- 111
- 898 960
BCB-Boats Media
Finland
Приєднався 5 гру 2012
Hello and welcome to BCB-Boats Powerboat Channel !
I'am huge powerboat and speedboat enthusiasts from Finland.
My goal is to make interesting and entertaining boat related content.
I will film and create content from the biggest Poker-runs and speedboat events in Scandinavia.
I will also make videos about my own Powerboat projects and introduction videos about the most beautiful
boats here in Northern Europe.
- BCB-Boats Finland
Tino Forsman
I'am huge powerboat and speedboat enthusiasts from Finland.
My goal is to make interesting and entertaining boat related content.
I will film and create content from the biggest Poker-runs and speedboat events in Scandinavia.
I will also make videos about my own Powerboat projects and introduction videos about the most beautiful
boats here in Northern Europe.
- BCB-Boats Finland
Tino Forsman
How to make Fiberglass boat hull in 10 minutes. DIY
Start to finnish project. We made small row boat / dinghy from fiberglass. How to make a boat by using mold? We used polyester resin, csm chopped strand mat, bi-axial cloth, gelcoat and we made topcoat from gelcoat with parafine.
Переглядів: 48 532
Відео
The most beautiful FOUNTAIN Powerboats at Pokerrun 2024
Переглядів 1,5 тис.Місяць тому
Saaristo Pokerrun 2024 Nauvo, Finland.
Powerboats Making a Spectacle for Audience at Poker-Run Event.
Переглядів 6 тис.Рік тому
Powerboats Making a Spectacle for Audience at Poker-Run Event.
Powerboats Racing in the Finnish archipelago!
Переглядів 1,8 тис.Рік тому
Powerboats Racing in the Finnish archipelago!
Outerlimits Powerboat throwing HUGE Roostertail!
Переглядів 1,2 тис.Рік тому
Outerlimits Powerboat throwing HUGE Roostertail!
The Best Outboard Motor in the World ! Evinrude 250hp e-tec G1.
Переглядів 29 тис.Рік тому
The Best Outboard Motor in the World ! Evinrude 250hp e-tec G1.
Loud Powerboats in Poker Run. #Fountain
Переглядів 804Рік тому
Loud Powerboats in Poker Run. #Fountain
Cigarette 42x Powerboat with Twin Big-Block Mercury Racing Charged V8 Engines.
Переглядів 5 тис.Рік тому
Cigarette 42x Powerboat with Twin Big-Block Mercury Racing Charged V8 Engines.
Ocean Express 33 with Twin Evinrude 300hp e-tec G1 engines. Outboard Conversion
Переглядів 1,1 тис.Рік тому
Ocean Express 33 with Twin Evinrude 300hp e-tec G1 engines. Outboard Conversion
Skater 388 with Twin Mercury Racing 1350hp Bi-Turbo V8 Engines
Переглядів 3,3 тис.Рік тому
Skater 388 with Twin Mercury Racing 1350hp Bi-Turbo V8 Engines
Nor-Tech 3900 Powerboat Leaving Harbor for Speed Challenge.
Переглядів 714Рік тому
Nor-Tech 3900 Powerboat Leaving Harbor for Speed Challenge.
Apache 41 Powerboat. 2x 1200hp Supercharged V8 Engines.
Переглядів 18 тис.Рік тому
Apache 41 Powerboat. 2x 1200hp Supercharged V8 Engines.
Insane Fast Powerboats! The Powerboat Movie 2022 Sweden/Finland
Переглядів 3,9 тис.Рік тому
Insane Fast Powerboats! The Powerboat Movie 2022 Sweden/Finland
Inboard to Outboard Conversion. DIY Bracket
Переглядів 35 тис.Рік тому
Inboard to Outboard Conversion. DIY Bracket
The Fastest Boats in Europe! Hanko Poker Run 2022
Переглядів 10 тис.2 роки тому
The Fastest Boats in Europe! Hanko Poker Run 2022
Go Fast Rib Catamaran. Twin Mercury Racing 400R Outboard Motors. Powerboat Spotting 2#
Переглядів 1,9 тис.2 роки тому
Go Fast Rib Catamaran. Twin Mercury Racing 400R Outboard Motors. Powerboat Spotting 2#
Ekenäs Powerboat Club FUN RUN 2022.
