Відео

@@hellhound1389 it's holding up great. The top is well made.

@@TheBoneruner Diluted bleach can be used to clean siding, but it should be rinsed thoroughly.

@@patrickhampton6248 I wish they had a battery to support a great product.

@@CFLDumpsters wow that sounds fantastic! I bet it will look amazing!!!

@@FloridaFamFive you guys did a good job installing.

@CFLDumpsters Thanks! Could of left out the brace as this is a super cutter but they where already there. lt came out good. You will get years of enjoyment from these types of panels!

@@vibewithtrey4046 thanks!

@@1shot-1kill84 That's good to hear! Thanks for sharing!!!

@@jimmahalick639 thanks for letting me know. I like to help. Glad you found this video. A lot of other people have told me they bought a house with the same switch installed. I'm glad I was able to make this video to help so many people! Your comments is what makes it worth it to me!!!

@@tavo5239 that's great to hear! It's fast and easy to use! Thanks for sharing!

@@gator72 The 2 gal is a great choice! I have used the 2 gal for everything even to remove a popcorn ceiling!

@@FloridaFamFive ❤

@@rrk1008 Your Welcome!

@@californiausa7622 Thank you so much!

@@Imscomings Thanks man!

@@thomas8512 yes your right. I do apologize for that. I made a updated video to thos to show how to use it and what it comes with. You can find this on my channel. Hope this helps!

Did you get the Diffuser Accessory Attachment? It helps to make it a little bit quieter. Also Maya the recommendation would be to buy a better hose for it. The one that comes with it isn't that good.

@@FloridaFamFive I see one item called a car nozzle, nothing labeled as a diffuser. the hose is ok not great, but i will use it and if it cracks, will tape it. the car kit hose is $88 where i live, thats NOT worth it for a hose as i already have plenty of car vac tools.

@@Lauren-vd4qe it's a Diffuser for shop vac to reduce blowing dust and makes it sound quieter. Sold at home depot

@@FloridaFamFive i looked on home depot and theres nothing listed as vacuum disffuser. i DO see shop vac mufflers on amazon though

@@thenicepuppy both

@@alexlc1989 your welcome

@@GTA19697 so glad you like it. I have I have 2 of them and use them all the time. I use 1 for a work bench.

@@mtlstreets that's great to hear. This is where I keep mine with some other gear. I take it everywhere. I have had no problems with it at all.

@@herbholmberg4474 wow sounds like a great plan. I would like to see a picture of the finished product. Can't wait to hear how it goes.

I just found a UA-cam video where a guy showed how to remove the drawers. Turns out you remove them the same way you do to remove drawers from old friction slide toolboxes from back in the day. In looking at the lid of the box, I think the easiest way to add a chain stop will be to add thin blocks of steel (keystock from the hdw store) I have not yet measured, but looks like 1/2" keystock strips to underside of lid under the lip of the lid, and matching spot in the bottom of the top till (I will do left side (traditional location on old machinist top boxes) likely just epoxy the strips of steel in place) then drill crosswise through the case and attach each end of the chain with pop rivets (small diameter) after epoxying the strips in I will paint the strips and case as one, the rivet the chain in place afterwards leaving them in their natural zink coat. May first attach all handles and paint as one with the case. (I will figure that out when I get to that point. I am on the fence regarding adding a front fold down cover, may or may not add one of those. May use stainless for a cover and leave bare, or use mild steel and paint the piano hinge and cover along with the rest of the outside as one which would appear more like it came that way when new. I will need very small (thin) piano hinge) the addition of the cover will be dictated by what I can find for the hinge. If I can only find disperportionally sized hinges I won't add a cover because they would stick out Like a sore thumb and destroy the factory made look I will be going after.

If one wished to make these locking boxes that could be easily accomplished by taking a long aircraft drill bit (commonly most of a foot long) and with the lid open and drawers closed drill a hole (1/4") would do through the floor of the top till and through both drawer bottoms and drop a like sized length of steel round stock through leaving 1/2-1" of the rod sticking up from the floor of the top till. Then, mount a small lock hasp to an end of the box for a small lock. I have no such need, but it would be easily accomplished. Mount lock hasp with pop rivets discouraging entry without damaging the box by a screwdriver.

Before I paint the drawers, I will either remove or tape over the aluminum drawer pulls, too.

@herbholmberg4474 tape over them.

@@danielledecaprio3664 once it's set it will run. You can't turn one off you would have to delete it

​@FloridaFamFive thanks, but if I have 2 programs set, one for winter and one for summer, I can't switch one to the other when daylight savings ends? What is the point of having 7 programs if you can't choose which one to run?

@danielledecaprio3664 i see your point. I have not found a way to do that.

@@user-rl9mn6cy9s glad to helped !

@@Jimi-HendrixJr not sure about that. But i can tell you this will make your lawn look amazing. It will help your grass grow look good. Best product that you can put on your lawn from a big box store. Get it and try it. You won't be disappointed!

@@flackramii thanks! I Appreciate that.

@@someguy2707 the saw is a single bevel saw.

@@F22_Raptor that's good to hear thank you so much

@@selw0nk you can't go wrong. I love mine. So many possibilities with desk sizes.. Works great! Let me know how you like you once you get it set up!!

@@CatalinaB-r5q I can see outside.

@@tanajenkinsful I run two LEDs off of it and it seems to work fine.

@@DennisJohnsonDrummer thanks so much. I'm glad you got the chain back on. Glad to help!

@@shaqanglesonyahead4819 im so glad my video helped you out. Hope whatever your cutting went well.

No? Can you give me details?

@@david_J_whittington so glad to hear about this. I'm happy to help! Glad you got it working like you want it to.

@@ariesgirl. Thanks so much. This stuff is amazing. Glad you found the channel. We have lots of video to help with so many things.

@@BenCreechJr sounds like a bad battery. How long have you had it.

@@kevinlewis6616 Your Welcome. Thanks so much! Glad to help.

@@allavinnik6521 Your Welcome! Glad to help!

@@caramelhoney29 Thats a great Ideal. I'll make a video to show this. Thanks for the info

@@tracyjackson7201 thanks so much. Great job today!

Best of both. There are limitations but for a few cuts, it's okay.

Programe 2 should run if you have the day and time set. If you have program 1 set it will run as well. Not sure you can't store a program and it not run.