- 61
- 121 070
Da Si
Slovenia
Приєднався 24 чер 2008
UA-cam is full of videos to teach CAD basics. But very rarely you can find videos that explain how to set up templates, define your own standard parts, etc.
As a technical support engineer, I have recorded several videos to support NX and Solid Edge users over the years. I will try to regularly post videos, that explain not only basic modeling techniques, but also various NX and Solid Edge settings.
As a technical support engineer, I have recorded several videos to support NX and Solid Edge users over the years. I will try to regularly post videos, that explain not only basic modeling techniques, but also various NX and Solid Edge settings.
Solid Edge modeling - control and limit variables with sensors and variable rules
This movie will explain how to control variable values or measurements with sensors. It will also explain how to limit values using the variable rule editor.
00:00 Intro
00:33 Variable Sensor
02:17 Minimum Distance Sensor
03:37 Variable Rule Editor
00:00 Intro
00:33 Variable Sensor
02:17 Minimum Distance Sensor
03:37 Variable Rule Editor
Переглядів: 121
Відео
Solid Edge modeling - Adjustable Part
Переглядів 6228 днів тому
This movie will explain how to create an adjustable part like a spring. The purpose of creating this kind of part is to adjust its geometry according to its position in the assembly. 00:00 Intro 00:04 Create an adjustable part 02:28 Create an assembly 03:28 Add the adjustable part 04:16 Make a change to the assembly
Siemens NX - Assembly Sequence
Переглядів 4467 місяців тому
Siemens NX has many functions and options, that users are not familiar with. In the series 'Siemens NX - Lesser known features and options' I will try to explain some of them. Sometimes it is better to create an animation of how to assemble an assembly instead of just creating an exploded view. To do this in NX, you can use the Sequence environment. 00:07 Create a new Assembly Sequence 00:44 Re...
Solid Edge Assembly - simple motion analysis
Переглядів 2018 місяців тому
This movie will explain how to do a simple motion analysis, check for collisions and use different motors to animate mechanisms. 00:00 Intro 00:08 Drag Component command - simple motion 01:26 Placing the mechanism in a higher assembly 02:20 Rigid vs Adjustable assembly 02:43 Adjustable assembly issue 03:18 Place the assembly as an adjustable assembly 04:38 Completing the assembly 06:52 Motion a...
Solid Edge Design Manager - create a new drawing from an existing one
Переглядів 1159 місяців тому
This movie will explain how to use an existing drawing to create a new drawing for a mirrored part. The same technique can be used for drawings of similar parts. 00:00 Intro 00:07 Create a mirrored part 00:33 Create drawing of a mirrored part
Siemens NX - Chain selection within the Curve Rule
Переглядів 3239 місяців тому
Siemens NX has many functions and options, that users are not familiar with. In the series 'Siemens NX - Lesser known features and options' I will try to explain some of them. Sometimes it is not easy to select all the edges needed for an extrude command or any other command, that needs edges or curves for input. Selecting only from the Curve Rule menu is not enough. In such cases, the exact so...
NX accelerators - ALT, CTRL, SHIFT and similar in the drawing
Переглядів 15510 місяців тому
Siemens NX has many functions and options, that users are not familiar with. In the series 'Siemens NX - Lesser known features and options' I will try to explain some of them. NX accelerators can greatly improve the use of software. In this movie, I will show some of these in a drafting environment. 00:00 Intro 00:07 SHIFT ALT 2nd curve - Select all edges between the two selected 00:47 ALT - Di...
NX accelerators - ALT, CTRL, SHIFT and similar in the assembly
Переглядів 12110 місяців тому
Siemens NX has many functions and options, that users are not familiar with. In the series 'Siemens NX - Lesser known features and options' I will try to explain some of them. NX accelerators can greatly improve the use of software. In this movie, I will show some of these in an assembly environment. 00:00 Intro 00:23 CTRL Left Mouse Button - Copy the component 01:10 CTRL ALT Left Mouse Button ...
NX accelerators - ALT, CTRL, SHIFT and similar in the modeling
Переглядів 26610 місяців тому
Siemens NX has many functions and options, that users are not familiar with. In the series 'Siemens NX - Lesser known features and options' I will try to explain some of them. NX accelerators can greatly improve the use of software. In this movie, I will show some of these in a modeling environment. 00:00 Intro 00:07 ALT ENTER - Full Screen Mode 00:17 ALT - display toolbars in Full Screen mode ...