Переглядів 2,9 тис.2 роки тому
Ekenäs Powerboat Club FUN RUN 2022.
Quad Mercury 600HP V12 Verado. The World's Biggest OB Engines. Powerboat Spotting 1#
Переглядів 3,8 тис.2 роки тому
Quad Mercury 600HP V12 Verado. The World's Biggest OB Engines. Powerboat Spotting 1#
SAARISTO POKER RUN 2022. Unique FOUNTAIN 38 !
Переглядів 12 тис.2 роки тому
SAARISTO POKER RUN 2022. Unique FOUNTAIN 38 !
How To Calculate Boats CENTER OF GRAVITY. Inboard to Outboard Conversion
Переглядів 10 тис.2 роки тому
How To Calculate Boats CENTER OF GRAVITY. Inboard to Outboard Conversion
Inboard to Outboard Conversion. How to make BRACKET that WORKS?
Переглядів 37 тис.2 роки тому
Inboard to Outboard Conversion. How to make BRACKET that WORKS?
SPEEDBOATS LEAVING HARBOR INLET FOR POKER-RUN
Переглядів 1,8 тис.2 роки тому
SPEEDBOATS LEAVING HARBOR INLET FOR POKER-RUN
The Most Unique Powerboats in Europe. Insane Loud V8 Sounds
Переглядів 8 тис.2 роки тому
The Most Unique Powerboats in Europe. Insane Loud V8 Sounds
Skippi 650 Race, Sailboat. First Test!
Переглядів 5 тис.3 роки тому
Skippi 650 Race, Sailboat. First Test!
How to fix Rotten Transom & Stringers on a Boat. Tips!
Переглядів 19 тис.3 роки тому
How to fix Rotten Transom & Stringers on a Boat. Tips!
Hanko poker Run 2021. Fast Catamarans!
Переглядів 4,3 тис.3 роки тому
Hanko poker Run 2021. Fast Catamarans!
Boats Outboard Conversion. DIY Bracket / Pod for Outboard engine.
Переглядів 50 тис.3 роки тому
Boats Outboard Conversion. DIY Bracket / Pod for Outboard engine.
That engine at the end was awesome. Great idea.
🤣👍
Fibre glassing is a bit like plastering, once you've mixed it you're fully committed, not sure I could handle the pressure! great job, great vid👍
You are 100% right. Thank you!
Cool Job and you put a casting deak on the front?? I think they would sell well with the hatchs in the front for storage all so the latrex 335 i was looking at but no deck or hatch in the front
How much did each material cost
About 700€
"Buy or rent a mold" ??? I've looked for mold rental businesses in my mountain city. I find only mold removal businesses.
Anyone watching can instantly tell, inspecting the mould, carefully cleaning it, allowing it to dry, finding and taping the imperfections, waxing it …..took way more then ten minutes and that was just the prep! Then you have to fibreglass it, carefully resin or epoxy it and wait at least a few hours for it to set up! I have done fibre glass setup work and impossible to do it in “ ten minutes”!! What a load of malarkey!!
xD
2 x 1200 hv
very nicely explained. Very technical which I appreciated.
Engine size at the end😂😂
;)
Cigarette 42X "No Xcuses"🤩
Awful music, and an equally awful power package
Why’d you play music over top of that awesome video?
Better without?
Where do you buy or rent pre-made boat mold?
Used market
Damn i want one
Tax dollars hard at work 😂😂😂
I would have gone for triple 500hp motors.
:D
I am sorry but your pronunciation is hard to understand in English. Did you say ( you must also check that you don’t make too light bracket because the water rises up from the boat bottom also there .. ? ). If that’s not exactly what you said. Please correct me if I’m wrong. ======= > it is said near 4:04 minutes of video.
I think you say too wide bracket. damn, your diction is awful. lol
I know its bad. Sorry about that.
@@BCB-Boats-Media no problem. In the end I understood your tips quite well. There was only one thing that isn’t quite clear for me. You explained about the rule of the thumb for every one feet set back on the transom, the engine must be lifted one inch high. But I didn’t get it whether it’s one inch high in relation to the keel ( as we usually set the engine’s anti cavitation plate ) or it’s in relation to the bottom of the bracket. Please. Can you clarify it to me ? I am about to set my engine height and I am kind of lost here.
