Відео

Thanks for watching 💪

I don’t, I couldn’t find one online either

Thanks for watching! I don’t remember the part number but I’m pretty sure I show it somewhere in the videos

I use a mix of gravity, rope and galvanized strapping. I would suggest sealing your barrels at a colder temperature so that they prevent from collapsing. Foam can leak out and I find is not necessary

@@tom_sassen That’s an odd reply, since the foam turns into a solid waterproof material after just a few minutes. Once it’s dry and solid, it can’t leak anywhere and the plastic barrel is just a protective layer at that point. We must be thinking of two different materials.

I’ll have to check it out

Awesome! Have a good one

@@tom_sassen Thank you Tom, I'm Savin from Indonesia. I'm planning glamping On a boat. I find your design very interesting if I put a tent on it.

That’s too bad

Haha that’s true!

Depends on the size of the boat. Probably like 20-30km|h

Cheers thank you

Thanks!

No engine oil? It’s a 2stroke, I mix it with my gas

Hi , how can be without oil ?, is an crangshaft turning the pistons . 2 pcs ,I understand that using use oil to lubricate on burning but rotation of the pistons is done by an crangshaft this must have oil. The oil for the gear is clear ,oil 2T on fuel is ok ,,how is possible without motor oil,, . Can someone push me on that video to clarify the situation ?Thanks

I believe off Amazon!

No problemo

Nice!

Do you have a manual by chance for this motor ? ​@@tom_sassen

I just got the same engine and I haven’t gone through it yet. I plan to this week but the person that sold it to me said they were having trouble getting it started but when they did, it would run OK but then bog out they said that they were having to spray gas into the carb throat so they assume That it’s a carb float hopefully in the next week or so I’ll get it taken apart great video btw

It could be your fuel pump to more them likely if you put in a new carburetor kit..

Nice!

Thank you

Nice!

Gotta get tracks lol

Thank you

It depends, I don’t think it would float too well since they can only displace 450 ibs of water

@@tom_sassen what if I also packed said concrete with lots and lots of sealed empty water bottles?

Yep! It pumps properly that way

Nope! I got some cheap ones from Canadian tire and they seem to have held up two years later, even the ones submerged underwater are still good, must be stainless or aluminum

@@tom_sassen Thanks a lot!

I’ve never thought of that but that’s a very good point! That’s something that should be considered for sure, it would be cool to put a 3d model in a water simulator to see the difference with and without for drag.

I could! I would probably need to Fiberglas them though too

Lol agreed

We don't need to see your face, just show us the work you did

What else can be used besides barrels that are already pressurized

It wasn’t built correctly and I found it didn’t look right. If it was better built I would have kept it

that's a good idea if you have access to a plastic welder!

I’m making a new video on how to do it!

What?😂

That would’ve helped! I think the frame should have been all metal. And the wheels should’ve been stronger

Yeah my grandpa has something like that. It’s tracks are two very large H beams. Works like a charm. The blue wheels are more for light duty vehicles like small jet skis and small tow boats

great job man!! love it! the ol duct tape ratchet strap trick haha the best!

@@brandocommando36 Haha it works thanks!

tks for showing your mistakes , not many do. better luck next time, boats have a keel, we can use a roller there too, so the weight is on keel, the the chines(sides) dont get all the weight, causing friction and leaning,wood works ok, but overtime it deteriorates, honestly the beams were a bit weak for you project, the wheels were inferior to the weight, yet it might have work great for a while if more were screwed on :) anyways, some we win and some we loose, atleast we learn from our mistakes (school money) hehe..

Yeah it takes a while to drive them by hand. I'm planning on rebuilding my little work barge this year and putting a crane on it as well for boat lifts and docks too. I won't be putting any forks on it due to budget constraints but it is a busy business! Are you Canada or US?

I thought about it! I don’t think so though, without serious modifications I don’t know if it’s possible.

@@tom_sassen is there just not enough clearance? The 10in dirt tires are super cheap, so if I do buy a metro I'll just give it a try and if it doesn't fit, I'm only out $45

I had to remove the back inside fender on my metro but I'm gonna put it back on with some washers so it can fit @@mgpBLARG

9.9

idk

nice