NX accelerators - ALT, CTRL, SHIFT and similar in the sketch
Переглядів 19110 місяців тому
Siemens NX has many functions and options, that users are not familiar with. In the series 'Siemens NX - Lesser known features and options' I will try to explain some of them. NX accelerators can greatly improve the use of software. In this movie, I will show some of these in a sketch environment. 00:00 Intro 00:21 ALT - ignore relationships 00:52 Middle Mouse Button - remember relationships 01...
NX - Deselect edges from Edge Blend with different selection intent rule
Переглядів 83611 місяців тому
Siemens NX has many functions and options, that users are not familiar with. In the series 'Siemens NX - Lesser known features and options' I will try to explain some of them. When edges are deselected from an Edge Blend, NX will always use the selection intent rule, that was used when the Edge Blend was created. This movie shows, how to deselect just few edges from the Edge Blend feature. 00:0...
Siemens NX - Control over Design Requirements (Add a Check)
Переглядів 19811 місяців тому
Siemens NX has many functions and options, that users are not familiar with. In the series 'Siemens NX - Lesser known features and options' I will try to explain some of them. The first are Add a Check and Requirements Validation. With these options, the user can have complete control over the critical dimensions of their parts and/or assemblies. 00:00 Intro 00:07 Add a Check 00:55 See the resu...
Solid Edge for Beginners - How to create a simple assembly?
Переглядів 17911 місяців тому
There are many movies on how to create different types of models. But it's rare to find a movie with all the basic modeling steps. The new movie will show, how to create a simple assembly and how to easily move the components. 00:00 Intro 00:17 Position components with assembly relationships 09:37 Use the Pattern command 11:19 Move the component 13:54 Define the range of motion
Solid Edge for Beginners - How to create a simple sheet metal model?
Переглядів 10711 місяців тому
There are many movies on how to create different types of models. But it's rare to find a movie with all the basic modeling steps. The new movie will show, how to create a simple sheet metal model and its flattened state. 00:00 Intro 00:21 Using the Tab command 02:57 Constructing Flanges 04:53 Creating Deformation features 06:03 Adding Holes 07:48 Rounding sharp corners 08:18 Feature mirroring ...
Solid Edge analysis - How to change a mass property?
Переглядів 126Рік тому
Sometimes we add parts with imprecise geometry or no geometry at all. In both cases, an accurate mass property is required. This movie shows, how to change the model mass and how to change the mass information in the parts list. 00:00 Intro 00:05 Change the mass of the model 00:39 Create a non-geometric part with a mass property 01:35 Create a non-geometric part with no mass property 02:16 Chan...
Solid Edge for Beginners - How to create a drawing?
Переглядів 74Рік тому
Solid Edge for Beginners - How to create a drawing?
Solid Edge for Beginners - How to easily edit a model?
Переглядів 171Рік тому
Solid Edge for Beginners - How to easily edit a model?
Solid Edge for Beginners - How to create a simple model?
Переглядів 73Рік тому
Solid Edge for Beginners - How to create a simple model?
Solid Edge - Feature count with Dimension command
Переглядів 85Рік тому
Solid Edge - Feature count with Dimension command
NX Modeling Tips (File structure): Suppressed and Buried features and Solid Voids
Переглядів 299Рік тому
NX Modeling Tips (File structure): Suppressed and Buried features and Solid Voids
NX Modeling Tips (File structure): Fix all errors
Переглядів 208Рік тому
NX Modeling Tips (File structure): Fix all errors
NX Modeling Tips (Assembly): More predictable and stable assemblies using the Product Interface
Переглядів 94Рік тому
NX Modeling Tips (Assembly): More predictable and stable assemblies using the Product Interface
NX Modeling Tips (Assembly): Top-down use of inter-part links
Переглядів 215Рік тому
NX Modeling Tips (Assembly): Top-down use of inter-part links
NX Modeling Tips (Modeling): Model structure, when to create Edge Blends
Переглядів 116Рік тому
NX Modeling Tips (Modeling): Model structure, when to create Edge Blends
NX Modeling Tips (Modeling): Carefully position sketch on face
Переглядів 85Рік тому
NX Modeling Tips (Modeling): Carefully position sketch on face
NX Modeling Tips (Sketch): Pattern Curve (complex sketch) vs Pattern Feature (simple sketch)
Переглядів 179Рік тому
NX Modeling Tips (Sketch): Pattern Curve (complex sketch) vs Pattern Feature (simple sketch)
NX Modeling Tips (Sketch): Fillet vs Edge Blend
Переглядів 118Рік тому
NX Modeling Tips (Sketch): Fillet vs Edge Blend
Solid Edge - Adding parts to the standard part library
Переглядів 624Рік тому
Solid Edge - Adding parts to the standard part library
NX drawing - How to separate a drawing from the model file
Переглядів 532Рік тому
NX drawing - How to separate a drawing from the model file