Oxe
I don't see oar locks or a transom for a motor. How much does the material cost.
Yamaha on paras kaikista moottoreiata
nice
I know nothing about boats. Is a v8 good for a boat😭
The best 👌😎
Evinrude E-tec. 😬 mahtookohan rantautua suomen kamaralle näitä brp rotax koneita?
Epäilen 😬
Mercury vaikka itelläni onkin honda😂
Honda
Looks like you bought a figerglass boat added a few more layers and mods. I didn' t see a boat being built SMH.
What? 🤣 I dont understand how its even possible to misunderstand the video like that. Did you even watch the video??
@@BCB-Boats-Media😂 I realised I didnt finish the video. Not sure how I missed the separation at the end.....anyways sorry for being an ass. The boat looks great👍
Thanks, I really enjoyed watching
Nice work. Can't wait to see it with the engine for the test run.
so this thing actually took you several hours it's just standard glass layup -- So what ?
👎
The video is 10 minutes silly
i think the ideai is to show people who have never done it or doing it first time
350 v8 on that thing? 🤣 why not use 2?
👌🤣
That`s just the "kicker" LOL
Kyllä katamaraaneissa vaan on sitä jotain, mutta 2:04 nurkilla olevan veneen eleetön kulku on hienon näköistä myös.
Hienoin oli se 1 min 30 sek kohdan fountain mikälie ja parhaiten taisi uida kuin juna raiteillaan tuo vene #43 2 min kohdalla. Ottaisin kyllä jälkimmäisen jos pitäisi mennä kovassa merenkäynnissä.
When this thing came out, there was nothing that could respond to it. The 250s and 300s offered an almost perfect symbiosis of 2 stroke and 4 stroke benefits with almost none of the drawbacks of either. What a letdown and mistake the g2 was
Wow
That looks just like peggies apache but his had blue letters for apache
Do you have a list of tool to do this job think long about to try this on a free boat I got ?
Sorry, but I dont have a list.
Very useful video! I am looking to convert my 1995 Bayliner Ciera 2655. It has a V8 260hp inboard engine, and I fear it will start falling apart and cause a lot of costs. However, I will not put anything bigger than a 30hp outboard on the bracket. Do you think it´s possible to mount a bracket under the swim platform and bolt it to the platform? I could initially leave the old drive shaft there and deal with that in the winter.
3 for sound
💪
One dollar Bob
I feel bad for whoever has to work on those.
🔥🔥🔥
Kyllä eemelin vehkeille on ihmettelijöitä
how did you blue the two edges of fiberclass between the mold and the one in the boat ? I am kinda worried about this bond, even after laminating figerglass from the bottom of the boat and inside the boat. I'm having to do the same on my boat, but I am extending only 6 inches long. would you give me some hints ? I will be using polyester resin , plywood for the transom and fabric for the hull.
I saw someone grinding the edges in 90 degrees angle and laminating it on and under.
Taitaa olla Saimaan nopein vene. Sadan solmun raja meni rikki toukokuussa. Kesällä 2023 kopassa luki vielä 250R, joten silläkin lienee osuutta asiaan 😉 Imatran vauhtivene-expertti Eemeli Nenonen on muokannut Twisteristä todella upean ”daycruiser-katin”, joka toimii hyvin retkiveneenäkin. Ehtii sadetta pakoon tarvittaessa varsin ripeästi 😉
😎👍👍
Someone needs to buy them out and bring back the Gen1. They were awesome outboards.
Yes indeed!
2 x 1200hp
What about Gen 2 300hp those any good
With good maintanance they are also reliable but I think they have still.more problems than G1. Powerwise both are awesome choices 👌
@@BCB-Boats-Media ok so gen 1 the way to go then? I’ve been looking at some used ones and price isn’t bad seen a dual 300gen for 19k with 91 hours is that good??
Mörkö! 🤌🏻
💪
Tell me the true Cubic inches and if they are Supercharged but just by the sound they are Big Blocks with Race cams so between 800 and 1000 Horsepower each. 1600 to 2000 total.
572 cid supercharged engine x 2
165