Відео

Tap con tells me to use a 1/4 inch drillbit for a 1/4 inch screw, that doesn’t seem right because it wouldn’t be secure because it’s the same size as the drill hole. Am I right or wrong?

That was so painful to watch

My slab is 4cm thick. Can i drill straight through and use an anchor?

Helpful. Thanks.

Can you just charge them both and keep one as a replacement

1st timer. Should always blow the dust out of hole. It will stop the screw

What are the parts that you put on first sprinkler called and where did you purchase it?

I would use my drill to drive those tapcons.

Such shoddy workmanship!

Why are you whispering? 🤨

When anchoring into concrete, how big should the hole be relative to the size of the screw?

thank you so much for the videos! i’m going to attempt this over the weekend! curious, did you end up securing it to the cement? if no, have you had any issues with it moving w wind etc?

Drilling into "cement" is pretty simple.Drilling into CONCRETE can be tough though.🤡

Good Job Son! 🤟

Thanks. Saved me a couple of $$$

Great video and easy to follow!

Changed left bulb twice and it still won't work. Right.side works what's.the problem?

Can you provide me with the old battery that you removed? Because I have a gxl V2 and I cannot buy a new battery where I live. Because of how expensive it is, I want your old one and I will maintain it if possible

Good video. However it would help to know what size drill bit , & what size anchors & how deep to drill🤷‍♂️ ijs

You didn’t show the sprinkler head install!

11 minutes to drill 2 holes ? misleading title!!

thank you I used this info today.

Can you do this on stamped concrete driveway?

We are at the point of attaching the trim to the roof panels and there are holes and particular way to install them?

Great 3 videos! Hope we do ok - starting assembly i a couple of days! Thank you!

If I don’t have the Hub and only have the Sensor, can i still connect it with wifi?

Thank you so much!!

Why not set the foot / base where he wants it and drill down through that instead drilling the holes separate and move the base ? especially if the whole project is heavy and hard to move... (Just Extra Steps)

when it rains does the run off create a problem with the sliding door? was thinking of getting one and setting it up the same way. great video

Congrats you have just turned Ro water back into tap water - you completely removed the part that takes away the total dissolved solids So you might as well just get a Brita A complete misunderstanding of what you are doing

Use plastic fischers

This doesn't show squat. Reading the directions?

Can someone tell me exact distance needed between the ground post?

Did you hard strap the base with fasteners to concrete?

😊😊😊

Can these be removed and used again? Same hole?

Can I use the same method for pavers?

Thank you!! Assembly begins tomorrow. Wish me luck!! I watched all 3 videos. Really appreciate the call out on that top screw hole position on the lintel AND the side edges on the very top portion (Q3). I’m sure I will make similar mistakes! Much appreciated!! 😁😁

Hi great video question does the feet have screws that can screw into a wooden deck?

Its best to remove the drill bit from the hole as ur drilling. Helps prevent clog build up.

Bro that’s not the glider I have the glider it’s a peace of shet I can’t even get it to ride

The Rachet starter kit is hard to watch.

Hi, what poles brand are you using?

Thanks

What size changer you need I lost mine

I need to srew into a stone fireplace to hang a mantle . How do I do that? Or who do I call for paid installation?

Riding on gotrax v2 suddenly shut off now no lights on screen and charger doesn't see it. Is there a fuse anywhere?

Trash. Buy a drill kid

Thank you

Excellent video. Why you using your son’s rachet😅