive to replace yourself.Btw a SATA extension cord is around 7 dollars you can find it about everywhere where they sell computer parts .

Aaaaaa

E-3

I wonder if that was a polyurethane band on the wheel. Sometimes polyurethane materials just turn into sticky goo.

@4:16 Those RJ plugs are dead cheap and the tool to crimp as well. Wire is available and it's easy too. You can make a new one.

Why are you so funny

Can you put in another monitor?

I guess that because the bearings are at a fixed angle relative to the rotating disk it will never be a perfect movement-match, with always a slight angular slip between them. I wonder if a squirt of a dry lubricant like WD-40 teflon based dry-lube on those bearings from underneath would extend the life of the disk.

It probably is the motor bearings. Made louder by being a stepper motor running at low speed.

@1:15 right hand side is worse.... Probably the rings that they are wearing on their fingers. :-)

They replaced the back lighting of a flat panel TV with their own, put a diffuser in front of it (back plastic)... then a plinko board (that is defusing with white like a normal flat panel TV)... then the rest of the flatpanel tv including the color matrix. and to top if off a layer with some fake fishbowls.... Cool technique! just like a normal flatpanel TV... it also has the back lighting in white etc... i always wondered if they made holes in the matrix for the balls to fall trough... but no... OFC it's much simpler then that 🙂... mind you never have seen these in person, so video's make it seem more real.... you can see it though.

@4:14.. Once an RFID tag of the ticket roll is scanned in the bin below. I has to stop the pusher... Because it needs to scan all RFID tag and dispose the ticket rolls again. If it did not stop the pusher from pushing in more tickets, it could miss any new rolls that might fall in after it's done scanning the RFID tags and after this it also needs to dispose them as well before any new rolls can fall in. So stopping the pusher up top would prevent any new tickets falling in for a moment. It also keeps pushing the ticket rolls out if any are left behind it probably scans for RFID tags again (maybe the rolls are stacked for example, so it needs an extra push). Also you can always scoop for more ticket rolls (if you have credits) even when it's scanning or disposing tickets. This is probably not to slow up the process to much. It would not be much fun to wait for a new scoop once it's counting tickets.... Btw. The extra flash of numbers is the total amount it still has to payout to the card reader. It's fun to see that there is a 8 segment number under the yellow..... why did they not make the yellow line thinner... since the 8 segment is working and is programmed :) over 9000 tickets counted up... wow what a run! 🤣 Though i'm wondering now.... Since you can open the machine.... the RFID tags... Do they share the same ID or a random one?.... maybe the string it get's you (when you scan a roll with your phone) starts with the value of the ticket roll and then a unique number... since it can scan more then 1 of the same value roll....(or maybe you already know).

It looks like one or more of the bearings got stuck at one point in time. It might spin freely now, but better to replace them when you get your new table piece.

very helpful video! keep em coming!

I am so glad we just have two smaller ones lol

Super helpful video man! I hate the way this game is designed haha. Taking it apart is always a chore. Hope that fixed the issue for you!

Your a great arcade technician I watched all your repair videos you really know how to repair these machines